幾種貓路由設置方法.doc

幾種貓路由設置方法合勤 P642首先P642是TELNET模式，所以首先在運行里輸入TELNET 確定后開啟TELNET！然后點擊“連接”“遠程系統”在主機名里添入192.168.1.1這是P642默認IP！然后連接出現Password：在后面輸入默認的密碼1234回車后進入下面的設置界面 Copyright (c) 1994 - 2000 ZyXEL Communications Corp. Prestige 642R Main Menu Getting Started Advanced Management 1. General Setup 21. Filter Set Configuration 3. Ethernet Setup 22. SNMP Configuration 4. Internet Access Setup 23. System Password 24. System Maintenance Advanced Applications 11. Remote Node Setup 12. Static Routing Setup 15. SUA Server Setup 99. Exit 這些都是各功能界面按前面的數字和回車來進入各界面！ 下面進入1. General Setup 界面，只要輸入“1”回車即可，以此類推！我只登出需要更改的界面！ - Menu 1 - General Setup System Name= p642 （隨便起名） Location= Contact Persons Name= Route IP= Yes （要開啟路由這里必須改成YES） Route IPX= No Bridge= No （這里必須NO） Press ENTER to Confirm or ESC to Cancel: - 設置好后回車存儲，然后按ESC回主界面！ 再進如3. Ethernet Setup 繼續進2.TCP/IP and DHCP Setup - Menu 3.2 - TCP/IP and DHCP Ethernet Setup DHCP Setup DHCP= Server Client IP Pool Starting Address= 192.168.1.33 Size of Client IP Pool= 32 Primary DNS Server= 202.97.224.68 Secondary DNS Server= 202.97.230.4 Remote DHCP Server= N/A TCP/IP Setup: IP Address= 192.168.1.1 IP Subnet Mask= 255.255.255.0 RIP Direction= Both Version= RIP-1 202.97.224.68和202.97.230.4為當?shù)仉娦诺?個DNS，各地不同。只有一個也可 其他的按照我的設置改即可 回車存儲 下面回到主菜單進入4. Internet Access Setup - Menu 4 - Internet Access Setup ISPs Name= ChangeMe （這個名字也隨便了） Encapsulation= ENET ENCAP 必須和電信提供參數一致 Multiplexing= LLC-based 必須和電信提供參數一致 VPI #= 0 （VPI VCI值問當?shù)仉娦牛?VCI #= 35 Service Name= N/A My Login= N/A My Password= N/A Single User Account= Yes 為開啟項，默認為 IP Address Assignment= Static IP Address= 218.10.165.196 （這是電信給你的IP） ENET ENCAP Gateway= 218.10.165.193（這是電信給你的網關 IP，網關每戶不同） Press ENTER to Confirm or ESC to Cancel: - 回主菜單進11. Remote Node Setup再繼續進1， - Menu 11.1 - Remote Node Profile Rem Node Name= ChangeMe 不是一行 Route= IP Active= Yes 不是一行 Bridge= No Encapsulation= ENET ENCAP 不 Edit PPP Options= N/A Multiplexing= LLC-based 不 Rem IP Addr= 218.10.165.193 Incoming: 不 Edit IP/IPX/Bridge= No Rem Login= N/A Rem Password= N/A Outgoing: Session Options: My Login= N/A Edit Filter Sets= No My Password= N/A Authen= N/A Press ENTER to Confirm or ESC to Cancel: - 注意上面應該為兩列，為防止混淆我用文字夾在中間了，后面的沒夾文字自己注意218.10.165.193為網關 每戶都不同！ 進12. Static Routing Setup然后續進1，在進1， Menu 12.1.1 - Edit IP Static Route Route #: 1 Route Name= test Active= Yes Destination IP Address= 0.0.0.0 IP Subnet Mask= 0.0.0.0 Gateway IP Address= 218.10.165.193 Metric= 2 Private= No Press ENTER to Confirm or ESC to Cancel: 以上修改后就可開啟路由了！ 另外23. System Password是修改進入密碼的！ 24. System Maintenance 然后繼續進4再繼續進21就自動重起路由器，這在掉線后恢復連接有用！這跟拔掉路由器電源再插上類似，像重起電腦！ 另外24. System Maintenance里面有一項是恢復出廠默認的，具體的忘了，自己試吧！ 記住每頁設置完一定要回車存儲！ 下面是關于PPPoE模式路由的開啟！用telnet登陸，在運行里輸入telnet 192.168.1.1。密碼初始為1234，進入： Copyright (c) 1994 - 2000 ZyXEL Communications Corp. Prestige 642R-11 Main Menu Getting Started Advanced Management 1. General Setup 21. Filter Set Configuration 3. Ethernet Setup 22. SNMP Configuration 4. Internet Access Setup 23. System Password 24. System Maintenance 25. IP Routing Policy Setup Advanced Applications 11. Remote Node Setup 12. Static Routing Setup 15. SUA Server Setup 99. Exit 設置Router 工作模式: 進入菜單1 Menu 1 - General Setup System Name= hfkj Location=huafeng Contact Persons Name=sjz Route IP= Yes Route IPX= No Bridge= No 注意必須打開Route IP 進入菜單3.2 Menu 3.2 - TCP/IP and DHCP Ethernet Setup DHCP Setup DHCP= Server Client IP Pool Starting Address= 192.168.1.33 Size of Client IP Pool= 32 Primary DNS Server= 0.0.0.0 Secondary DNS Server= 0.0.0.0 Remote DHCP Server= N/A TCP/IP Setup: IP Address= 192.168.1.1 IP Subnet Mask= 255.255.255.0 RIP Direction= Both Version= RIP-1 Multicast= None IP Policies= Edit IP Alias= No 進入菜單4 Menu 4 - Internet Access Setup ISPs Name= ChangeMe Encapsulation= PPPoE Multiplexing= LLC-based VPI #= 0 VCI #= 35 Service Name= My Login= 82303#1 My Password=* Single User Account= Yes IP Address Assignment= Dynamic IP Address=N/A ENET ENCAP Gateway= N/A 進入菜單11.1 Menu 11.1 - Remote Node Profile Rem Node Name= ChangeMe Route= IP Active= Yes Bridge= No Encapsulation=PPPoE Edit PPP Options=No Multiplexing= LLC-based Rem IP Addr=0.0.0.0 Incoming: Edit IP/IPX/Bridge= No Rem Login= Rem Password=* Outgoin