機器人專業詞匯中英文對照.

1、ACAS Applicator Cleaner Air Supply 霧化器清洗器供氣pACS Applicator Cleaner Solvent Pilot 霧化器清洗器溶劑控制閥ACS Applicator Cleaner Solvent 霧化器清洗器溶劑ACVA Applicator Cleaner Vacuum Air 霧化器清洗器真空空氣ACDA Applicator Cleaner Drying Air 霧化器清洗器干燥空氣BEAR Bearing Air 軸承空氣BAO Bearing Air OK 軸承空氣正常BRAKE Brake Air Turbine 渦輪剎車空氣pBW

2、 Bell Wash Pilot 旋杯清洗控制閥BWS Bell Wash Supply 旋杯清洗供應AIR Color Change Air Supply 換色空氣供應SOL Color Change Solvent Supply 換色溶劑供應CP# Color Pilot (#) = Color 顏色控制閥（#）= 顏色DUMP Dump 排放DAT Drive Air Turbine 渦輪驅動空氣E-STAT Electrostatics 靜電pIW Injector Wash Pilot 注射器清洗控制閥IWS Injector Wash Supply 注射器清洗供應PAINT Pai

3、nt 油漆PAP Purge Air Pilot 沖洗空氣控制閥pCC Pilot Color Change 換色控制閥PCE Process Control Enclosure 工藝控制柜pDUMP Pilot Dump 排放控制閥PDP Power Distribution Panel 配電柜PIE Process Interface Enclosure 工藝接口柜PREG Pilot Regulator 調節器控制閥PR# Paint Return (#) = Color 油漆回路（#）= 顏色PS# Paint Supply (#) = Color 油漆進路（#）= 顏色pPS Pur

4、ge Solvent Pilot 沖洗溶劑控制閥pTRIG Pilot Trigger 觸發器控制閥PTS Pilot Trigger Supply 觸發器供應控制閥RP Robot Purge 機器人凈化SA1 Shaping Air (Bell Applicator) 成形空氣（旋杯霧化器）SA2 Shaping Air (Bell Applicator) 成形空氣（旋杯霧化器）SAP Shaping Air Pilot 成形空氣控制閥SAS Shaping Air Supply 成形空氣供氣SCC System Control Console 系統控制柜TDP Turbine Drive

5、 Pilot (Bell Applicator) 渦輪驅動控制閥（旋杯霧化器）TURB Turbine Drive Supply 渦輪驅動供氣Purge System Maintenance凈化系統維護- Purge System Diagnostics凈化系統診斷- Purge System Testing andCalibration凈化系統測試和校準- Purge Cycle Troubleshooting凈化循環排錯 Color Changer Assembly換色器組件- Color Changer Valve Maintenance換色閥門維護 SolvAir Module Set

6、up and Maintenance溶劑空氣模塊設置和維護 3 Valve IK Gear Pump3閥門1K齒輪泵- Pump Block Pressure Sensor泵的壓力傳感器 Process Control Maintenance工藝控制維護- Fluid Presets Maintenance流體預設值維護- E-stat Presets Maintenance靜電預設值維護- Preset Override Maintenance強制預設值維護- Color Change Maintenance換色維護 Pepperl & Fuchs ISB SettingsPepperl &

7、 Fuchs ISB設置 Robot Software Maintenance機器人軟件維護- I/O Re-configurationI/O 重新配置- Robot File Copy機器人文件復制- Robot System Variables EditingTransducer Operations比例閥的操作- Shaping Air Control成形空氣的控制- D/Q Shaping Air Control ModuleD/Q 成形空氣控制模塊- Turbine Speed Control渦輪速度控制- Keyence Digital Fiber SensorKeyence 數字

8、光線傳感器 Fluid Calibration - Beaker Method流體校準 量杯的方法 System Configuration Maintenance系統配置維護- System Colors Maintenance系統顏色維護- Styles Maintenance車型維護- Option Maintenance選項維護- PW3 SetupPW3 設置機器人系統變量編輯- Software Archive軟件存檔- Backup a Robot Image備份一個機器人鏡像- Restore a Robot Image恢復一個機器人鏡像 Paintworks III Soft

9、ware MaintenancePaintworks III軟件維護- Creating a Norton Ghost 2003Boot Disk Set創建一個Norton Ghost2003 啟動盤- Backing Up Your PAINTworks IIIGUI備份你的PAINTworksIII GUI。- Copying Your Ghost Image Filesto CDs把你的Ghost 鏡像文件復制到CDs。- Restoring Your PAINTworks IIIGUI恢復你的PANITworks III GUI。pAIR PAP Pilot input for Pu

10、rge Air凈化空氣的驅動輸入pSOLV PSP Pilot input for Purge Solvent凈化溶劑的驅動輸入AIR CCAS Purge Air supply input凈化氣源輸入SOL CCSS Purge Solvent supply input凈化溶劑供應輸入pCC PCC Pilot for Color Changer operation. When this input is enabled, thepurge air and solvent mixture will be directed to the color changermanifold as aer

11、ated solvent.換色器操作的驅動。這個輸入被激活時，凈化空氣和溶劑混合物會直接通向換色器多只管，像充氣的溶劑一樣。2T Output 2T Secondary output (used for Applicator Wash). Solvent or air or theaerated mixture is always available at this port. If it is not requiredin the system, the port must be plugged.二次輸出（用于霧化器清洗 ）。在這個端口一直有溶劑、空氣或者混物。如果系統沒有要求，這個端口必須

12、被塞緊。1K Process Assembly with a Regulator 含調整器的1K 工藝組件EO-4696-511-000 Rev. A Sheet 1 of 1 EO-4696-511-000 Rev. A版 第一頁/共一頁COLOR CHANGER (24 COLOR MAX.) 換色器 (最多24種顏色)WASH 清洗INJECTOR 注射器WASH 清洗PAINT ENABLE 噴漆激活TRIGGER 觸發器BELL WASH 杯頭清洗PAINT 油漆SOLV/AIR 溶劑/空氣AIR 空氣RECOVERY 回收DUMP 排放2K Process Assembly wit

13、h a Regulator Schematic 含調整器的2K工藝組件示意圖EO-4696-517-000 Rev. C4 Sheet 1 of 1 EO-4696-517-000 Rev. C4版 第一頁/共一頁COLOR CHANGER (4 COLOR MAX.) 換色器 (最多四種顏色)INJECTOR WASH 注射器清洗PAINT ENABLE 噴漆激活TRIGGER 觸發器BELL WASH 杯頭清洗CAT 架子DUMP 排放FLUSH 齊平AIR1 空氣1SOLV/AIR 溶劑/空氣WASH 清洗SOL2 溶劑20-500 PSI 0-500 PSIApplicator Int

14、erface 霧化器接口ET-4696-890-001 Rev. A Sheet 1 of 1 ET-4696-890-001 Rev. A版 第一頁/共一頁ORIGIN OF TOOL FRAME 工具坐標系原點BOLT HOLES 螺栓孔FAN 風扇FAN 風扇FACE PLATE 面板TOOL FRAME 工具架EDGE OF BELL CUP 杯頭邊緣SECTION A-A AA截面SCRMO00000277N (6) SCRMO00000277N (6)M6 Craftech Scr. M6 工藝技術螺絲Torque to 1.25 Nm 轉矩至1.25 NmPINLM0050000

15、12S PINLM005000012S工作特征備注最高運行電壓 90kV正常旋轉速度 20到45 kRPM最高旋轉速度* 45 到60 kRPM噴漆正常流速 0到300 cc/min最大流速 500 cc/min正常噴漆應用壓力 90到120 psi最大噴漆應用壓力 150 psi粘度范圍 50到200 cps空氣空氣壓強供應 85 psi min空氣供應過濾: 級別1 按照DIN ISO 8573-1空氣消耗渦輪支承 57 slpm渦輪在60，000 rpm* 119 slpm成形空氣 70到500 slpm密封空氣 0到50 slpm (通常不需要)電氣能量供應 120 v 50/60 H

16、zTube Requirements 管道要求ET-4696-890-002 Rev. B1 Sheet 1 of 1 ET-4696-890-002 Rev. B1版 第一頁/共一頁SECTION A-A A-A截面BRAKE 制動空氣PAINT 油漆管路SPEED 速度BEAR 軸承空氣SEAL 密封空氣TURB 渦輪空氣WASH 清洗NOTES: 注意:1. TUBING SHOULD BE INSTALLED WITH ROBOT IN ZERO POSITION.管道應與機器人一起安裝在零點位置。SECTION B-B B-B截面SLOTTED CHEESE HEAD 槽形奶酪狀頂部

17、MACHINE SCREW 加工螺絲NYLON 6/6 30% SHORT 短的尼龍6/6 30%FIBER GLASS FILLED 玻璃纖維填充Torque to .55 Nm/4.8 In. Lbs. 轉矩至.55 Nm/4.8 In. LbsColor Changer, Pump and Pump Block 換色器，泵和泵座CHANGER-PUMP Rev. A Sheet 1 of 1 換色器-泵 Rev. A版 第一頁/共一頁Air 空氣Solvent 溶劑Solvent Supply Valve 溶劑供應閥門Air Supply Valve 空氣供應閥門Solvent Wash

18、 Line 溶劑清洗管路Pump Flush Valve 泵沖洗閥門Dump Valve 2 排放閥門2Dump Valve 2 排放閥門2Pressure Transducer P/I 壓力傳感器P/IFluid Regulator 流體調整器Reclaim 回收Bell Wash Valve 杯頭清洗閥門Injector Wash Valve 注射器清洗閥門Trigger Valve 觸發器閥門Paint Enable Valve 噴漆激活閥門Gear and Shaft Assembly 齒輪和軸體組件Drive Shaft 驅動軸Drive Gear 驅動齒輪Key 銷子Rear Plate 后板體Dowel (2) 銷子(2)Arbor 柄軸Driven Gear 驅動齒輪Gear Plate 齒輪板Front Plate 前板體Seal (3) 密封(3)Seal Housing 密封套M5x20 Soc. Hd. Scr. M5x20內六角螺絲Torque to 7.9 Nm/ 70 In. Lbs. 轉矩至7.9 Nm/ 70 In. LbsM5x4