電子有限公司產品樣品規格書

1、 深圳市展鴻光電子有限公司 specification(產品規格書)customer : part no : zh03pw-a4-1w project number : zhy110221002 description: 1w white high power led date : 2011-07-5 customer approed(客戶確認)r&d department(開發部)approved(核準)checked(審核)prepared(制定) data sheet zh03系列 features產品特點: applications產品應用:silica package矽膠灌封

2、 street lamp路燈fast start快速啟動 reading lamp臺燈high-intensity高亮度 the view illuminate景觀照明low attenuation低衰減 decorative lighting裝飾照明long life span壽命長 indoor and outdoor lighting室內外照明no radiation、safety環保、安全 the signal show信號顯示energy-saving節能 flashlight手電筒照明 other uses其它用途 （一）opto-electronics(產品光-電參數):(1)a

3、bsolute maximum rating (ta=25)itemsymbolabsolute maximum rating (ta=25)unitblue/green/whitered/yellowforward currentif350350mapeak forward currentifp500500mapower dissipation 350mapd1100800mwreverse voltagevr5velectrostatic discharge(hbm)esd2000vled junction temperat uretj125operating temperaturetop

4、-40 - 80storage temperaturetstg -40 - 150thermal resistance typicalrjs12/wmanual soldering timet5 sec. at 260(max.)s* absolute maximum ratings ta=25.* ifp conditions: pulse width10msec.and duty1/10(2)initial electrical/optical characteristics (ta=25)part no.vf(lm)cct/d(21/2)min.typ.max.zh03pw-a4-1w3

5、.2-3.4v80902800-3000k140° notes:1.tolerance of measurement of forward voltage±0.1v(電壓誤差±0.1v).2.tolerance of measurement of peakwavelength±1.0nm(波長誤差為±1.0nm).3.tolerance of measurement of luminous flux ±10%(光通量誤差為±10%).4.please use together with the radiator while

6、using led! 務請帶上散熱板使用led.5.in the ambient temperature of 60 degrees to use, or attenuation increase! 請儘量在60之環境溫度下使用led，否則衰減加?。?. please do not squeeze hard, collision led surface! 不要擠壓、碰撞led表面。(二)shape dimensions(產品外形尺寸): unit：mmproduct description產品描述：item項目describe描述item項目describe描述chip material晶片質

7、材algainp/ingan磷化鋁鎵銦/氮化銦鎵colloid color膠體顏色transparent無色透明emitter color發光顏色w/r/g/b/ypotting material灌封材料silica矽膠stent color支架顏色white/black白色/黑色lens透鏡材料silica矽膠bonding粘接方式silver epoxy glue銀膠electrode電極材質au-plating/ ag-plating鍍金銅材/鍍銀銅材(三)electrical & optical curves-spectrum（光&電參數曲線）： spectral en

8、ergy distribution（r、g、b、y、w） ifiv curve（r、g、b、y、w） iflm/w curve（r、g、b、y、w）forward voltageforward current curve（r、g、b、y、w） light intensity distributionlight output characteristics of tj room temperature operating life reliability test result常溫點亮信賴性結果(ta=25oc,if=700ma）use ssc circuit board&heat si

9、nk(tj=50oc) 使用ssc帶熱沉電路板(tj=50oc)timehrrelative luminous output%使用結溫在60°度的使用以下，1000hr 2 degradation(1000小時衰減2%)life time graph (使用壽命)使用結溫在60°度的使用以下，50000hr 50 degradation (50000小時衰減50%) 使 用 說 明一、為避免吸潮建議將產品貯存在放有干燥劑的干燥柜中，貯存溫度為：530，濕度：60%hr。二、貯存在溫度較高環境的產品使用前，建議干燥，干燥條件為：100±5/12個小時。三、產品在焊錫

10、后冷卻過程中避免機械壓力和過大震動。四、回焊后不允許快速冷卻。五、禁止焊接在變形pcb板上。六、產品不得接觸水、油、有機溶液。七、產品使用最大溫度值應考慮工作電流大小。八、打開防潮包裝后7天內產品使用完畢。九、重新包裝未使用的產品置防潮袋密封好之后貯存在干燥的地方。十、產品外觀尺寸可更改而不另行通知。十一、防靜電要求：使用產品時，必須戴防靜電環或防靜電手套，所有設備、裝置、機臺必須有效接地。十二、該產品必須配置恒流源驅動。(1) in order to aviod absorption of moisture it is recommended that the products are st

11、ored inthe dry box (or dessicator ) with a dessicant.alternatively the following environment is recommended: storage temperature :5°c30°c humidity:60% hr max.(2) storage in high humidity if the storage conditions are of high humidity the product should be dried befor use. recommended dryin

12、g conditions: 12 hours at 100°c±5°c(3) any mechanical force or any excess vibration should be avoied during the cooling process after soldering.(4) reflow rapid cooling should be avoided.(5) components should not be mounted on distorted printed circuit boards.(6) devices should not be

13、 used in any type of fluid such as water,oil,organic solvents etc. when cleaning is required,ipa should be used.(7) the maximum ambient temperature should be taken into consideration when determining the operating current.(8) devices should be soldered within 7 days after opening the moisture-proof

14、packing.(9) repack unused product in anti-moisture packing,fold to close any opening and store in a dry place.(10) the appearance and specifications of devices may be modified for improvement without notice.(11) esd precautions.static electricity and surge damages leds.it is recommended that wrist bands or anti-electrostatic gloves be