《儀修專業英語》word版

1、.INSTRUMENT SPECIALTY TERM TOOL 工具1. Multimeter n.物萬用表 2. screwdriver 螺絲起子3. long nose plier 尖嘴鉗4. wrench 扳手5. 手電筒 flashlight6. toolbox 工具箱7. bench 工作臺8. vice, clamp 虎鉗 (美作:vise)9. saw 鋸10. electric hand drill 手電鉆11.back saw blade 鋸條12.bow saw 弓鋸13.rcular saw 圓鋸 (美作:buzzsaw)pass saw, scroll saw 鋼絲鋸1

2、5.file 銼16.ruler 尺17.tape measure 卷尺18.folding ruler 折尺19.vernier caliper 游標卡尺20. resistance box電阻箱21.signal generator信號發生器22.megameter 搖表23.current generator 電流發生器24.sandpaper, emery paper 砂紙25.spanner 扳子 (美作:wrench)26.double-ended spanner 雙頭扳子27.adjustable spanner, monkey wrench 活扳子,活絡扳手28.box spa

3、nner 管鉗子 (美作:socket wrench)29shears 剪子30.wire cutters 剪線鉗31.hacksaw 鋼鋸32.soldering iron 焊鐵,烙鐵33.electric drill, power drill 電鉆34.oxygen weld 氧氣焊接, 氣焊35.screwdriver螺絲刀.IN COMMON USE MATERIAL常用材料36.保險管 protective tube （fuse）37.rivet 鉚釘38.screw 螺絲釘39.nut 螺母40.locknut 自鎖螺母,防松螺母41.bolt 螺栓42.pin, peg, dow

4、el 銷釘43.washer 墊圈44.活接頭 Tie-in45.壓力表接頭 pressure gauge tie-in 46.不銹鋼管 stainless steel pipe 47紫銅管 red cooper pipe48.閘閥 Gate valve49.截止閥 stop valve50球閥 ball valve 51.黑膠布 Black rubberized fabric52.白膠布 White rubberized fabric53.白布帶 White cloth tape54.透明膠帶 scotch tape (adhesive tape)55.平行線 Equal wire,para

5、llel56.多功能電源插座More functionelectrical outlet57.焊錫絲 soldering tin wire58.塑料帶 Plastic tape59.四氟帶 F.T.P.E tape60.毛刷 Brush61.螺紋松動劑 Screw loosening agent 62.粘合劑 Agglutinate glue63.膠水 GluewaterIN COMMON USE TERM 常用術語64.電磁閥, 電磁活門solenoid value65.pressure壓力66.flow流量67.temperature 溫度68.液位 level69.變送器 transdu

6、cer70.繼電器 rely71.孔板 orifice72.定位器 localizer 、positioner73.熱電偶 thermocouple74.熱電阻 Resistance Temperature Detector(RTD)75.三閥組 Manifold valve 76.控制閥 control valve77.量程 range78.零位 zero79.壓力開關 erlock 連鎖81.趨勢 trend82.趨勢記錄 trendline record83.alarm record 報警記錄84.自動 automatic85.手動 manual8

7、6.調整 adjust87.參數 parameter88.檢查 check89.氣動 pneumatic90.故障 fault 、failure91.停車 shut down92.顯示 display93.位移 displacement94.振動 vibration95.組態 configuration96.電/氣 electric pneumatic convertor97.測量 measure98正壓閥 positive valve99負壓閥 negative valve100.通訊 communication常用語句 IN COMMON USE SENTENCE 裝探頭調整至合適位置Ad

8、just probe and justify it to a good position 拆卸檢查控制閥 Demount and check control valve 拆除探頭以免損壞 Demount probe to avoid demage 拆卸閥門定位器，校驗控制閥 Demount valve positioner , calibrate control valve. 測量熱電偶的輸出毫伏制 Check thermocouple output millivolt 打開引壓閥 Open instrument pressure first valve 關閉引壓閥Close instrume

9、nt pressure first valve 打開正壓閥 Open positive valve 打開負壓閥 Open negative valve10.關閉正壓閥 Close positive valve11.關閉負壓閥 Close negative valve12. 打開平衡閥 Open balance valve13. 打開放空閥Open exhaust valve14.灌隔離液Filling sealing liquid15.測量熱電阻的阻值 Check RTD output resistance16.檢查儀表零位 Check instrument zero position17.檢

10、查信號線的通斷、絕緣 Check signal wire through or break and insulation.18.控制閥盤根漏，加盤根 The sealing carrier of Control valve leakage, add packing19控制閥不動作，檢查執行機構 When control valve cant act,check actuating mechanism20.閥位變送器輸出線性不好，調整零位及量程 Valve transducer output is nonlinear, adjust zero and range.21.引壓閥漏，更換引壓閥 In

11、strument pressure first valve leakage ,change it.22.平衡三閥組，檢查儀表零位 Balancing manifold valve,check instrument zero.23.調出歷史記錄，查看趨勢記錄 Open history record , examine tendency chart.24.系統報警，按確認鍵并檢查處理。 System alrm, press acknowledgement key ,check problem and treat.25.液位指示偏低，檢查變送器 Level transmitter indicatio

12、n is lower,check it.26.溫度指示跑零下，檢查熱偶是否接地， Temperature transmitter indication under zero,check it.27.潤滑油油壓低，引起壓縮機跳閘。 Lube oil pressure is lower,so compressor shutdown28.壓縮機軸溫高，檢查并處理。Compressor shaft temperature is high ,check and treat.29.變送器指示不準，需重新校驗 Transmitter indication isnt right, needed anew ca

13、libration.30.用手操器對智能變送器進行參數設定。 Use communication HART writing parameter in intelligent transmitter.31.儀表引壓管線打沖洗油 Washing instrument pressure pipe with oil.32.儀表引壓管線堵 Instrument pressure pipe was jammed . 33.引壓線凝，儀表指示偏低The object in instrument pressure pipe was coagulated, instrument indication is lo

14、w.34.信號線接線端子可能接觸不良。 Signal wire terminal is possible contact defective.35.檢查儀表供電是否正常。 Check instrument power supply whether its normal.36. 檢查儀表氣源是否正常。Check instrument air supply whether its normal37.開機前，必須做連鎖實驗 Before start compressor, we must have interlock test38.處理參與連鎖的儀表時，必須先摘除連鎖。 When we dispos

15、e instrument that is concerned with interlock, we must release interlock at first.39.控制卡件故障，經檢查已損壞，更換。 Cotrol module has a failure, after checking it has bad and change it.40.壓縮機軸振動偏高，檢查探頭是否松動。 Compressor shaft vibration is high,check probe whether it become loose41.調整PID參數，使控制閥保持平穩。 Adjust PID para

16、meter, made control valve holding stabilization.42.小心，不要損壞密封墊片。 Be careful ,dont destroy sealing gasket.43.測量值超程，更改量程范圍。 Measure value over range, change measure range.44. 控制閥跑位，重新校驗。 Control valve lost its position, needed anew calibration45.電液滑閥報警，檢查處理。 Electro- hydraulic slide valve alarm,check and treat.46. 閥位回訊開關接觸不良，處理。 Conrtol valve position switch contact isnt good ,treat it.47.校驗壓力開