合肥學院建筑工程系ansys資料基礎篇

1、“有限元分析及應用”本科生課程有限元分析軟件ANSYS上 機 指 南合肥學院建筑工程系2012年9月說 明 本有限元分析軟件ANSYS上機指南由*老師組織編寫，由*執筆, 于2012年9月完成，基本操作指南中的所有算例都在相應的軟件系統中進行了實際調試和通過。 本上機指南的版權*所有，未經同意，任何單位和個人不得翻印。聯系人：*目 錄Project1 簡支梁的變形分析.1Project2 壩體的有限元建模與受力分析.3Project3 受內壓作用的球體的應力與變形分析.5Project4 受熱載荷作用的厚壁圓筒的有限元建模與溫度場求解.7Project5 超靜定桁架的有限元求解.9Projec

2、t6 超靜定梁的有限元求解.11Project7 平板的有限元建模與變形分析 13Project1 梁的有限元建模與變形分析計算分析模型如圖1-1 所示, 習題文件名: beam。NOTE:要求選擇不同形狀的截面分別進行計算。圖1-1梁的計算分析模型梁截面分別采用以下三種截面（單位：m）： 矩形截面： 圓截面： 工字形截面：B=0.1, H=0.15 R=0.1 w1=0.1，w2=0.1，w3=0.2, t1=0.0114，t2=0.0114，t3=0.0071.1 進入ANSYS程序 ANSYSED 6.1 Interactive change the working directory

3、into yours input Initial jobname: beamRun1.2設置計算類型 ANSYS Main Menu: Preferences select Structural OK1.3選擇單元類型ANSYS Main Menu: Preprocessor Element TypeAdd/Edit/Delete Add select Beam 2 node 188 OK (back to Element Types window) Close (the Element Type window)1.4定義材料參數ANSYS Main Menu: Preprocessor Ma

4、terial Props Material Models Structural Linear Elastic Isotropic input EX:2.1e11, PRXY:0.3 OK1.5定義截面ANSYS Main Menu: Preprocessor Sections Beam Common Sectns 分別定義矩形截面、圓截面和工字形截面：矩形截面:ID=1,B=0.1，H=0.15 Apply 圓截面：ID=2,R=0.1 Apply 工字形截面：ID=3,w1=0.1，w2=0.1，w3=0.2，t1=0.0114，t2=0.0114，t3=0.007 OK 1.6生成幾何模型

5、ü 生成特征點 ANSYS Main Menu: Preprocessor Modeling Create Keypoints In Active CS 依次輸入三個點的坐標：input:1(0,0),2(10,0),3(5,1) OKü 生成梁ANSYS Main Menu: Preprocessor Modeling Create Lines lines Straight lines 連接兩個特征點，1(0,0),2(10,0) OK1.7 網格劃分 ANSYS Main Menu: Preprocessor Meshing Mesh Attributes Picked

6、 lines OK 選擇: SECT:1（根據所計算的梁的截面選擇編號）；Pick Orientation Keypoint(s):YES拾?。?#特征點(5,1) OKMesh Tool Size Controls) lines: Set Pick All(in Picking Menu) input NDIV:5 OK (back to Mesh Tool window) Mesh Pick All (in Picking Menu) Close (the Mesh Tool window)1.8 模型施加約束ü 最左端節點加約束ANSYS Main Menu: Solution

7、 Define Loads Apply Structural Displacement On Nodes pick the node at (0,0) OK select UX, UY,UZ,ROTX OKü 最右端節點加約束ANSYS Main Menu: Solution Define Loads Apply Structural Displacement On Nodes pick the node at (10,0) OK select UY,UZ,ROTX OKü 施加y方向的載荷ANSYS Main Menu: Solution Define Loads App

8、ly Structural Pressure On Beams Pick All VALI:100000 OK1.9 分析計算 ANSYS Main Menu: Solution Solve Current LS OK(to close the solve Current Load Step window) OK1.10 結果顯示 ANSYS Main Menu: General Postproc Plot Results Deformed Shape select Def + Undeformed OK (back to Plot Results window) Contour Plot N

9、odal Solu select: DOF solution, UY, Def + Undeformed , Rotation, ROTZ ,Def + UndeformedOK1.11 退出系統 ANSYS Utility Menu: File Exit Save EverythingOKProject2 壩體的有限元建模與應力應變分析計算分析模型如圖2-1 所示, 習題文件名: dam。圖21 壩體的計算分析模型2.1 進入ANSYS程序 ANSYSED 6.1 Interactive change the working directory into yours input Initia

10、l jobname: damRun2.2設置計算類型 ANSYS Main Menu: Preferences select Structural OK2.3選擇單元類型ANSYS Main Menu: Preprocessor Element TypeAdd/Edit/Delete Add select Solid Quad 4node 42 OK (back to Element Types window) Options select K3: Plane Strain OKClose (the Element Type window)2.4定義材料參數ANSYS Main Menu: P

11、reprocessor Material Props Material Models Structural Linear Elastic Isotropic input EX:2.1e11, PRXY:0.3 OK2.5生成幾何模型ü 生成特征點ANSYS Main Menu: Preprocessor Modeling Create Keypoints In Active CS 依次輸入四個點的坐標：input:1(0,0),2(10,0),3(1,5),4(0.45,5) OKü 生成壩體截面ANSYS Main Menu: Preprocessor Modeling

12、Create Areas Arbitrary Through KPS 依次連接四個特征點，1(0,0),2(10,0),3(1,5),4(0.45,5) OK2.6 網格劃分ANSYS Main Menu: Preprocessor Meshing Mesh Tool(Size Controls) lines: Set 依次拾取兩條橫邊:OKinput NDIV: 15 Apply依次拾取兩條縱邊:OK input NDIV: 20 OK (back to the mesh tool window)Mesh: Areas, Shape: Quad, Mapped Mesh Pick All (

13、in Picking Menu) Close( the Mesh Tool window)2.7 模型施加約束ü 分別給下底邊和豎直的縱邊施加x和y方向的約束ANSYS Main Menu: Solution Define Loads Apply Structural Displacement On lines pick the lines OK select Lab2:UX, UY OKü 給斜邊施加x方向的分布載荷ANSYS 命令菜單欄: Parameters Functions Define/Edit 1) 在下方的下拉列表框內選擇x ,作為設置的變量；2) 在Res

14、ult窗口中出現X,寫入所施加的載荷函數：1000*X； 3) File>Save(文件擴展名：func) 返回：Parameters Functions Read from file：將需要的.func文件打開，任給一個參數名，它表示隨之將施加的載荷OK ANSYS Main Menu: Solution Define Loads Apply Structural Pressure On Lines 拾取斜邊；OK 在下拉列表框中，選擇：Existing table OK 選擇需要的載荷參數名OK2.8 分析計算 ANSYS Main Menu: Solution Solve Curr

15、ent LS OK(to close the solve Current Load Step window) OK2.9 結果顯示 ANSYS Main Menu: General Postproc Plot Results Deformed Shape select Def + Undeformed OK (back to Plot Results window)Contour Plot Nodal Solu select: DOF solution, UX,UY, Def + Undeformed , Stress ,SX,SY,SZ, Def + UndeformedOK2.10 退出系

16、統 ANSYS Utility Menu: File Exit Save EverythingOKProject3 受內壓作用的球體的有限元建模與分析計算分析模型如圖3-1 所示, 習題文件名: sphere。 圖3-1受均勻內壓的球體計算分析模型（截面圖）3.1 進入ANSYS程序 ANSYSED 6.1 Interactive change the working directory into yours input Initial jobname: sphereRun3.2設置計算類型 ANSYS Main Menu: Preferences select Structural OK3.

17、3選擇單元類型ANSYS Main Menu: Preprocessor Element TypeAdd/Edit/Delete Add select Solid Quad 4node 42 OK (back to Element Types window) Options select K3: Axisymmetric OKClose (the Element Type window)3.4定義材料參數ANSYS Main Menu: Preprocessor Material Props Material Models Structural Linear Elastic Isotropic

18、 input EX:2.1e11, PRXY:0.3 OK3.5生成幾何模型ü 生成特征點ANSYS Main Menu: Preprocessor Modeling Create Keypoints In Active CS 依次輸入四個點的坐標：input:1(0.3,0),2(0.5,0),3(0,0.5),4(0,0.3) OKü 生成球體截面ANSYS 命令菜單欄: Work Plane>Change Active CS to>Global Spherical ANSYS Main Menu: Preprocessor Modeling Create

19、Lines In Active Coord 依次連接1,2,3,4點OK Preprocessor Modeling Create Areas Arbitrary By Lines 依次拾取四條邊OK ANSYS 命令菜單欄: Work Plane>Change Active CS to>Global Cartesian3.6 網格劃分ANSYS Main Menu: Preprocessor Meshing Mesh Tool(Size Controls) lines: Set 拾取兩條直邊:OKinput NDIV: 10 Apply拾取兩條曲邊:OK input NDIV:

20、20 OK (back to the mesh tool window)Mesh: Areas, Shape: Quad, Mapped Mesh Pick All (in Picking Menu) Close( the Mesh Tool window)3.7 模型施加約束ü 給水平直邊施加約束ANSYS Main Menu: Solution Define Loads Apply Structural Displacement On Lines 拾取水平邊：Lab2: UY OK， ü 給豎直邊施加約束ANSYS Main Menu: Solution Define

21、Loads Apply Structural Displacement Symmetry B.C. On Lines 拾取豎直邊 OKü 給內弧施加徑向的分布載荷ANSYS Main Menu: Solution Define Loads Apply Structural Pressure On Lines 拾取小圓??；OK input VALUE:100e6 OK 3.8 分析計算 ANSYS Main Menu: Solution Solve Current LS OK(to close the solve Current Load Step window) OK3.9 結果顯示

22、 ANSYS Main Menu: General Postproc Plot Results Deformed Shape select Def + Undeformed OK (back to Plot Results window) Contour Plot Nodal Solu select: DOF solution, UX,UY, Def + Undeformed , Stress ,SX,SY,SZ,Def + UndeformedOK3.10 退出系統 ANSYS Utility Menu: File Exit Save EverythingOKProject4 受熱載荷作用的

23、厚壁圓筒的有限元建模與溫度場求解計算分析模型如圖4-1 所示, 習題文件名: cylinder。 圖4-1受熱載荷作用的厚壁圓筒的計算分析模型（截面圖）4.1 進入ANSYS程序 ANSYSED 6.1 Interactive change the working directory into yours input Initial jobname: cylinder Run4.2設置計算類型 ANSYS Main Menu: Preferences select Thermal OK4.3選擇單元類型ANSYS Main Menu: Preprocessor Element TypeAdd/

24、Edit/Delete Add select Thermal Solid Quad 4node 55 OK (back to Element Types window) Options select K3: Axisymmetric OKClose (the Element Type window)4.4定義材料參數ANSYS Main Menu: Preprocessor Material Props Material Models Thermal Conductivity Isotropic input KXX:7.5 OK4.5生成幾何模型ü 生成特征點ANSYS Main M

25、enu: Preprocessor Modeling Create Keypoints In Active CS 依次輸入四個點的坐標：input:1(0.3,0),2(0.5,0),3(0.5,1),4(0.3,1) OKü 生成圓柱體截面ANSYS Main Menu: Preprocessor Modeling Create Areas Arbitrary Through KPS 依次連接四個特征點，1(0.3,0),2(0.5,0),3(0.5,1),4(0.3,1) OK4.6 網格劃分ANSYS Main Menu: Preprocessor Meshing Mesh T

26、ool(Size Controls) lines: Set 拾取兩條水平邊:OKinput NDIV: 5 Apply拾取兩條豎直邊:OK input NDIV: 15 OK (back to the mesh tool window)Mesh: Areas, Shape: Quad, Mapped Mesh Pick All (in Picking Menu) Close( the Mesh Tool window)4.7 模型施加約束ü 分別給兩條直邊施加約束ANSYS Main Menu: Solution Define Loads Apply Thermal Temperat

27、ure On Lines 拾取左邊, Value: 500 Apply(back to the window of apply temp on lines) 拾取右邊，Value：100 OK 4.8 分析計算 ANSYS Main Menu: Solution Solve Current LS OK(to close the solve Current Load Step window) OK4.9 結果顯示 ANSYS Main Menu: General Postproc Plot Results Deformed Shape select Def + Undeformed OK (ba

28、ck to Plot Results window)Contour Plot Nodal Solu select: DOF solution, Temperature TEMP OK4.10 退出系統 ANSYS Utility Menu: File Exit Save EverythingOKProject5 超靜定桁架的有限元建模與分析計算分析模型如圖5-1 所示, 習題文件名: truss。 圖51 超靜定桁架的計算分析模型5.1 進入ANSYS程序 ANSYSED 6.1 Interactive change the working directory into yours input

29、 Initial jobname: trussRun5.2設置計算類型 ANSYS Main Menu: Preferences select Structural OK5.3選擇單元類型ANSYS Main Menu: Preprocessor Element TypeAdd/Edit/Delete Add select Link 2D spar 1 OK (back to Element Types window) Options select K3: Plane Strain OKClose (the Element Type window)5.4定義材料參數ANSYS Main Men

30、u: Preprocessor Material Props Material Models Structural Linear Elastic Isotropic input EX:2.1e11, PRXY:0.3 OK5.5定義實常數 ANSYS Main Menu: Preprocessor Real Constants Add select Type 1 OKinput AREA:0.25 OK Close (the Real Constants Window)5.6生成幾何模型ü 生成特征點ANSYS Main Menu: Preprocessor Modeling Cre

31、ate Keypoints In Active CS 依次輸入四個點的坐標：input:1(1,1),2(2,1),3(3,1),4(2,0) OKü 生成桁架ANSYS Main Menu: Preprocessor Modeling Create Lines Lines Straight Line 依次連接四個特征點，1(1,1),2(2,1),3(3,1),4(2,0) OK5.7 網格劃分ANSYS Main Menu: Preprocessor Meshing Mesh Tool(Size Controls) lines: Set 依次拾取三根桿:OKinput NDIV:

32、 1 OK (back to the mesh tool window)Mesh: lines Mesh Pick All (in Picking Menu) Close( the Mesh Tool window)5.8 模型施加約束ü 分別給1,2,3三個特征點施加x和y方向的約束ANSYS Main Menu: Solution Define Loads Apply Structural Displacement On Keypoints 拾取1(1,1),2(2,1),3(3,1)三個特征點 OK select Lab2:UX, UY OKü 給4#特征點施加y方向

33、載荷ANSYS Main Menu: Solution Define Loads Apply Structural Force/Moment On Keypoints 拾取特征點4(2,0) OK Lab: FY, Value: -100e6 OK5.9 分析計算 ANSYS Main Menu: Solution Solve Current LS OK(to close the solve Current Load Step window) OK5.10 結果顯示 ANSYS Main Menu: General Postproc Plot Results Deformed Shape se

34、lect Def + Undeformed OK (back to Plot Results window) Contour Plot Nodal Solu select: DOF solution, UY, Def + Undeformed OK5.11 退出系統 ANSYS Utility Menu: File Exit Save EverythingOKProject6 超靜定梁的有限元建模計算計算分析模型如圖6-1 所示, 習題文件名: statically indeterminate beam 圖61 超靜定梁的計算分析模型6.1 進入ANSYS程序 ANSYSED 6.1 Inte

35、ractive change the working directory into yours input Initial jobname: statically indeterminate beamRun6.2設置計算類型 ANSYS Main Menu: Preferences select Structural OK6.3選擇單元類型ANSYS Main Menu: Preprocessor Element TypeAdd/Edit/Delete Add select Beam tapered 44 OK(back to Element Types window) Close (the

36、Element Type window)6.4定義材料參數ANSYS Main Menu: Preprocessor Material Props Material Models Structural Linear Elastic Isotropic input EX:2.1e11, PRXY:0.3 OK6.5定義截面ANSYS Main Menu: Preprocessor Sections Beam Common Sectns 定義矩形截面:ID=1,B=0.01,H=0.1 OK 6.6生成幾何模型ü 生成特征點 ANSYS Main Menu: Preprocessor M

37、odeling Create Keypoints In Active CS 依次輸入三個點的坐標：input:1(0,0),2(1,0),3(2,0),4(0,0,1) OKü 生成梁ANSYS Main Menu: Preprocessor Modeling Create Lines lines Straight lines 依次連接三個特征點，1(0,0), 2(1,0),3(2,0) OKü 顯示梁體ANSYS命令菜單欄：PlotCtrls >Style >Size and Style /ESHAPE On OK6.7 網格劃分 ANSYS Main Me

38、nu: Preprocessor Meshing Mesh Attributes Picked lines OK 拾取: SECT:1；Pick Orientation Keypoint(s):YES拾?。?#特征點(0,0,1) OKMesh Tool (Size Controls) lines: Set Pick All(in Picking Menu) input NDIV:8 OK (back to Mesh Tool window) Mesh Pick All (in Picking Menu) Close (the Mesh Tool window)6.8 模型施加約束ü

39、 分別給1,2,3三個特征點加約束ANSYS Main Menu: Solution Define Loads Apply Structural Displacement On Keypoints 拾取1,2,3 keypoints OK select All DOF OKü 施加y方向的載荷ANSYS Main Menu: Solution Define Loads Apply Structural Pressure On Beams Pick All LKEY:2,VALI:100000 OK6.9 分析計算 ANSYS Main Menu: Solution Solve Cur

40、rent LS OK(to close the solve Current Load Step window) OK6.10 結果顯示 ANSYS Main Menu: General Postproc Plot Results Deformed Shape select Def + Undeformed OK (back to Plot Results window) Contour Plot Nodal Solu select: DOF solution, UY, Def + Undeformed , Rotation, ROTZ ,Def + UndeformedOK6.11 退出系統

41、ANSYS Utility Menu: File Exit Save EverythingOKProject7 平板的有限元建模與變形分析計算分析模型如圖7-1 所示, 習題文件名: plane 圖71 受均布載荷作用的平板計算分析模型7.1 進入ANSYS程序 ANSYSED 6.1 Interactive change the working directory into yours input Initial jobname: planeRun7.2設置計算類型 ANSYS Main Menu: Preferences select Structural OK7.3選擇單元類型ANSYS Main Menu: Preprocessor Element TypeAdd/Edit/Delete Add select Solid Quad 4node 42 OK (back to Element Types window) Options select K3: Plane stress w/thk OKClose (the Element Type window)7.4定義材料參數ANSYS