新版輪機英語unit25Anchorwindlassand-PPT課件_第1頁
新版輪機英語unit25Anchorwindlassand-PPT課件_第2頁
新版輪機英語unit25Anchorwindlassand-PPT課件_第3頁
新版輪機英語unit25Anchorwindlassand-PPT課件_第4頁
新版輪機英語unit25Anchorwindlassand-PPT課件_第5頁
已閱讀5頁,還剩50頁未讀 繼續免費閱讀

下載本文檔

版權說明:本文檔由用戶提供并上傳,收益歸屬內容提供方,若內容存在侵權,請進行舉報或認領

文檔簡介

1、Lesson 25 Anchor windlass and Mooring winch 錨機和絞纜機 Anchor handling equipment The windlass(錨機) is the usual anchor handling device where one machine may be used to handle both anchor . A more recent development , particularly on large vessels, is the split windlass where one machine is used for each

2、anchor.One unit of a split windlass(分離式錨機) is shown in Fig.25-1.The rotating units consist of a cable lifter(錨鏈輪) with shaped smug(凸起) to grip the anchor cable(錨鏈), a mooring drum(絞纜筒) for paying out(放松) or letting go(放出) of mooring wires and a warp end for warping duties.Each of these units maybe s

3、eparately engaged(嚙合) or disengaged by means or a dog clutch(牙嵌離合器) ,although the warp end is often driven in association with the mooring drum. A spur gear(正齒輪) assembly transmits the motor drive to shaft where the various dog clutches enable the power take-off . Separate band brakes(獨立式剎車) are fit

4、ted hold the cable lifter and the mooring drum(絞纜筒) when the power is switched off.The cable lifter unit(錨鏈輪) , show in Fig.25-1, is mounted so as to raise and lower the cable from the spurling pipe(錨鏈管) ,which is at the top and center of the chain or cable locker(錨鏈艙) . Details of the snugs(卡塊) use

5、d to grip the cable and band brake(帶式剎車) can be seen. Anchor capstans(起錨絞盤) are used in some installations where the cable lifter rotates about a vertical axis. Only the cable lifter unit is located on deck ,the driving machinery(驅動機械) being on the deck below . A warping end or barrel may be driven

6、by the same unit and is positioned near the cable lifter.The efficient working of the anchor windlass is essential to the safety of the ship . An anchor windlass can expect to fulfill(滿足) the following: 1.The windlass cable lifter brakes must be able to control the running anchor and cable when the

7、cable lifter is disconnected from the gear during “l(fā)etting go”(放錨).Average cable speeds vary between 5-7 m/sec during this operation2.The windlass must be able heave a certain weight of cable at a specified speed(額定轉速) . This “full load” duty of the windlass varies but is commonly between 4 and 6 ti

8、mes the weight of one anchor ,the speed of haul being at least 9 m/min up to 15 m/min.3.The braking effort(剎車效果) obtained at the cable lifter must be at least equal to 40 percent of the breaking strength of the cable . Most anchor handing equipments incorporate(包含) warp ends for mooring purposes(系泊)

9、 and line speeds of up to 0.75 to 1.00 m/sec are required . The most conventional types of equipment in use are as follows.WindlassesThis equipment is self-contained (獨立的)and normally one prime mover drives two cablelifters and two warp ends(絞纜端), the latter may not be declutchable(離合裝置) and ,if so,

10、 rotate when the cablelifters are engaged.There is some variation in detail design of cable lifters and in their drives. Due to the low speed of rotation required of the cablelifter whilst heaving anchor, (345r/min) a high gear reduction (齒輪減速機構) is needed when the windlass is driven by a high speed

11、 electric of hydraulic motor.This is generally obtained by using a high ratio worm gear(渦輪) followed by a single step of spur gears(單級正齒輪) between the warpend shaft and cablelifters.Alternatively, multi steps of spur gears are used.Capstans(起錨機) with this type of equipment the driving machinery is s

12、ituated below deck and the cablelifters are mounted horizontally being driven by vertical shafts.Mooring winchesMooring winches provide the facility for tensioning the wire up to the stalling capacity(堵轉轉矩) of the winch(絞車), usually 1.5 times full load(全負荷), thereafter the load is held(握持) by the pr

13、ime mover brake or barrel brake when the power is shut off.The winch cannot pay out wire unless the brake is overhauled(超越) or recover wire unless manually operated, thus wires may become slack.The majority of automatic mooring winches(自動系纜機) are spur geared(正齒輪) to improve the backward efficiency o

14、f the gear train for rendering, the gearing(齒輪機構) and bearings being totally enclosed and lubricated from the oil sump.On larger mooring winches where a barrel brake is fitted, it is now common practice to design the brake to withstand the breaking strength of the mooring wire.Worm geared(渦輪蝸桿) auto

15、matic mooring winches are uncommonas the multistart(多次起動) feature required to improve gear efficiency reduces the main advantage of the worm gear i.e the high gear ratio(傳動比較高).Winches with various arrangements of barrels are the usual mooring equipment used on board ships . A mooring winch is Fig.2

16、5-2 where the various parts can be identified. The winch barrel or drum is used for hauling(收緊) in or letting out the wires or ropes which will fasten the ship to the shore. The warp end is used when moving the ship using ropes or wires fastened to bollards(系纜樁) ashore and wrap around the warpend of

17、 tile winch.The construction of a mooring winch will now be examined, again with respect to Fig.25-2.The motor drive is passed through a spur gear transmission(直齒輪傳動機構), a clutch and thus to the drum(卷筒) and warp end.A substantial(堅實的) frame supports the assembly and a band brake is used to hold the drum when required.The control arrangements for the drive motor permit forward or reverse rotation together with a selection of speeds during operation.Modern mooring winches are arranged as automatic self tensioning units(自動張緊裝置).The flow of the tides(潮) or chan

溫馨提示

  • 1. 本站所有資源如無特殊說明,都需要本地電腦安裝OFFICE2007和PDF閱讀器。圖紙軟件為CAD,CAXA,PROE,UG,SolidWorks等.壓縮文件請下載最新的WinRAR軟件解壓。
  • 2. 本站的文檔不包含任何第三方提供的附件圖紙等,如果需要附件,請聯系上傳者。文件的所有權益歸上傳用戶所有。
  • 3. 本站RAR壓縮包中若帶圖紙,網頁內容里面會有圖紙預覽,若沒有圖紙預覽就沒有圖紙。
  • 4. 未經權益所有人同意不得將文件中的內容挪作商業或盈利用途。
  • 5. 人人文庫網僅提供信息存儲空間,僅對用戶上傳內容的表現方式做保護處理,對用戶上傳分享的文檔內容本身不做任何修改或編輯,并不能對任何下載內容負責。
  • 6. 下載文件中如有侵權或不適當內容,請與我們聯系,我們立即糾正。
  • 7. 本站不保證下載資源的準確性、安全性和完整性, 同時也不承擔用戶因使用這些下載資源對自己和他人造成任何形式的傷害或損失。

最新文檔

評論

0/150

提交評論