12V60Ah-磷酸鐵鋰電池產品規格書

儲能型磷酸鐵鋰電池規格書STORAGE LiFePO4 BATTERY SPECIFICATIONS客戶名稱(Customer)： 產品型號(Type)： CF12V60Ah 發行日期(Issuing Date)： Prepared制定 Checked審核 Approved批準 地址(Address)：東莞市南城區新基大道新基大廈310 電話(Tel)：0769- 傳真(Fax)：0769- 郵箱(E-mail)：網址(Website)：1. 適用范圍(Product Scope)本規格書描述了由東莞市池能電子科技有限公司生產的鋰離子二次電池的技術要求、測量方法、運輸、儲存及注意事項。This Specification describes the requirements of the lithium ion rechargeable battery supplied by Dongguan Chineng Electronic Technology Co.,Ltd.2. 電池組特性 (Battery Group Specifications) Cell電芯Model 規格型號IFP-10AhCapacity 容量10 AhRated Voltage 標稱電壓3.2 VInternal Resistance 內阻標準4 mCombination Standard 配組標準A. 容差Capacity Difference1% B. 內阻Resistance()=12 m C. 荷電保持能力Current-maintaining Ability90% D. 電壓Voltage3.33.4VCombination Method 組合方式4串6并 4S 6PPile Index成品參數Rated Capacity 標稱容量60.0Ah Minimal Capacity 最小容量（0.3C5A）60.0AhNominal Voltage 額定電壓12.0VMax. Charge Voltage 最大充電電壓14.8 VDischarge cut-off voltage 放電截止電壓10.0VCharge Current充電電流5-10AWorking Current 工作電流10AOutput and Input輸出端與輸入端P+(red) / P-(black)Weight 電池重量 7.2KgDimension 外形尺寸（LWH）168260100mm(不包含外露開關)Charge Method適用充電Standard 標準5A16hrsQuick 快速10A6hrs. Operating Temperature 適用溫度Charge充電045；32oF113oFDischarge放電-2060；-4oF149oFManagement system 管理系統Single cell over-charge cut-off voltage單只過壓保護值3.9V Charge Working voltage過壓釋放值3.8VSingle cell under-discharge cut-off voltage單只欠壓保護值2.3VDischarge working voltage欠壓釋放值2.7VConditions of over-charge and under-discharge voltage recovery過、欠壓恢復條件With the high-point voltage reaching the working voltage 極限電壓達到釋放值Over-charge cut-off current 過流保護值40AShort-circuit protection 短路保護Own this ability 具備此功能Condition for the recovery of over-current and short-circuit protection 過流短路保護恢復條件Cut the circuit to automatic recovery 斷開負載自動恢復單只電芯曲線圖feature curve for single cell3. 技術要求 (Technical Requirements)3.1測試條件(除特別規定) Testing Conditions (unless otherwise specified) 溫 度Temperature: 1535相對濕度Relative Humidity: 45%75%大氣壓Atmospheric pressure: 86106Kpa3.2充放電性能 (Electrical Characteristics)NO項目(ITEM)測試方法(Testing Instruction)要求(Requirements)1Standard Charge標準充電Charging the cell initially with constant current at 0.5C and then with constant voltage at 3.7V till charge current declines to 0.05C先用0.5C恒流充電至3.7V，再恒壓3.7V充電直至充電電流0.05C2Rated Capacity初始容量Measure discharge capacity with discharge current 1C to 2.5V cut-off within 1 hour after standard charge.標準充電方式充電后，以1C電流放電至2.5V的容量60Ah3Cycle Life循環壽命Measure the capacity after 2000 cycles of standard charge and discharge at 1C current to 2.50V cut-off 標準充電方式充電后，1C放電至2.50V，如此循環2000次后電池的剩余容量 80% of Rated Capacity初始容量的80%4Storage Characteristics 儲存性能Capacity after 30days storage at 25 from standard charge標準充電方式充電后，25下儲存30天后的容量Retention capacity90%剩余容量90%Capacity after 7days storage at 60 from standard charge標準充電方式充電后，60下儲存7天后的容量Recovery capacity 90%剩余容量90%3.3環境性能 (Environmental Characteristic) NO項目(ITEM)測試方法(Testing Instruction)要求(Requirements)1Temperature testing高低溫測試Measure capacity with constant discharge current 0.5C to 2.5V cut-off at each temperature after standard charge at 25, Percentage as an index of the capacity compared with 100% at 2525下標準充電方式充電后，在指定溫度下0.5C放電至2.5V的容量，并以25時放電容量為基準計算百分率70% at 0100% at 2596% at 602Constant temperature /humidity恒定濕熱性能Keep the battery at 40 and 90%RH for 96hrs將電池放入溫度為40，相對濕度為90%的條件下擱置96小時Recovery capacity 85%恢復容量85%3.4機械性能 (Mechanical characteristics)NO項目(ITEM)測試方法(Testing Instruction)要求(Requirements)1Vibration振動After standard charge, fixed the cell to vibration table and subjected to vibration cycling that the frequency is to be varied at the rate of 1Hz per minute between 10Hz 55Hz, the excursion of the vibration is 1.6mm.The cell shall be vibrated for 30 minutes per axis of XYZ axes. 將標準充電后的電芯固定在振動臺上，沿X、Y、Z三個方向各振動30分鐘，振幅1.6 mm，振動頻率為10Hz55Hz，每分鐘變化為1Hz。The battery shall not rupture, smoke, catch fire, vent or leak and the voltage not be lower than 2.5V電池應無破裂、冒煙、著火、泄漏或漏液，并且電壓不低于2.5V2IFPacting Testing碰撞After vibration , the battery will be IFPacted 100010 times(6020 times per minute) with the acceleration of 100 m/s2 and pulse lasting time 16ms. 將振動后的電池以峰值加速度為100 m/s2的脈沖撞擊100010次(平均每分鐘6020次)，脈沖持續時間為16ms3Free fall自由跌落After IFPacting, the battery will be dropped free five times in three mutually perpendicular directions from the height of 1.0m onto a hard board with the thickness of 20mm碰撞實驗結束后，將電池由高度為1m的位置自由跌落到置于水泥地面上的20mm厚的硬木板上，從X、Y、Z正負方向（六個方向）每個方向自由跌落1次3.5安全性能 (Safe Characteristic)NO項目(ITEM)測試方法(Testing Instruction)要求(Requirements)1Short Circuit短路After standard charge，the battery located in a fume hood is to be short-circuited by connecting the positive and negative terminals with an external load of less than 50 m till the battery case temperature has returned to near ambient temperature.將標準充電后的電池置于通風櫥中，短路其正負極（線路總電阻不大于50mV），實驗過程中監視電池溫度變化，當電池溫度下降到接近初始室溫時，結束實驗The battery shall not rupture, smoke, catch fire, vent or leak.電池應無破裂、冒煙、著火、泄漏或漏液2Abnormal Changing Test 過充After discharge to 2.5V cut-off with discharge current 1C, the battery is to be subjected to a charging current 3C.The specified charging current is to be obtained by connecting a resistor of the specified size and rating in series with the battery. The test time is to be calculated using the formula: tc=2.5c/3(Ic) 將電池1C放電至2.5V后，調節電流3C充電，充電時間按以下公式計算：tC = 2.5*電池額定容量/(3*制造商給定1C電流)3Over discharge testing過放After standard charge, the battery will be connected with external with a maximum resistance load of 0.1 for 24hrs until it is completely discharged and the battery case temperature has returned to near ambient temperature.以標準方式充電后，將電池正負端以內阻小于0.1歐姆的銅導線連接24小時.，直至電池完全放電，溫度下降到環境溫度4Puncture穿刺After standard charge，the battery located in a fume hood is to be punctured with a nail (diameter1mm) until it is completely discharged and the battery case temperature has returned to near ambient temperature將標準充電后的電池置于通風櫥中，用直徑不小于1mm的針將電池從正面刺穿，直至電池完全放電，溫度下降到環境溫度4 電池組基本性能 (Basic Characteristics of Battery) 2.1電池型號Battery Type4S6P IFP2.2外殼材質Material of Case環氧樹脂Epikote2.3額定電壓Nominal Voltage12.0 V2.4額定容量Nominal Capacity60Ah(0.2C)2.5內阻Internal Resistance400 mW2.6放電截止電壓Discharge Cut-off Voltage10.0V2.7最大充電電流Max Charge Current10A2.8最大放電電流Max Discharge Current10A2.9最大充電電壓Max Charge Voltage14.8V2.10充電方法Charge methodCC/CV (constant current/constant voltage)CC/CV (恒流恒壓)2.11尺寸Dimension長度Thickness: 260mm 寬度Width: 168 mm高度Height: 100 mm2.12重量Weight約：7.2Kg About: 7.2Kg5 電池組保護功能要求 (Battery Required Protection Functions)To insure the safety, charger and the protection circuit shall be satisfied the items below. As safety device, please use in combination with the temperature fuse. The standard charge method is CC/CV (constant current/constant voltage)為確保安全,充電器和保護電路應符合以下要求。同時請使用裝有熱熔保險絲的安全裝置。標準充電方法為CC/CV(恒流/恒壓)5.1 參數(product Specification)名 稱(NAME)項 目(ITEM)值 (value)精度（Precision）單 位(unit)過充電壓(Over voltage)過充檢測電壓 Ocv390025mV過充恢復電壓 Vcl380050mV延遲Delay Time10.5S過放電壓(Under Voltage)過放檢測電壓 Vcu230080mV過放恢復放電 Vcl2700100mV延遲Delay Time10050mS充電電流(Charge Current)充電電流OC16A過流延遲OC Delay Time1000100mS工作電流(Current)持續放電電流（Continuous Output Discharging Current）20A過放電流(Over Current)過放保護電流OC605A過流延遲OC Delay Time105mS靜態電流(Current Consumption)工作狀態 Normal Mode30uA休眠狀態 Sleep Mode0.1uA短路(Short Circuit)短路電流 SC600150A延遲 Delay Time1000uS恢復條件Recovery Condition斷開負載Manual regulation6 保質期限及產品責任WARRANTY PERIOD & PRODUCT LIABILITYWarranty period of this product is 24 months from manufacturing code.保質期是從出廠日期(噴碼)開始起二十四個月.Chineng Electronic Technology Co.,Ltd. is not responsible for the troubles caused by mishandling of the battery which is clearly against the instructions in this specification. 池能電子科技有限公司對因沒有按本規格書規定操作而導致的意外不負責任When Chineng Electronic Technology Co.,Ltd. finds any new facts CHINENG require modification of this document, we will inform you again. 一旦池能電子科技有限公司發現本規格書有新的修改細節，我們將再告知。7 包裝電池上的標示INDICATIONS ON BATTERY PACKThe following warnings should be indicated on the battery packs.以下警告應注明在包裝后的電池上 Use a specified charger. 使用規定的充電器 Do not throw the battery into fire, or heat. 不要將電池投入火中或加熱 Do not short-circuit the battery terminals 不要將電池兩端短路 Do not disassemble the battery. 不要將電池分解拆散8 電池使用時警告事項及注意事項WARNINGS AND CAUTIONS IN HANDLING THE Lithium-ion BATTERY To prevent a possibility of the battery from leaking, heating or explosion please observe the following precautions:為防止電池可能發生泄漏,發熱、爆炸,請注意以下預防措施：WARNINGS!1. Do not immerse the battery in water or seawater, and keep the battery in a cool dry surrounding if it stands by. 嚴禁將電池浸入海水或水中,保存不用時,應放置于陰涼干燥的環境中2. Do not use or leave the battery near a heat source as fire or heater 禁止將電池在熱高溫源旁,如火、加熱器等使用和留置3. When recharging, use the battery charger specifically for that purpose 充電時請選用鋰離子電池專用充電器4. Do not reverse the positive (+) and negative (-) terminals 嚴禁顛倒正負極使用電池5. Do not connect the battery to an electrical outlet 嚴禁將電池直接接入電源插座6. Do not discard the battery in fire or heat it 禁止將電池丟于火或加熱器中7. Do not short-circuit the battery by directly connecting the positive (+) and negative (-) terminal with metal objects such as wire. 禁止用金屬直接連接電池正負極短路8. Do not transport or store the battery together with metal objects such as necklaces, hairpins etc. 禁止將電池與金屬,如發夾、項鏈等一起運輸或貯存9. Do not strike or throw the battery 禁止敲擊或拋擲、踩踏電池等10. Do not directly solder the battery and pierce the battery with a nail or other sharp object. 禁止直接焊接電池和用釘子或其它利器刺穿電池CAUTIONS!1. Do not use or leave the battery at very high temperature (for example, at strong direct sunlight or in a vehicle in extremely hot weather). Otherwise, it can overheat or fire or its performance will be degenerated and its service life will be decreased. 禁止在高溫下（炙熱的陽光下或很熱的汽車中）使用或放置電池,否則可能會引起電池過熱、起火或功能失效、壽命減短2. Do not use it in a location where static electricity is great, otherwise, the safety devices may be damaged, causing hidden trouble of safety. 禁止在強靜電和強磁場的地方使用,否則易破壞電池安全保護裝置,帶來不安全的隱患3. If the battery leaks, and the electrolyte get into the eyes. Do not rub eyes, instead, rinse the eyes with clean running water, and immediately seek medical attention. Otherwise, it may injure eyes or cause a loss of sight. 如果電池發生泄露,電解液進入眼睛,請不要揉擦,應用清水沖洗眼睛,并立即送醫院治療,否則會傷害眼睛4. If the battery gives off an odor, generates heat, becomes discolored or deformed, or i