珠海商住建筑施工臨時用電方案（91頁）[優秀工程方案]

1、臨時用電專項施工方案 臨時用電專項施工方案編制人: 編制單位技術負責人: 編制單位(蓋章): 編制日期: 施工臨時用電方案目 錄一、工程概況3二、編制依據3三、施工條件3四、設計內容和步驟51、現場勘探及初步設計:52、確定用電負荷:63、計算電流154、選擇電氣設備16五、繪制臨時供電施工圖80六、安全用電防火措施941、施工現場發生火災的主要原因942、預防電氣火災的措施953、臨時用電組織管理機構96一、工程概況工程名稱:建設單位:監理單位:設計單位:施工單位: .位于珠海市斗門區白蕉鎮虹橋三路南側，總建筑面積為65767.12平方米。其中20XX34層、15、16#樓33層及4棟商業,

2、 住宅樓建筑高度分別為99m、95.60m，商業G5、G(7/9/10)建筑高度分別為10.5m、9m,設地下室1層。結構等級為二級，耐火等級為二級，耐久年限為50年，抗震設防烈度為7度。室內環境控制分類為1類。二、編制依據低壓配電設計規范GB50054-95中國建筑工業出版社建筑工程施工現場供電安全規范GB50194-93中國建筑工業出版社通用用電設備配電設計規范GB50055-93中國建筑工業出版社供配電系統設計規范GB50052-95中國建筑工業出版社施工現場臨時用電安全技術規范JGJ46-20XX中國建筑工業出版社建筑施工安全檢查標準JGJ59-20XX有關建筑施工用電現場管理的安全技

3、術規范和規定等。三確定電源進線、配電室、總配電柜、分配電箱等位置及線路走向1、現已在本工程的東南角安裝一臺400KVA容量的電力變壓器，根據現場平面布置情況，在本工程的東南側設置配電房及一臺100KVA發電機組。2、分配電箱的位置及現場線路走向，主要沿西側圍墻由北向東進行布置，分別設置砼輸送、人貨電梯、塔吊、鋼筋木工加工場、辦公生活區等分配電箱，具體詳見施工現場用電平面布置圖。(P82)三、施工條件施工現場用電量統計表:-序號 機具名稱 型號 安裝功率(kW) 數量 合計功率(kW)1 塔式起重機 50 1 50 2 人 貨 梯 SCD100/100A 11 1 11 3 灰漿攪拌機 UJ32

4、5 3 1 3 4 木工圓鋸 MJ104 3 1 3 5 插入式振動器 ZX35 0.8 3 2.4 6 插入式振動器 ZX25 0.8 2 1.6 7 交流電焊機 BX3-120XX 9 1 9 8 白熾燈 0.01 1 0.01 9 碘鎢燈 0.5 1 0.5 10 人 貨 梯 SCD100/100A 11 1 11 11 灰漿攪拌機 UJ325 3 1 3 12 鋼筋調直機 GT4/14 4 1 4 13 鋼筋彎曲機 GW40 3 1 3 14 鋼筋切斷機 QJ32-1 3 1 3 15 木工圓鋸 MJ104 3 1 3 16 插入式振動器 ZX35 0.8 3 2.4 17 插入式振動

5、器 ZX25 0.8 2 1.6 18 交流電焊機 BX3-120XX 9 1 9 19 白熾燈 0.01 1 0.01 20XX 碘鎢燈 0.5 1 0.5 21 塔式起重機 50 1 50 22 人 貨 梯 SCD100/100A 11 1 11 23 灰漿攪拌機 UJ325 3 1 3 24 鋼筋調直機 GT4/14 4 1 4 25 鋼筋彎曲機 GW40 3 1 3 26 鋼筋切斷機 QJ32-1 3 1 3 27 木工圓鋸 MJ104 3 1 3 28 插入式振動器 ZX35 0.8 2 1.6 29 插入式振動器 ZX25 0.8 2 1.6 30 交流電焊機 BX3-120XX

6、9 1 9 31 白熾燈 0.01 1 0.01 32 碘鎢燈 0.5 1 0.5 33 塔式起重機 50 1 50 34 灰漿攪拌機 UJ325 3 1 3 35 插入式振動器 ZX35 0.8 2 1.6 36 插入式振動器 ZX25 0.8 2 1.6 37 交流電焊機 BX3-120XX 9 1 9 38 白熾燈 0.01 1 0.01 39 碘鎢燈 0.5 1 0.5 40 熒光燈 YG40 0.04 4 0.16 41 熒光燈 YG40 0.04 16 0.64 42 熒光燈 YG40 0.04 6 0.24 43 熒光燈 YG40 0.04 6 0.24 44 熒光燈 YG40

7、0.04 16 0.64 45 熒光燈 YG40 0.04 16 0.64 46 熒光燈 YG40 0.04 16 0.64 47 熒光燈 YG40 0.04 16 0.64 48 熒光燈 YG40 0.04 4 0.16 -四、設計內容和步驟1、現場勘探及初步設計:(1)本工程所在施工現場范圍內施工前無各種埋地管線。(2)現場采用380V低壓供電，設一配電總箱，內有計量設備，采用TN-S系統供電。(3)根據施工現場用電設備布置情況，總箱進線采用導線空氣明敷/架空線路敷設，干線采用穿硬塑料管敷設，用電器導線采用穿硬塑料管敷設。布置位置及線路走向參見臨時配電系統圖及現場平面圖，采用三級配電，三級

8、防護。(4)按照J(rèn)GJ46-20XX規定制定施工組織設計，接地電阻R4。2、確定用電負荷:(1)、塔式起重機Kx = 0.7 Cos = 0.9 tg = 0.48將Jc =40%統一換算到Jc1 =25%的額定容量Pn = 50kWPe = n(Jc/Jc1)1/2Pn = 1(0.4/0.25)1/250 = 63.25 kWPjs = KxPe =0.763.25 = 44.27kWQjs = Pjs tg=44.270.48 = 21.44 kvar(2)、建筑施工外用電梯Kx = 0.7 Cos = 0.6 tg = 1.33Pjs = 0.711 = 7.7 kWQjs = Pjs

9、 tg=7.71.33 = 10.27 kvar(3)、灰漿攪拌機Kx = 0.5 Cos = 0.55 tg = 1.52Pjs = 0.53 = 1.5 kWQjs = Pjs tg=1.51.52 = 2.28 kvar(4)、木工圓鋸Kx = 0.65 Cos = 0.6 tg = 1.33Pjs = 0.653 = 1.95 kWQjs = Pjs tg=1.951.33 = 2.6 kvar(5)、插入式振動器Kx = 0.3 Cos = 0.7 tg = 1.02Pjs = 0.32.4 = 0.72 kWQjs = Pjs tg=0.721.02 = 0.73 kvar(6)、

10、插入式振動器Kx = 0.3 Cos = 0.7 tg = 1.02Pjs = 0.31.6 = 0.48 kWQjs = Pjs tg=0.481.02 = 0.49 kvar(7)、交流電焊機Kx = 0.5 Cos = 0.4 tg = 2.29將Jc =50%統一換算到Jc1 =100%的額定容量Pn = Sn Cos = 90.4=3.6kWPe = n(Jc/Jc1)1/2Pn = 1(0.5/1)1/23.6 = 2.55 kWPjs = KxPe =0.52.55 = 1.27kWQjs = Pjs tg=1.272.29 = 2.92 kvar(8)、白熾燈Kx = 1 Co

11、s = 1 tg = 0Pjs = 10.011 = 0.01 kWQjs = Pjs tg=0.010 = 0 kvar(9)、碘鎢燈Kx = 0.6 Cos = 0.6 tg = 1.33Pjs = 0.60.51 = 0.3 kWQjs = Pjs tg=0.31.33 = 0.4 kvar(10)、建筑施工外用電梯Kx = 0.7 Cos = 0.6 tg = 1.33Pjs = 0.711 = 7.7 kWQjs = Pjs tg=7.71.33 = 10.27 kvar(11)、灰漿攪拌機Kx = 0.5 Cos = 0.55 tg = 1.52Pjs = 0.53 = 1.5 k

12、WQjs = Pjs tg=1.51.52 = 2.28 kvar(12)、鋼筋調直機Kx = 0.65 Cos = 0.7 tg = 1.02Pjs = 0.654 = 2.6 kWQjs = Pjs tg=2.61.02 = 2.65 kvar(13)、鋼筋彎曲機Kx = 0.65 Cos = 0.7 tg = 1.02Pjs = 0.653 = 1.95 kWQjs = Pjs tg=1.951.02 = 1.99 kvar(14)、鋼筋切斷機Kx = 0.65 Cos = 0.7 tg = 1.02Pjs = 0.653 = 1.95 kWQjs = Pjs tg=1.951.02 =

13、 1.99 kvar(15)、木工圓鋸Kx = 0.65 Cos = 0.6 tg = 1.33Pjs = 0.653 = 1.95 kWQjs = Pjs tg=1.951.33 = 2.6 kvar(16)、插入式振動器Kx = 0.3 Cos = 0.7 tg = 1.02Pjs = 0.32.4 = 0.72 kWQjs = Pjs tg=0.721.02 = 0.73 kvar(17)、插入式振動器Kx = 0.3 Cos = 0.7 tg = 1.02Pjs = 0.31.6 = 0.48 kWQjs = Pjs tg=0.481.02 = 0.49 kvar(18)、交流電焊機K

14、x = 0.5 Cos = 0.4 tg = 2.29將Jc =50%統一換算到Jc1 =100%的額定容量Pn = Sn Cos = 90.4=3.6kWPe = n(Jc/Jc1)1/2Pn = 1(0.5/1)1/23.6 = 2.55 kWPjs = KxPe =0.52.55 = 1.27kWQjs = Pjs tg=1.272.29 = 2.92 kvar(19)、白熾燈Kx = 1 Cos = 1 tg = 0Pjs = 10.011 = 0.01 kWQjs = Pjs tg=0.010 = 0 kvar(20XX碘鎢燈Kx = 0.6 Cos = 0.6 tg = 1.33P

15、js = 0.60.51 = 0.3 kWQjs = Pjs tg=0.31.33 = 0.4 kvar(21)、塔式起重機Kx = 0.7 Cos = 0.9 tg = 0.48將Jc =40%統一換算到Jc1 =25%的額定容量Pn = 50kWPe = n(Jc/Jc1)1/2Pn = 1(0.4/0.25)1/250 = 63.25 kWPjs = KxPe =0.763.25 = 44.27kWQjs = Pjs tg=44.270.48 = 21.44 kvar(22)、建筑施工外用電梯Kx = 0.7 Cos = 0.6 tg = 1.33Pjs = 0.711 = 7.7 kW

16、Qjs = Pjs tg=7.71.33 = 10.27 kvar(23)、灰漿攪拌機Kx = 0.5 Cos = 0.55 tg = 1.52Pjs = 0.53 = 1.5 kWQjs = Pjs tg=1.51.52 = 2.28 kvar(24)、鋼筋調直機Kx = 0.65 Cos = 0.7 tg = 1.02Pjs = 0.654 = 2.6 kWQjs = Pjs tg=2.61.02 = 2.65 kvar(25)、鋼筋彎曲機Kx = 0.65 Cos = 0.7 tg = 1.02Pjs = 0.653 = 1.95 kWQjs = Pjs tg=1.951.02 = 1.

17、99 kvar(26)、鋼筋切斷機Kx = 0.65 Cos = 0.7 tg = 1.02Pjs = 0.653 = 1.95 kWQjs = Pjs tg=1.951.02 = 1.99 kvar(27)、木工圓鋸Kx = 0.65 Cos = 0.6 tg = 1.33Pjs = 0.653 = 1.95 kWQjs = Pjs tg=1.951.33 = 2.6 kvar(28)、插入式振動器Kx = 0.3 Cos = 0.7 tg = 1.02Pjs = 0.31.6 = 0.48 kWQjs = Pjs tg=0.481.02 = 0.49 kvar(29)、插入式振動器Kx =

18、 0.3 Cos = 0.7 tg = 1.02Pjs = 0.31.6 = 0.48 kWQjs = Pjs tg=0.481.02 = 0.49 kvar(30)、交流電焊機Kx = 0.5 Cos = 0.4 tg = 2.29將Jc =50%統一換算到Jc1 =100%的額定容量Pn = Sn Cos = 90.4=3.6kWPe = n(Jc/Jc1)1/2Pn = 1(0.5/1)1/23.6 = 2.55 kWPjs = KxPe =0.52.55 = 1.27kWQjs = Pjs tg=1.272.29 = 2.92 kvar(31)、白熾燈Kx = 1 Cos = 1 tg

19、 = 0Pjs = 10.011 = 0.01 kWQjs = Pjs tg=0.010 = 0 kvar(32)、碘鎢燈Kx = 0.6 Cos = 0.6 tg = 1.33Pjs = 0.60.51 = 0.3 kWQjs = Pjs tg=0.31.33 = 0.4 kvar(33)、塔式起重機Kx = 0.7 Cos = 0.9 tg = 0.48將Jc =40%統一換算到Jc1 =25%的額定容量Pn = 50kWPe = n(Jc/Jc1)1/2Pn = 1(0.4/0.25)1/250 = 63.25 kWPjs = KxPe =0.763.25 = 44.27kWQjs =

20、Pjs tg=44.270.48 = 21.44 kvar(34)、灰漿攪拌機Kx = 0.5 Cos = 0.55 tg = 1.52Pjs = 0.53 = 1.5 kWQjs = Pjs tg=1.51.52 = 2.28 kvar(35)、插入式振動器Kx = 0.3 Cos = 0.7 tg = 1.02Pjs = 0.31.6 = 0.48 kWQjs = Pjs tg=0.481.02 = 0.49 kvar(36)、插入式振動器Kx = 0.3 Cos = 0.7 tg = 1.02Pjs = 0.31.6 = 0.48 kWQjs = Pjs tg=0.481.02 = 0.

21、49 kvar(37)、交流電焊機Kx = 0.5 Cos = 0.4 tg = 2.29將Jc =50%統一換算到Jc1 =100%的額定容量Pn = Sn Cos = 90.4=3.6kWPe = n(Jc/Jc1)1/2Pn = 1(0.5/1)1/23.6 = 2.55 kWPjs = KxPe =0.52.55 = 1.27kWQjs = Pjs tg=1.272.29 = 2.92 kvar(38)、白熾燈Kx = 1 Cos = 1 tg = 0Pjs = 10.011 = 0.01 kWQjs = Pjs tg=0.010 = 0 kvar(39)、碘鎢燈Kx = 0.6 Co

22、s = 0.6 tg = 1.33Pjs = 0.60.51 = 0.3 kWQjs = Pjs tg=0.31.33 = 0.4 kvar(40)、熒光燈Kx = 0.75 Cos = 0.85 tg = 0.62Pjs = 0.750.161.2 = 0.144 kWQjs = Pjs tg=0.140.62 = 0.09 kvar(41)、熒光燈Kx = 0.75 Cos = 0.85 tg = 0.62Pjs = 0.750.641.2 = 0.576 kWQjs = Pjs tg=0.580.62 = 0.36 kvar(42)、熒光燈Kx = 0.75 Cos = 0.85 tg

23、= 0.62Pjs = 0.750.241.2 = 0.216 kWQjs = Pjs tg=0.220.62 = 0.13 kvar(43)、熒光燈Kx = 0.75 Cos = 0.85 tg = 0.62Pjs = 0.750.241.2 = 0.216 kWQjs = Pjs tg=0.220.62 = 0.13 kvar(44)、熒光燈Kx = 0.75 Cos = 0.85 tg = 0.62Pjs = 0.750.641.2 = 0.576 kWQjs = Pjs tg=0.580.62 = 0.36 kvar(45)、熒光燈Kx = 0.75 Cos = 0.85 tg = 0

24、.62Pjs = 0.750.641.2 = 0.576 kWQjs = Pjs tg=0.580.62 = 0.36 kvar(46)、熒光燈Kx = 0.75 Cos = 0.85 tg = 0.62Pjs = 0.750.641.2 = 0.576 kWQjs = Pjs tg=0.580.62 = 0.36 kvar(47)、熒光燈Kx = 0.75 Cos = 0.85 tg = 0.62Pjs = 0.750.641.2 = 0.576 kWQjs = Pjs tg=0.580.62 = 0.36 kvar(48)、熒光燈Kx = 0.75 Cos = 0.85 tg = 0.62

25、Pjs = 0.750.161.2 = 0.144 kWQjs = Pjs tg=0.140.62 = 0.09 kvar(49)總的計算負荷計算，總箱同期系數取 Kx = 0.9總的有功功率Pjs = KxPjs = 0.9(44.27+7.7+1.5+1.95+0.72+0.48+1.27+0.01+0.3+7.7+1.5+2.6+1.95+1.95+1.95+0.72+0.48+1.27+0.01+0.3+44.27+7.7+1.5+2.6+1.95+1.95+1.95+0.48+0.48+1.27+0.01+0.3+44.27+1.5+0.48+0.48+1.27+0.01+0.3+0

26、.14+0.58+0.22+0.22+0.58+0.58+0.58+0.58+0.14) = 175.516 kW總的無功功率Qjs = KxQjs =0.9(21.44+10.27+2.28+2.6+0.73+0.49+2.92+0+0.4+10.27+2.28+2.65+1.99+1.99+2.6+0.73+0.49+2.92+0+0.4+21.44+10.27+2.28+2.65+1.99+1.99+2.6+0.49+0.49+2.92+0+0.4+21.44+2.28+0.49+0.49+2.92+0+0.4+0.09+0.36+0.13+0.13+0.36+0.36+0.36+0.3

27、6+0.09) = 130.685 kvar總的視在功率Sjs = ( Pjs2+Qjs2 )1/2 = (175.5162+130.6852)1/2 = 218.826 kVA總的計算電流計算Ijs = Sjs/(1.732Ue) = 218.826/(1.7320.38) = 332.481 A3、1號二級配電箱線路上導線截面及分配箱、開關箱內電氣設備選擇:在選擇前應對照平面圖和系統圖先由用電設備至開關箱計算，再由開關箱至分配箱計算，選擇導線及開關設備。分配箱至開關箱，開關箱至用電設備的導線敷設采用銅橡皮絕緣導線穿硬塑料管敷設。(1)、塔式起重機開關箱至塔式起重機導線截面及開關箱內電氣設備

28、選擇(開關箱以下用電器啟動后需要系數取1):3、計算電流Kx = 1 Cos = 0.9 tg = 0.48Ijs = Kx Pe /(1.732Ue Cos) = 163.25/(1.7320.380.9) = 106.77Aii)選擇導線選擇YJV-335+216 ，穿硬塑料管時其安全載流量為0A。iii)選擇電氣設備選擇開關箱內隔離開關為DZ10-250/3 ，其脫扣器整定電流值為Ir = 20XX，漏電保護器為 DZ10L-250/3。(2)、建筑施工外用電梯開關箱至建筑施工外用電梯導線截面及開關箱內電氣設備選擇(開關箱以下用電器啟動后需要系數取1):i)計算電流Kx = 1 Cos

29、= 0.6 tg = 1.33Ijs = Kx Pe /(1.732Ue Cos) = 111/(1.7320.380.6) = 27.86Aii)選擇導線選擇YJV-435 ，穿硬塑料管時其安全載流量為0A。4、選擇電氣設備選擇開關箱內隔離開關為DZ10-250/3 ，其脫扣器整定電流值為Ir = 20XX，漏電保護器為 DZ10L-250/3。(3)、灰漿攪拌機開關箱至灰漿攪拌機導線截面及開關箱內電氣設備選擇(開關箱以下用電器啟動后需要系數取1):i)計算電流Kx = 1 Cos = 0.55 tg = 1.52Ijs = Kx Pe /(1.732Ue Cos) = 13/(1.7320

30、.380.55) = 8.29Aii)選擇導線選擇YJV-52.5 ，穿硬塑料管時其安全載流量為0A。iii)選擇電氣設備選擇開關箱內隔離開關為Hk1-15/3，漏電保護器為 DZ10L-250/3。(4)、木工圓鋸開關箱至木工圓鋸導線截面及開關箱內電氣設備選擇(開關箱以下用電器啟動后需要系數取1):i)計算電流Kx = 1 Cos = 0.6 tg = 1.33Ijs = Kx Pe /(1.732Ue Cos) = 13/(1.7320.380.6) = 7.6Aii)選擇導線選擇YJV-52.5 ，穿硬塑料管時其安全載流量為0A。iii)選擇電氣設備選擇開關箱內隔離開關為Hk1-15/3

31、，漏電保護器為 DZ10L-250/3。(5)、插入式振動器開關箱至插入式振動器導線截面及開關箱內電氣設備選擇(開關箱以下用電器啟動后需要系數取1):i)計算電流Kx = 1 Cos = 0.7 tg = 1.02Ijs = Kx Pe /(1.732Ue Cos) = 10.8/(1.7320.380.7) = 1.74Aii)選擇導線選擇YJV-52.5 ，穿硬塑料管時其安全載流量為0A。iii)選擇電氣設備由于開關控制3臺用電器，開關的電流為Ir=1.743.00(臺數)= 5.21 A。選擇開關箱內隔離開關為DZ5-50/3 ，其脫扣器整定電流值為Ir = 40A，漏電保護器為 DZ1

32、0L-250/3。(6)、插入式振動器開關箱至插入式振動器導線截面及開關箱內電氣設備選擇(開關箱以下用電器啟動后需要系數取1):i)計算電流Kx = 1 Cos = 0.7 tg = 1.02Ijs = Kx Pe /(1.732Ue Cos) = 10.8/(1.7320.380.7) = 1.74Aii)選擇導線選擇YJV-52.5 ，穿硬塑料管時其安全載流量為0A。iii)選擇電氣設備由于開關控制2臺用電器，開關的電流為Ir=1.742.00(臺數)= 3.47 A。選擇開關箱內隔離開關為DZ5-50/3 ，其脫扣器整定電流值為Ir = 40A，漏電保護器為 DZ10L-250/3。(7

33、)、交流電焊機開關箱至交流電焊機導線截面及開關箱內電氣設備選擇(開關箱以下用電器啟動后需要系數取1):i)計算電流Kx = 1 Cos = 0.4 tg = 2.29Ijs = Kx Pe /(Ue Cos) = 12.55/(0.380.4) = 16.75Aii)選擇導線選擇YJV-46+12.5 ，穿硬塑料管時其安全載流量為0A。iii)選擇電氣設備選擇開關箱內隔離開關為DZ10-100/3 ，其脫扣器整定電流值為Ir = 80A，漏電保護器為 DZ10L-250/3。(8)、白熾燈開關箱至白熾燈導線截面及開關箱內電氣設備選擇(開關箱以下用電器啟動后需要系數取1):i)計算電流Kx =

34、1 Cos = 1 tg = 0Ijs = Kx Pe /(Ue Cos) = 10.01/(0.221) = 0.05Aii)選擇導線選擇YJV-52.5 ，穿硬塑料管時其安全載流量為0A。iii)選擇電氣設備選擇開關箱內隔離開關為DZ15-63/3 ，其脫扣器整定電流值為Ir = 49A，漏電保護器為 DZ10L-250/3。(9)、碘鎢燈開關箱至碘鎢燈導線截面及開關箱內電氣設備選擇(開關箱以下用電器啟動后需要系數取1):i)計算電流Kx = 1 Cos = 0.6 tg = 1.33Ijs = Kx Pe /(Ue Cos) = 10.5/(0.220.6) = 3.79Aii)選擇導線

35、選擇YJV-52.5 ，穿硬塑料管時其安全載流量為0A。iii)選擇電氣設備選擇開關箱內隔離開關為DZ15-63/3 ，其脫扣器整定電流值為Ir = 49A，漏電保護器為 DZ10L-250/3。(10)、1號塔吊三級動力箱至第1組電機(塔式起重機)的開關箱的導線截面及分配箱內開關的選擇i) 計算電流塔式起重機Kx = 0.7 Cos= 0.9 tg= 0.48Ijs = Kx Pe 臺數/(1.732Ue Cos) = 0.763.251/(1.7320.380.9) = 74.74AIjs(1組電機 )= 74.74A該組中最大的開關箱電流Ijs=106.77A兩者中取大值Ijs=106.

36、77Aii)選擇導線選擇YJV-435+116 ，穿硬塑料管時其安全載流量為0A。iii)選擇電氣設備選擇分配箱內開關為DZ10-250/3 ，其脫扣器整定電流值為Ir = 20XX，漏電保護器為 DZ10L-250/3。(11)、1人貨梯三級動力箱至第1組電機(建筑施工外用電梯)的開關箱的導線截面及分配箱內開關的選擇i) 計算電流建筑施工外用電梯Kx = 0.7 Cos= 0.6 tg= 1.33Ijs= Kx Pe 臺數/(1.732Ue Cos) = 0.7111/(1.7320.380.6) = 19.5AIjs(1組電機 )= 19.5A該組中最大的開關箱電流Ijs=27.86A兩者

37、中取大值Ijs=27.86Aii)選擇導線選擇YJV-435+116 ，穿硬塑料管時其安全載流量為0A。iii)選擇電氣設備選擇分配箱內開關為DZ10-250/3 ，其脫扣器整定電流值為Ir = 20XX，漏電保護器為 DZ10L-250/3。(12)、2砂漿機三級動力箱至第1組電機(灰漿攪拌機)的開關箱的導線截面及分配箱內開關的選擇i) 計算電流灰漿攪拌機Kx = 0.5 Cos= 0.55 tg= 1.52Ijs= Kx Pe 臺數/(1.732Ue Cos) = 0.531/(1.7320.380.55) = 4.14AIjs(1組電機 )= 4.14A該組中最大的開關箱電流Ijs=8.

38、29A兩者中取大值Ijs=8.29Aii)選擇導線選擇YJV-52.5 ，穿硬塑料管時其安全載流量為0A。iii)選擇電氣設備選擇分配箱內開關為DZ15-63/3 ，其脫扣器整定電流值為Ir = 49A，漏電保護器為 DZ10L-250/3。(13)、臺式園鋸三級動力箱至第1組電機(木工圓鋸)的開關箱的導線截面及分配箱內開關的選擇i) 計算電流木工圓鋸Kx = 0.65 Cos= 0.6 tg= 1.33Ijs= Kx Pe 臺數/(1.732Ue Cos) = 0.6531/(1.7320.380.6) = 4.94AIjs(1組電機 )= 4.94A該組中最大的開關箱電流Ijs=7.6A兩

39、者中取大值Ijs=7.60Aii)選擇導線選擇YJV-52.5 ，穿硬塑料管時其安全載流量為0A。iii)選擇電氣設備選擇分配箱內開關為DZ5-50/3 ，其脫扣器整定電流值為Ir = 40A，漏電保護器為 DZ15L-100/30。(14)、50mm砼振動器三級動力箱至第1組電機(插入式振動器)的開關箱的導線截面及分配箱內開關的選擇i) 計算電流插入式振動器Kx = 0.3 Cos= 0.7 tg= 1.02Ijs= Kx Pe 臺數/(1.732Ue Cos) = 0.30.83/(1.7320.380.7) = 1.56AIjs(1組電機 )= 1.56A該組中最大的開關箱電流Ijs=5

40、.21A兩者中取大值Ijs=5.21Aii)選擇導線選擇YJV-52.5 ，穿硬塑料管時其安全載流量為0A。iii)選擇電氣設備選擇分配箱內開關為DZ5-50/3 ，其脫扣器整定電流值為Ir = 40A，漏電保護器為 DZ10L-250/3。(15)、30mm砼振動器三級動力箱至第1組電機(插入式振動器)的開關箱的導線截面及分配箱內開關的選擇i) 計算電流插入式振動器Kx = 0.3 Cos= 0.7 tg= 1.02Ijs= Kx Pe 臺數/(1.732Ue Cos) = 0.30.82/(1.7320.380.7) = 1.04AIjs(1組電機 )= 1.04A該組中最大的開關箱電流I

41、js=3.47A兩者中取大值Ijs=3.47Aii)選擇導線選擇YJV-52.5 ，穿硬塑料管時其安全載流量為0A。iii)選擇電氣設備選擇分配箱內開關為DZ5-50/3 ，其脫扣器整定電流值為Ir = 40A，漏電保護器為 DZ10L-250/3。(16)、交流電焊機三級動力箱至第1組電機(交流電焊機)的開關箱的導線截面及分配箱內開關的選擇i) 計算電流交流電焊機Kx = 0.5 Cos= 0.4 tg= 2.29Ijs = Kx Pe 臺數/(Ue Cos) = 0.52.551/(0.380.4) = 8.37AIjs(1組電機 )= 8.37A該組中最大的開關箱電流Ijs=16.75A

42、兩者中取大值Ijs=16.75Aii)選擇導線選擇YJV-46+12.5 ，穿硬塑料管時其安全載流量為0A。iii)選擇電氣設備選擇分配箱內開關為DZ10-100/3 ，其脫扣器整定電流值為Ir = 80A，漏電保護器為 DZ10L-250/3。(17)、照明分箱至第1組照明燈具(白熾燈、碘鎢燈)的開關箱的導線截面及分配箱內開關的選擇i) 計算電流白熾燈Kx = 1 Cos= 1 tg= 0Ijs = Kx Pe 臺數/(Ue Cos) = 10.011/(0.221) = 0.02A碘鎢燈Kx = 0.6 Cos= 0.6 tg= 1.33Ijs = Kx Pe 臺數/(Ue Cos) =

43、0.60.51/(0.220.6) = 0.76AIjs(1組燈具 )= 0.77A該組中最大的開關箱電流Ijs=3.79A由于該組下有多個開關箱，所以最大電流需要乘以1.1的系數兩者中取大值Ijs=3.791.1=4.17Aii)選擇導線選擇YJV-52.5 ，穿硬塑料管時其安全載流量為0A。iii)選擇電氣設備選擇分配箱內開關為DZ10-100/3 ，其脫扣器整定電流值為Ir = 80A，漏電保護器為 DZ10L-250/3。4、1號塔吊三級動力箱進線及進線開關的選擇i)計算電流Kx = 0.7，Cos = 0.9Ijs = KxPe /(1.732Ue Cos) = 0.750/(1.7

44、320.380.9) = 59.09A該分箱下最大組線電流Ijs=106.77A兩者中取大值Ijs=106.77Aii)選擇導線選擇YJV-4150+190 ，穿硬塑料管時其安全載流量為0A。iii)選擇電氣設備選擇分配箱內開關為DZ10-250/3 ，其脫扣器整定電流值為Ir = 20XX，漏電保護器為 DZ10L-250/3。5、1人貨梯三級動力箱進線及進線開關的選擇i)計算電流Kx = 0.7，Cos = 0.9Ijs = KxPe /(1.732Ue Cos) = 0.711/(1.7320.380.9) = 13A該分箱下最大組線電流Ijs=27.86A兩者中取大值Ijs=27.86

45、Aii)選擇導線選擇YJV-435+116 ，穿硬塑料管時其安全載流量為0A。iii)選擇電氣設備選擇分配箱內開關為DZ10-250/3 ，其脫扣器整定電流值為Ir = 20XX，漏電保護器為 DZ10L-250/3。6、2砂漿機三級動力箱進線及進線開關的選擇i)計算電流Kx = 0.7，Cos = 0.9Ijs = KxPe /(1.732Ue Cos) = 0.73/(1.7320.380.9) = 3.55A該分箱下最大組線電流Ijs=8.29A兩者中取大值Ijs=8.29Aii)選擇導線選擇YJV-435+116 ，穿硬塑料管時其安全載流量為0A。iii)選擇電氣設備選擇分配箱內開關為

46、DZ15-63/3 ，其脫扣器整定電流值為Ir = 49A，漏電保護器為 DZ10L-250/3。7、臺式園鋸三級動力箱進線及進線開關的選擇i)計算電流Kx = 0.7，Cos = 0.9Ijs = KxPe /(1.732Ue Cos) = 0.73/(1.7320.380.9) = 3.55A該分箱下最大組線電流Ijs=7.60A兩者中取大值Ijs=7.60Aii)選擇導線選擇YJV-435+116 ，穿硬塑料管時其安全載流量為0A。iii)選擇電氣設備選擇分配箱內開關為DZ15-63/3 ，其脫扣器整定電流值為Ir = 49A，漏電保護器為 DZ10L-250/3。(22)50mm砼振動器三級動力箱進線及進線開關的選擇i)計算電流Kx = 0.7，Cos = 0.9Ijs = KxPe /(1.732Ue Cos) = 0.70.8/(1.7320.380.9) = 0.95A該分箱下最大組線電流Ijs=5.21A兩者中取大值Ijs=5.21Aii)選擇導線選擇YJV-435+116 ，穿硬塑料管時其安全載流量為0A。iii)選擇電氣設備選擇分配箱內開關為DZ5-50/3 ，其脫扣器整定電流值為Ir = 40A，漏電保護器為 DZ10L-250