版權說明:本文檔由用戶提供并上傳,收益歸屬內容提供方,若內容存在侵權,請進行舉報或認領
文檔簡介
1、修訂記錄Revision History編制人Author日期Date修訂內容Change Description版本號Rev批準Approvals職位Position姓名Name簽名Signature日期Date1.目的:Purpose:The purpose of this document is to detail the specific steps necessary for a lab technician to perform the iDEN Parametric Test.本文檔詳細描述了實驗室技術員如何完成iDEN系統參數測試所需要的詳細測試步驟2 范圍:Scope:The
2、 scope of this document is to instruct the lab technician on how to perform iDEN parametric testing for products run on the Motorola ALT flow 00R89144W01 using manual method instead of ATE.本文檔規范了本實驗室技術員遵照摩托羅拉生命加速測試流程(00R89144W01 )標準,通過手動方法進行iDEN系統參數測試,從而取代自動化測試機測試。3 職責:Responsibility:It is the respo
3、nsibility of lab technician to ensure proper usage of the equipment during testing. It is the responsibility of lab technician to ensure that the proper test setting is used prior to use of the equipment.實驗室技術人員負責在實驗過程中,確保儀器設備工作在正常狀態并確保在儀器設備使用前將儀器設備進行正確的設置。4 定義:Definition:TermDefinitionATEAutomated
4、Test Equipment自動測試儀ALTAccelerated Life Test生命加速試驗iDENIntegrated Digital Enhanced Network集成數字增強型網絡5 程序:Procedure:5.1主要設備:Agilent Vector Signal Analyzer N9010AAgilent RF Power Meter E4418BAgilent Vector Signal Generator E4438CAgilent Power Supply 66319BWillTek RF Shield Box and AntennaLaboratory PC安捷倫
5、無線電信號分析儀N9010A安捷倫射頻功率計 E4418B安捷倫無線電信號發生器E4438C安捷倫直流電源 66319BWillTek射頻屏蔽盒與天線工業控制電腦5.2 Test setupRefer to diagram to set up the iDEN parametric test equipment. The GPIB cable is meant for automation. The GPIB cable to the E4438C is needed for one time loading of iDEN and Mototalk waveforms to the equi
6、pment. All equipment should be turned on one hour before any test is done. This is to allow the equipment to stabilize sufficiently enough to make the correct measurement,以下是iDEN參數測試的連接圖。GPIB電纜是用來進行自動化測試。第一次連接E4438C時需要用到GPIB電纜進行波形下載。所有儀器在測試前至少開機一小時以保證各項參數處于正常狀態。IQ MHz mE4J3SCAgilent NS010 A"電 t
7、ier 5 啥 nM AnalyzerAglltrrt E441JB RF power metrunderRifilo PrcibBattcrvNAfiDAWestSDDJIDOOMMCirculatorShield BoxAgilent 6631 SBPower SupplyMBAgilent E443KV電ctor馴 G-eneratoirWindows PCGPIBGPIBT Serialto USB Interface to Radio5.3 安裝iDEN和Mototalk波形到E4438C 儀器中。The following software and files are needed
8、.以下是安裝波形所必備的軟件a. IntuiLink.exeb. Microsoft officec. i_16QAM.bin and q_16QAM.bin files for iDEN waveformsd. MTS_I.txt and MTS2_Q.txt files for Mototalk waveforms4.3.1 Install the Intuilink.exe software.安裝Intuilink軟件4.3.2 Connect a GPIB card to E4438C with a GPIB cable.將E4438C通過GPIB與電腦進行連接4.3.3 Open M
9、icrosoft Excel打開Excel表格4.3.4 Goto View > Toolbars > PSG/ESG signal generator . The following toolbar will appear.點擊視圖菜單下的工具欄中的PSG/ESG signal generator 工具欄.P5G/ESG 號Gien史 r 己t:口r- X之后會出現類似下面的工具欄卜鵬阿EtP蚓E5G 鋁 :等 O4.3.5 Click on Agilent PSG/ESG . The following dialogue box will appear.點擊 Agilent P
10、SG/ESG 按鈕Agilent PSG/ESG Signal Generator二£:3; Agilent TechnologiesIntuiLinkfor PSG/ESG SeriesSignal GeneratorsSupported Models: 人加曰m onW2b IntuiLink on th白 Web .E 5Gg the Web PSG onthcW-bE4435BE4438B正4437BE4438cE4438CCopyright © 1999-2003, Agieri Technobgies, Version 4.2.0.25Component Inf
11、oOK4.3.6 Choose E4438C and press OK.選才i E4438C后點擊OK4.3.7 Press the Connect to PSG/ESG Signal Generator button. 選擇連接到 Signal Generator。PG/ESG Signal Generator x讀阿ent P5G/E5G 函 金西 C口nn一匚t tdSiign-I 6它口巳-匕口,|4.3.8 Choose the correct address for E4438C and press Identify Instrument . Then press Connect
12、and the status will show Connected ” . Next press Close button.選才E E4438C儀器正確地址并點擊Identify Instrument識別儀器按鈕,然后點擊 Connect連接按 鈕,并且右側的狀態由原先的disconnect轉變?yōu)镃onnected,點擊Close關閉按鈕5.3.9 To load waveform into E4438c. Press theDownload ARB Waveform Databutton.P5G/ESG 號Cii&nEr dtnr x點擊Download ARB waveform按
13、鈕進行下載波形| 漆-如lent PSQ/ESG g 啕固01Dovwnhfld Arb Waveform Data5.3.10 In the dialogue, select File Folders, etc and browse for the waveforms.進入到對話中1后點擊Browse按鈕選擇波形File names: i_16QAM.bin and q_16QAM.bin選擇i_16QAM.bin文件Type: 14-Bit Internal Values類型:選擇14Bit Internal Values14 位內部值File Type: Little Endian文件類
14、型:選擇 Little EndianE4438C Generator ParametersSample Rate: 400 kHz使用16QAM波形時將E4438C信號發生器的采樣率設置為400kHzFile names: MTS2_!.txt and MTS2_Q.txt文件名為MTS2 i.txtType: 14-Bit Internal Values File Type: Little Endian E4438c Generator ParametersSample Rate: 192 kHz使用MTS2文件時將E4438C的采樣率設置為192kHzAfter choosing the
15、correct waveform, press Validate Files then Start Download. After completed downloading the waveform into E4438C, the waveform is then in the Volatile memory. In the next step, store the waveform into the Non-volatile memory.選擇正確的波形后,點擊Validate Files按鈕進行驗證,成功后點擊Start Download 按鈕進行下載波形。下載完畢后將波形永久儲存到E
16、4438C儀器中。5.4 Store the iDEN and Mototalk waveforms into Non-volatile memory.將波形儲存到儀器中并且保證儀器每次重新啟動后都可以選擇此波形。Press Mode > Dual ARB > Waveform Segments . Then Press Store All to NVMFM Memory soft key.點擊Mode模式按鈕,選擇 Dual ARB按鈕,點擊 Waveform Selected按鈕進行波形選擇,再點擊 Waveform Segments按鈕進行波形分類,點擊Store按鈕存儲,選
17、擇 Store all to NVMFM Memory 按鈕存儲所有波形到存儲器中Should the E4438C be powered down and all waveforms in the Volatile memory are lost. Perform the load waveforms from Non-volatile memory to Volatile memory by following the following steps.當E4438C關機后所有存儲在 Volatile存儲器中的波形都會消失,點擊Load按鈕將之前存儲的波形調到Volatile存儲器中。.Th
18、en, press Load All From NVWFMPress Mode > Dual ARB > Waveform SegmentsMemory soft key.5.5 Zero and Calibrate the Power Meter E4418B將 E4418B 功率計歸零和校準Before starting the test, zero and calibrate the power meter by following the steps below: 在開始測試前,需要按照以下的步驟將功率計進行歸零和校準。Press the <Preset> an
19、d <Confirm> to preset the power meter key 點擊 Preset 按鈕并點擊Confirm 確認按鈕將功率計初始化Remove the power sensor from connection, and press the <Zero/Cal> button. 將 Power 傳感器與功率計斷開并點擊歸零校準按鈕。Press the <Zero> button to zero the power meter.點擊 Zero 歸零按鈕將功率計讀數歸零Connect the power sensor to its refer
20、ence output port. Press the <Power Ref> to On. Press the <Cal> button to calibrate the power meter.將功率傳感器連接到功率計的輸出口,并點擊Power Ref 按鈕進行基準功率輸出,點擊Cal 校準按鈕進行校準。Press the <Power Ref> to Off.點擊 Power Ref 按鈕關閉基準功率輸出The Power meter is now ready for use. 現在功率計就可以進行使用了。5.6 Path Loss Calibrati
21、onThe path loss calibration consists of three steps.路徑衰減的校準包含以下三部分。5.6.1 Measure the Signal Generator Output 測量信號發生器的輸出Connect the power meter sensor directly to the signal generator E4438C. Press the <ModOn/Off> button to turn off the modulation. Press < RF On/Off> to turn on the RF. Se
22、t the frequency to the test frequency (Refer to product 12M for the test frequencies). Set the amplitude to -20 dBm. On the power meter E4418B, set the measure frequency to the same test frequency. Record the reading on the power meter. Repeat the measurement for the rest of the test frequencies. Th
23、e measured data are the reference for the path loss calibration.將功率計直接連接到 E4438C 上,點擊 MOD 按鈕關閉調制功能,點擊RF 按鈕打開 RF 輸出,設置輸出頻率按照產品 12M 上定義的頻率進行設置,將Amplitude 振幅設置為 -20dBm ,將功率計的頻率設置為要測試的頻率,記錄此時功率計的讀數,重復此校準步驟在別的頻率下,這些數據可以作為路徑衰減的參考。1.1.1 Tx Path Loss Calibration 發射路徑衰減校準Refer to diagram below, remove the co
24、nnector from the shield box and connect it directly to E4438C.E4438C 上。以下是發射路徑校準的連接圖,將屏蔽箱的連接器拿掉并將它直接連接到10 MHz Refer eibce h4>mE4433CAgilent hl 010AV ect or SignaP Analyze rThe modulation of the signal generator E4438c should still remain as off. Press <RF On/Off>to turn on the RF. Set the f
25、requency to the Tx test frequency. Set the amplitude to -20 dBm. On the power meter E4418B, set the measure frequency to the same test frequency. Record the reading on the power meter. Repeat the measurement for the rest of the test frequencies. Compare the measured data to the reference data measur
26、ed in 6.5.1. The Tx path loss equals to the difference between the measured data and the measured reference data in 6.5.1. The Tx path loss will be used in the Tx power measurement.E4438C上的調制功能始終保持關閉狀態,點擊RF按鈕開啟射頻輸出,將頻率設置為手機的發射頻率,將振幅設置為-20dBm ,同樣的將功率計的頻率設置為手機發射頻率,記錄功率計的讀數,重復 此校準在其他頻率下。比較此時的衰減值與之前6.5.
27、1的結果,這時發射路徑的衰減值就等于這次測量到的值減去6.5.1測量結果,這個衰減值在TX功率測量中要用到。1.1.2 Rx Path Loss Calibration 接收路徑衰減Refer to diagram below, remove the connector from the shield box and connect it directly to power meter sensor.以下是接收路徑衰減的連接圖,將屏蔽箱的連接頭直接連接到功率計上。R 削 llQPrQMGPIBGPIBNAfiOAWest 9???.J 皿丸4 HM Circulator10 MHz Rdeve
28、qice frem E443ICAgile nt NdlOA Vector Sign al Analyzfl rAgilent 6631gB Power SiiijpllyIBnltc-ry fliirilinafrAgiltnl! E4418BRF power m«8 erA gient E443:EtCVector 5ignilGen-eratorA.fjknt77SD 20d& dir e ctionaJ courier£h leldBoxSeriaflto USB Interface to RadioThe modulation of the signal
29、generator E4438c should still remain as off. Press <RF On/Off>to turn on the RF. Set the frequency to the Rx test frequency. Set the amplitude to -20 dBm. On the power meter E4418B, set the measure frequency to the same test frequency. Record the reading on the power meter. Repeat the measurem
30、ent for the rest of the test frequencies. Compare the measured data to the reference data measured in 5.3.1. The Rx path loss equals to the difference between the measured data and the measured reference data in 5.3.1. The Rx path loss will be used in the Rx sensitivity measurement.E4438C上的調制功能始終保持關
31、閉狀態,點擊RF按鈕開啟射頻輸出,將頻率設置為手機的接收頻率,將振幅設置為-20dBm ,同樣的將功率計的頻率設置為手機接收頻率,記錄功率計的讀數,重復 此校準在其他頻率下。比較此時的衰減值與之前5.3.1的結果,這時接收路徑的衰減值就等于這次測量到的值減去5.3.1測量結果,這個衰減值在接收靈敏度測試中要用到。Reconnect the equipment back to the configuration for parametric testings.重新將儀器連接回初始狀態進行參數測試。5.9 Golden Sample Correlation好品對機測試Take the correl
32、ation sample with parametric data measured previously and run through the parametric testing. Compare the results with previous measured data. The transmit power correlation should be within +-0.2 dBm. The receive BER correlatation should be within +-0.5 BER. Adjust the RX and Tx path loss if necess
33、ary. Should the correlation fails, inform the maintenance engineering to troubleshoot the test station.將之前做對機測試的好品數據拿到并將這個手機放入現在的參數測試系統中運行,比較兩次的測 量結果的差異。發射功率的誤差應該在+-0.2dBm之間,接收誤碼率應該在+-0.5倍測量到的誤碼率。如果需要可以調整接收和發送的路徑衰減值。如果對機測試失敗請聯系維護工程師進行測試站檢查。5.10 Set up the HyperTerminalRun the HyperTerminal on the wi
34、ndow PC. Give a name to the connection and click <OK>.打開超級終端并運行AtUdWMIn the next screen, select COM 1 for the Connect using and click OK.選才i COM1端口In the next screen, select 19200 for Bits per second and None for Flow control and click OK.將比特率設置為19200,LWuuffMWiMb 聞總In the next screen, press th
35、e phone disconnect icon to disconnect since the radio under test is not connected to the serial to the USB 丫 cable. To connect, press the phone connect icon.斷開連接后再重新?lián)芴?hào)連接。Press to connectPress to disconnect5.11 Parametric testEnsure the unit has a test SIM card. Place the dummy battery pack on the un
36、it. Set the powersupply 66319B output voltage to 4.1 volt by press voltage and key in 4.1 and press volt. Turn on the radio under test. Manually place the radio under test to Berbug mode if necessary by pressing“#*#654#*#" , and then press Remove the antenna grommet on the phone. Position the r
37、adio under test in the RF enclosure and insert both the RF probe and the serial to USB 丫 cable. Close the RF enclosure.確保待測手機已經安裝好Sim卡,將虛擬電池放入待測手機。將 66319B的電壓設置為4.1V。打開手機,輸入“ #*#654#*# "點擊OK,進入Berbug模式并去掉手機天線的后蓋,將 RF天線連接到此處 并將手機數據線連接到電腦和手機之間。關閉屏蔽箱。Connect the HyperTerminal to the radio under te
38、st by pressing the phone connect icon. Press <Enter> on the PC keyboard a few times to get the Berbug returns from the radio under test to confirm the connection. Send the following Berbug command to the radio under test.連接超級終端LOG ERASE (This is to clear the iDEN reset log.)輸入LOG ERASE命令擦除手機日志
39、文件5.12.1 Standby CurrentMOD IDL (Set the radio under test to idle mode)輸入MOD IDL命令將手機轉入待機模式LED ALL OFF (Turn off all the LEDs)輸入LED ALL OFF命令關閉手機所有LED燈Read the current on the power supply. This shall be the standby current. Record down the reading.讀取此時的66319B的電流,記錄此時的待機電流5.12.2 Dispatch TestOn the E
40、4438C, set the followings:Frequency > 859.45 MHz, RF on, Modulation on, ARB > select 16QAM and play, Amplitude, > equivalent of -111 dBm taking the Rx path loss into consideration. For temperature extreme environment., the amplitude needs to be 3 dB higher.在E4438C上將頻率設置為 859.45MHz,打開RF輸出和調制
41、功能,自定義波形為16QAM。振幅的設置要將-111dBm的固定值和路徑衰減值加在一起。在高低溫測試中,-111dBm固定值需要改變?yōu)? 108dBm 。On the Hyperterminal, send the following Berbug commands打開超級終端輸入以下Berbug 命令SPE INT (This select the internal speaker to output the audio)輸入SPE INT 命令將內部喇叭打開VOL SPE 240 (This sets the speaker volume to 240)輸入VOL SPE 240命令將音量
42、大小調整到240ALE STA 255 (This plays the alert tone selection 255 to the speaker)輸入ALE STA 255命令通過喇叭播放報警音RX FREQ 859.45 (This sets the receive frequency at 859.45 MHz)輸入RX FREQ 859.45 命令將手機接收頻率設定為 859.45MHzMOD RX (This configures the radio under test to receive mode)輸入MOD RX 命令將手機啟動到接收模式GO 16 (Begin disp
43、laying frame measurements according to DISPLAY settings. 16 frame measurements will be taken and results output to screen continuously until ESC key is pressed.)輸入 GO 16 命令開始顯示結果,點擊ESC 鍵可取消輸出結果功能。On the power supply 66319B, read the current. This shall be the dispatch current at 859.45 MHz.在電源上將讀數記錄
44、在 859.45MHz 這個頻率對應的電流值上On the Hyperterminal, send the following Berbug commands to stop the test.輸入以下 Berbug 命令停止測試。ALE STO 255 (This stops playing the alert tone selection 255 to the speaker)輸入 ALE STO 255 命令將報警音關掉SPE OFF (This turns off the speaker selection)輸入SPE OFF 命令關閉喇叭功能MOD IDL (This configu
45、res the radio under test to idle mode)輸入MOD IDL 命令將手機轉入待機模式。Repeat the test for the other frequency (937.49375 MHz) by changing the frequency and amplitude accordingly.重復此測試在 937.49375MHz 這個頻率上并記錄。5.12.3 Rx BER TestOn the E4438C, set the followings:Frequency > 859.45 MHz, RF on, Modulation on, AR
46、B > select 16QAM and play, Amplitude, > equivalent of -111 dBm taking the Rx path loss into consideration. For temperature extreme environment., the amplitude needs to be 3 dB higher.在 E4438C 上將頻率設置為 859.45MHz ,打開 RF 輸出和調制功能,自定義波形為 16QAM 。振幅的設置要將-111dBm 的固定值和路徑衰減值加在一起。在高低溫測試中, -111dBm 固定值需要改變?yōu)?/p>
47、 -108dBm 。On the Hyperterminal, send the following Berbug commandsFRA 3 (This sets up a 3:1 45ms frame)輸入 FRA 3 命令設置 3:1 45msRX FREQ 859.45 (This sets the receive frequency at 859.45 MHz)輸入 RX FREQ 859.45 這個接收頻率RX BER (This puts the radio under test in slotted receive mode)輸入RX BER 命令將誤碼率跟蹤放入接收模式中MO
48、D RX (This configures the radio under test to receive mode)輸入MOD RX 命令將手機轉入接收模式GO 16 (Begin displaying frame measurements according to DISPLAY settings. 16 frame measurements will be taken and results output to screen continuously until ESC key is pressed.)輸入 GO 16 命令顯示測試結果Read the 1 st value of Ber
49、bug return. This shall be the Rx BER at 859.45 MHz Record down the reading.將第一列的數值也就是BER 誤碼率記錄下來On the Hyperterminal, send the following Berbug commands to stop the test.MOD IDL (This configures the radio under test to idle mode)輸入 MOD IDL 命令將手機轉入待機狀態Repeat the test for the other frequency (937.4937
50、5 MHz) by changing the frequency and amplitude accordingly.在 937.49375MHz 頻率下重復此測試Turn the signal generator RF to off.關閉信號發生器的 RF 發射功能5.12.4 Tx Current TestOn the Hyperterminal, send the following Berbug commandsFRA 3 (This sets up a 3:1 45ms frame)輸入 FRA 3 命令TX FREQ 813.5125 (This sets the transmit
51、 frequency at 813.5125 MHz)輸入TX FREQ 813.5125 命令將手機發射頻率設置為 813.5125MHzTX PSEUDO (This sets the Tx single slot QAM with Pseudo Ramp)輸入TX PSEUDO 命令TRAIN 200000 (This sets the number of frames of TX slots using Pseudo Ramp to 200000 before a full training slot occurs)輸入TRAIN 200000 命令MOD TX (This confi
52、gures the radio under test to transmit mode)輸入MOD TX 命令將手機轉入發射模式From the power supply, read off the current readings. This shall be the Tx current at 813.5125 MHz.通過電源讀取此時發射頻率下的電流值On the Hyperterminal, send the following Berbug commands to stop the test.MOD IDL (This configures the radio under test
53、to idle mode)輸入 MOD IDL 將手機轉入待機模式Repeat the test for the other frequency (901.98125 MHz) by changing the frequency.重復此測試在 901.98125MHz 頻率下測試5.12.5 Tx Frequency Error TestOn the Hyperterminal, send the following Berbug commandsFRA 3 (This sets up a 3:1 45ms frame)輸入 FRA 3 命令TX FREQ 813.5125 (This set
54、s the transmit frequency at 813.5125 MHz)輸入TX FREQ 813.5125 命令將發射頻率設置為 813.5125MHzTX PSEUDO (This sets the Tx single slot QAM with Pseudo Ramp)輸入TX PSEUDO 命令TRAIN 2000000 (This sets the number of frames of TX slots using Pseudo Ramp to 2000000 before a full training slot occurs)輸入TRAIN PSEUDO 200000
55、命令MOD TX (This configures the radio under test to transmit mode)輸入MOD TX 命令將手機轉入發射模式On the N9010A Vector analyzer, Set the center frequency to 813.5125 MHz. by pressingFREQ,Channel, Center Freq, 813.5125, MHz . Set the reference level to 10 dBm by pressing AMPTD Y Scale, 10, dBm . Set the frequency
56、span to 200kHz by pressingSPAN, 200, kHz . Set the resolutionbandwidth (RBW) to 30 kHz by pressing BW, Res BW, 30, kHz. The transmit signal from the unitshould be viewable from the display. To read the frequency of the signal, press Peak Search. Read the signal frequency from the display. This shall
57、 be the Tx frequency at 813.5125 MHz. Frequency error equals measured frequency minus 813.5125 MHz. Express the result in kHz. Record the result.在 9010A 分析儀上通過依次點擊FREQ, CHANNEL, CENTER FREQ 三個按鈕將中心頻率設定為 813.5125MHz ,通過 AMPTD Y SCALE 按鈕將振幅設置為 10 dBm ,通過 SPAN 按鈕將頻率范圍設定為 200KHz ,通過依次點擊 BW, RES BW 兩個按鍵將帶寬解析度設定為 30KHz ,此時發射信號將在屏幕中央顯示出來,點擊PEAK SEARCH 按鍵將 MKR 標記顯示出來,并且將MKR 上面的讀數減去之前設定的中心頻率值就會得
溫馨提示
- 1. 本站所有資源如無特殊說明,都需要本地電腦安裝OFFICE2007和PDF閱讀器。圖紙軟件為CAD,CAXA,PROE,UG,SolidWorks等.壓縮文件請下載最新的WinRAR軟件解壓。
- 2. 本站的文檔不包含任何第三方提供的附件圖紙等,如果需要附件,請聯系上傳者。文件的所有權益歸上傳用戶所有。
- 3. 本站RAR壓縮包中若帶圖紙,網頁內容里面會有圖紙預覽,若沒有圖紙預覽就沒有圖紙。
- 4. 未經權益所有人同意不得將文件中的內容挪作商業或盈利用途。
- 5. 人人文庫網僅提供信息存儲空間,僅對用戶上傳內容的表現方式做保護處理,對用戶上傳分享的文檔內容本身不做任何修改或編輯,并不能對任何下載內容負責。
- 6. 下載文件中如有侵權或不適當內容,請與我們聯系,我們立即糾正。
- 7. 本站不保證下載資源的準確性、安全性和完整性, 同時也不承擔用戶因使用這些下載資源對自己和他人造成任何形式的傷害或損失。
最新文檔
- 小雪古詩課程設計
- 《我國創業板上市公司營運資本管理與盈利能力的關系研究》
- 《不同類型搏克運動參與對蒙古族居民幸福感的影響研究-自我決定動機的調節效應》
- 拓?fù)渑判?課程設計
- 《我國生態環境發展的測度與障礙因素研究》
- 2024-2030年中國汽車機油管行業市場運營模式及未來發展動向預測報告
- 2024-2030年中國水晶輪船模型行業供需狀況發展戰略規劃分析報告
- 2024-2030年中國氧化鋯纖維行業生產現狀分析及投資規劃研究報告
- 2024-2030年中國比例閥行業發展策略及投資前景分析報告
- 2024-2030年中國核電工程建設行業市場分析報告
- 西安交通大學《臨床流行病學》2023-2024學年第一學期期末試卷
- 2024-2025學年人教版高一上冊物理必修一知識清單
- 期末測試卷(一)2024-2025學年 人教版PEP英語五年級上冊(含答案含聽力原文無聽力音頻)
- 2023-2024學年廣東省深圳市南山區八年級(上)期末英語試卷
- 2024廣西專業技術人員繼續教育公需科目參考答案(100分)
- 2024年上海市中考語文備考之150個文言實詞刷題表格及答案
- 2024年漢口銀行股份有限公司招聘筆試沖刺題(帶答案解析)
- 中醫跨文化傳播智慧樹知到期末考試答案章節答案2024年浙江中醫藥大學
- 2024年日歷表(空白)(一月一張-可編輯做工作日歷)
- 廣東省中山市2023-2024學年四年級上學期期末數學試卷
- 2022-2024年國際經濟與貿易專業人才培養調研報告
評論
0/150
提交評論