Ansys實體建模習題及步驟

1、 Ansys 上機操作（第3次）Ansys 實體建模: 由底向上三維實體(連桿 分析實例操作步驟 用由底向上建模技術，練習建立汽車連桿幾何模型。1. 指定的工作目錄，用“c-rod” 作為作業名，進入ANSYS.2. 創建兩個圓形面:Main Menu > Preprocessor > -Modeling- Create > -Areas- Circle > By Dimensions . 輸入RAD1 = 1.4輸入RAD2 = 1輸入THETA1 = 0輸入THETA2 = 180, 然后選擇Apply輸入THETA1 = 45, 然后選擇OK或用命令:/PREP7

2、PCIRC,1.4,1,0,180PCIRC,1.4,1,45,1803. 打開 面號:Utility Menu > PlotCtrls > Numbering .設置面號為 “on”, 然后選擇OK或用命令:/PNUM,AREA,1APLOT4. 創建兩個矩形面:Main Menu > Preprocessor > -Modeling- Create > -Areas- Rectangle > By Dimensions . 輸入X1 = -0.3, X2 = 0.3, Y1 = 1.2, Y2 = 1.8, 然后選擇Apply輸入X1 = -1.8, X

3、2 = -1.2, Y1 = 0, Y2 = 0.3, 然后選擇OK或用命令:RECTNG,-0.3,0.3,1.2,1.8RECTNG,-1.8,-1.2,0,0.35. 平移工作面位置(X=6.5:Utility Menu > WorkPlane > Offset WP to > XYZ Locations +回車后在輸入窗口輸入 6.5 ， OK或用命令:WPAVE,6.56. 設置工作平面所在的坐標系為激活坐標系:Utility Menu > WorkPlane > Change Active CS to > Working Plane或用命令:CS

4、YS,47. 再創建兩個圓形面:Main Menu > Preprocessor > -Modeling- Create > -Areas- Circle > By Dimensions . 輸入RAD1 = 0.7輸入RAD2 = 0.4輸入THETA1 = 0輸入THETA2 = 180, 然后選擇Apply輸入THETA2 = 135, 然后選擇OK或用命令:PCIRC,0.7,0.4,0,180PCIRC,0.7,0.4,0,1358. 在每一組面上分別進行布爾操作:Main Menu > Preprocessor > -Modeling- Oper

5、ate > -Booleans- Overlap > Areas + 先選擇左邊的一組面, 然后選擇Apply再選擇右邊的一組面, 然后選擇OK或用命令:AOVLAP,1,2,3,4AOVLAP,5,69. 激活總體笛卡爾坐標系:Utility Menu > WorkPlane > Change Active CS to > Global Cartesian或用命令:CSYS,010. 定義四個新的關鍵點:Main Menu > Preprocessor > -Modeling- Create > Keypoints > In Active

6、 CS 第一關鍵點, X=2.5, Y=0.5, 然后選擇Apply第二關鍵點, X=3.25, Y=0.4, 然后選擇Apply第三關鍵點, X=4, Y=0.33, 然后選擇Apply第四關鍵點, X=4.75, Y=0.28, 然后選擇OK或用命令:K, ,2.5,0.5K, ,3.25,0.4K, ,4.0,0.33K, ,4.75,0.2811. 激活總體柱坐標系:Utility Menu > WorkPlane > Change Active CS to > Global Cylindrical或用命令:CSYS,112. 創建一條線（由一系列關鍵點擬合一條樣條曲

7、線）:Main Menu > Preprocessor > -Modeling- Create > -Lines- Splines > With Options > Spline thru KPs +順序拾取如圖形窗口所示的六個關鍵點, 然后選擇OK輸入XV1 = 1 (總體柱坐標系，關鍵點1處的半徑Y(jié)V1 = 135 (總體柱坐標系，關鍵點1處的角度XV6 = 1 (總體柱坐標系，關鍵點6處的半徑Y(jié)V6 = 45 (總體柱坐標系，關鍵點6處的角度按OK或用命令:BSPLIN,5,6,7,21,24,22,1,135,1,4513. 通過關鍵點1和18創建一條直線

8、 :Main Menu > Preprocessor > -Modeling- Create > -Lines- Lines > Straight Line + 拾取圖形窗口所示的兩個關鍵點, 然后選擇OK或用命令:LSTR, 1, 1814. 打開線號，顯示線:Utility Menu > PlotCtrls > Numbering .設置 Line numbers為 “on”, 然后選擇OKUtility Menu > Plot > Lines或用命令:/PNUM,LINE,1LPLOT15. 以預先定義的線6, 1, 7, 25 為邊界創建

9、一個新面:Main Menu > Preprocessor > -Modeling- Create > -Areas- Arbitrary > By Lines + 拾取四條線 (6, 1, 7, 和 25, 然后選擇OK或用命令:AL, 6, 1, 7, 2516. 放大連桿左邊部分:Utility Menu > PlotCtrls > Pan, Zoom, Rotate 拾取Box Zoom17. 創建三個線與線的倒角:Main Menu > Preprocessor > -Modeling- Create > -Lines- Line

10、 Fillet +拾取線 36 和 40, 然后選擇Apply輸入RAD = .25, 然后選擇Apply拾取線 40和 31, 然后選擇Apply按Apply拾取線 30和 39, 然后選擇OK按OKUtility Menu > Plot > Lines或用命令:LFILLT,36,40,0.25LFILLT,40,31,0.25LFILLT,30,39,0.25LPLOT18. 以預先定義的圓角為邊界，創建一新的面:Main Menu > Preprocessor > -Modeling- Create > -Areas- Arbitrary > By

11、Lines + 拾取線 12, 10, 和 13, 然后選擇Apply拾取線 17, 15, 和19, 然后選擇Apply拾取線 23, 21, 和24, 然后選擇OKUtility Menu > Plot > Areas或用命令:AL, 12, 10, 13AL, 17, 15, 19AL, 23, 21, 24APLOT19. 把所有的面加起來:Main Menu > Preprocessor > -Modeling- Operate > Add > Areas + 拾取Pick All或用命令:AADD,ALL20. 選擇Fit 使整個模型充滿圖形窗口

12、:Utility Menu > PlotCtrls > Pan, Zoom, Rotate 按Fit21. 關閉線號和面號:Utility Menu > PlotCtrls > Numbering .設置線號和面號為“ off ”, 然后選擇OKUtility Menu > Plot > Areas或用命令:/PNUM,LINE,0/PNUM,AREA,0APLOT 22. 激活總體笛卡爾坐標系:Utility Menu > WorkPlane > Change Active CS to > Global Cartesian 或用命令:CSYS,023. 以X-Z 平面 (在 Y 方向 為對稱面，對面進行鏡面反射: Main Menu > Preprocessor > -Modeling- Reflect > Areas + 拾取Pick All選擇 X-Z 平面, 然后選擇OK或用命令:ARSYM,Y,1324. 把所有的面加起來:Main Menu > Preprocessor > -Modeling- Operate > Add > Areas + 拾取Pic