基于51單片機的溫度檢測系統程序及仿真

1、/*/*用DS18B20進行測量,lcd1602顯示*/*#include "reg51.h"#include "intrins.h"#define uchar unsigned char#define uint unsigned intuchar code table1 ="ID: " /歡迎顯示，包括空格在內<=16uchar code table2 ="Name: "/歡迎顯示，包括空格在內<=16uchar code str1 =" Temperature " uchar c

2、ode str2 =" "/*管腳定義*sbit lcd_rs = P30; /液晶數據命令選擇端sbit lcd_en = P31; /液晶使能sbit DQ = P36; /液晶使能/*參數定義*uint tvalue;/溫度值uchar tflag;/溫度正負標志uchar data disdata5;/*子函數定義*void delay(uchar z); /delay延時子程序void init_lcd(); /LCD1602初始化函數void write_com(uchar com); /LCD1602寫指令函數void write_data(uchar dat

3、e); /LCD1602寫數據函數void lcd1602_display(uchar *q,uchar *p);/LCD1602顯示函數void welcome(); /LCD1602顯示歡迎函數void delay_DS18B20(uint i); /delay_DS18B20函數void Init_DS18B20_display(); /DS18B20初始化顯示void Init_DS18B20(); /DS18B20初始化uchar ReadOneByte(); /DS18B20讀一字節void WriteOneByte(uchar dat); /DS18B20寫一字節Read_Tem

4、perature(); /DS18B20讀取溫度值并轉換void DS18B20_display(); /DS18B20溫度顯示/*主函數*void main()welcome();delay(2000);Init_DS18B20_display();while(1)Read_Temperature();DS18B20_display(); /*delay延時子程序*void delay(uchar z)uchar x,y;for(x=0;x<z;x+)for(y=0;y<114;y+);/*LCD1602初始化函數*void init_lcd()write_com(0x38);

5、/設置16*2顯示，5*7點陣，8位數據接口write_com(0x08); /寫一個字符后地址指針加1 write_com(0x01); /顯示清零，數據指針清零write_com(0x06); /寫一個字符后地址指針加1write_com(0x0c); /關顯示，光標不顯示不閃爍/*LCD1602寫指令函數*void write_com(uchar com)delay(5);lcd_rs = 0; / 選擇寫指令lcd_en = 0; / 將使能端置0P2 = com; / 將要寫的命令送到數據總線上delay(5); / 延時5ms，待數據穩定lcd_en = 1; / 由于初始化已將l

6、cd_en置為0，使能端給一個高脈沖，delay(5); / 延時5ms，待數據穩定lcd_en = 0; / 將使能端置0以完成脈沖/*LCD1602寫數據函數*void write_data(uchar date)delay(5);lcd_rs = 1; / 選擇寫數據lcd_en = 0; / 將使能端置0P2 = date; / 將要寫的數據送到數據總線上delay(5); / 延時5ms，待數據穩定lcd_en = 1; / 由于初始化已將lcd_en置為0，使能端給一個高脈沖，delay(5); / 延時5ms，待數據穩定lcd_en = 0; / 將使能端置0以完成脈沖/*LCD

7、1602顯示函數*void lcd1602_display(uchar *q,uchar *p)write_com(0x80); / 現將數據指針定位到第一行第一個字處while(*q!='0')write_data(*q);q+;delay(1);write_com(0xc0); / 現將數據指針定位到第二行第一個字處while(*p!='0')write_data(*p);p+;delay(1);/*LCD1602顯示歡迎函數*void welcome()init_lcd();lcd1602_display(table1,table2);delay(5000

8、); /*DS18B20初始化顯示*void Init_DS18B20_display()init_lcd();lcd1602_display(str1,str2); /*LCD1602顯示函數*void delay_DS18B20(uint i)while(i-);/*DS18B20初始化*void Init_DS18B20()DQ = 1; /DQ復位delay_DS18B20(4); /延時DQ = 0; /DQ拉低delay_DS18B20(100); /精確延時大于480usDQ = 1; /拉高delay_DS18B20(40);/*DS18B20讀一字節*uchar ReadOn

9、eByte()uchar i,dat = 0;for(i=8;i>0;i-)DQ = 0;/給脈沖信號dat>>=1;DQ = 1; /給脈沖信號if(DQ) dat|=0x80;delay_DS18B20(10);return (dat);/*DS18B20寫一字節*void WriteOneByte(uchar dat)uchar i;for(i=8;i>0;i-)DQ = 0;DQ = dat&0x01;delay_DS18B20(10);DQ = 1;dat>>=1;/*DS18B20讀取溫度值并轉換*Read_Temperature() u

10、char a,b; Init_DS18B20(); WriteOneByte(0xcc); /跳過讀序列號 WriteOneByte(0x44); /啟動溫度轉換 Init_DS18B20(); WriteOneByte(0xcc); /跳過讀序列號 WriteOneByte(0xbe); /讀取溫度 a = ReadOneByte(); b = ReadOneByte(); tvalue=b; tvalue<<=8; tvalue=tvalue|a; if(tvalue<0xfff)tflag = 0;elsetvalue = tvalue+1;tflag = 1;tval

11、ue = tvalue*(0.625); /溫度值擴大10倍，精確到1位小數return (tvalue);/*DS18B20溫度顯示*void DS18B20_display()uchar flagdat;disdata0=tvalue/1000+0x30; /百位數disdata1=tvalue%1000/100+0x30;/十位數disdata2=tvalue%100/10+0x30; /個位數disdata3=tvalue%10+0x30; /小數位if(tflag = 0)flagdat = 0x20; /正溫度不顯示符號elseflagdat = 0x2d; /負溫度顯示負號if(disdata0 = 0x30)disdata0 =0x20;/如果百位為0，不顯示if(disdata1 = 0x30)disdata1 =0x20;/如果百位為0，十位為0也不顯示write_com(0xc4);write_data(flagdat); /顯示符號位write_com(0xc5);write_data(d