挖掘機操作知識

1、挖掘機操作知識挖掘機操作知識Excavator operator knowledgeTable of contents一、挖掘機安全標貼 Safety decals of excavator二、挖掘機操作注意事項 Operator notice of excavator三、挖掘機操作基礎 Operator Basics of excavator3“NOTICE and CAUTION”: 這個詞表示潛在的危險，如果不避免將會導致輕微或中等程度的傷害。 “NOTICE and CAUTION”: This word denote the potential danger, and that mi

2、nor to medium degree of injuries would be caused if failure；“WARNING”:這個詞表示潛在的危險，如果不避免將會導致死亡或嚴重的人身傷害。 “WARNING”: This word denote the potential danger, and that death or serious would be caused if failure；安全標貼Safety decal4“DANGER”:這個詞表示即刻出現的危險，如果不避免將會導致死亡或嚴重的人身傷害。 “DANGER”: This word denote the impe

3、ndent danger, and that death or serious would be caused if failure；“NOTICE and CAUTION”也用于提示提防可能導致人身傷害的不安全操作的有關安全事項 “NOTICE and CAUTION” is also used to indicate the safety information relating to unsafe operations which may cause personal injuries.安全標貼Safety decal5此標貼張貼于發動機機罩上Located near the engin

4、e hood lift switch此標貼張貼于駕駛室內右側玻璃上Located in the cab安全標貼Safety decal6此標貼張貼于駕駛室內右側玻璃上Located in the cab安全標貼Safety decal7此標貼張貼于蓄能器旁的液壓油箱上Located on the hydraulic tank此標貼張貼于駕駛室內右側玻璃上Located in the cab安全標貼Safety decal8該標貼張貼于行走架履帶張緊裝置黃油嘴處Located near the track takeup valve此標貼張貼于水散熱器上部Located near the cool

5、ant filler cap安全標貼Safety decal9此安全標貼張貼于駕駛室內右側玻璃上Located in the cab安全標貼Safety decal10此安全標貼張貼于駕駛室內右側玻璃上Located in the cab安全標貼Safety decal11此標貼位于蓄電池附近Located near the battery安全標貼Safety decal12此標貼位于液壓油箱上Located on the hydraulic tank此標貼位于燃油箱上Located on the fuel oil tank安全標貼Safety decal13此標貼位于燃油箱上Located

6、on the fuel oil tank安全標貼Safety decal14此標貼張貼于駕駛室內右側玻璃上Located in the cab安全標貼Safety decal15此標貼位于蓄電池附近Located near the batter安全標貼Safety decal16此標貼張貼于工具箱外右側Located near the boarding gate安全標貼Safety decal17始終保持逃生錘放置在駕駛室內部。Always keep escape hammer placed inside the cab.注意：如果駕駛室門打不開，采用以下方法脫離：Caution: If yo

7、u can not open the cab door, get out of the cab using the following methods:1. 打開前窗，從前窗脫離 Open the front window and to go out;此標貼張貼于駕駛室后側玻璃上Located in the cab安全標貼Safety decal182.如果打開前窗比較困難，用錘子打破玻璃脫離If you open the front window is difficult, to break the glass with a hammer and out.3.如果不能從前窗脫離，用錘子打破后

8、窗玻璃脫離If you can not go past the front window, to break the rear window with a hammer and out 安全標貼Safety decal19注意：機器操作時請遠離機器Caution: keep clear of machine during operation此標貼張貼于斗桿左右側板上Located on the arm此標貼張貼于配重后部Located on the counterweight安全標貼Safety decal20此標貼張貼于發動機導風罩上Located near the engine fan注意

9、：當發動機風扇停止運轉后才可對風扇及導風罩進行維修Caution: keep clear of or stop engine before servicing安全標貼Safety decal21此標貼張貼于駕駛室內切斷閥旁左扶手箱上Located on the left arm注意：在駕駛室內休息或整機停止動作較長時間時，需將切斷閥關閉，防止手臂及腳不小心碰到手先導、腳先導。離開駕駛室前必須確保切斷閥為關閉狀態Caution: To prevent the arms or legs hit the hand pilot, foot pilot accidentally, you must cl

10、ose shut-off valve when you have a rest in the cab or stop the machine for a long time. You must ensure that shut-off valve is turned off before leaving the cab .安全標貼Safety decalTable of contents一、挖掘機安全標貼 Safety decals of excavator二、挖掘機操作注意事項 Operator notice of excavator三、挖掘機操作基礎 Operator Basics of

11、excavator23l油、水檢查 Check oil、 water l逐個地檢查液壓油位、發動機冷卻水箱水位、發動機機油油位和回轉馬達齒輪油油位是否處于正常位置，如不是須增加或減少油或水使其達到正常位置。 Check hydraulic oil level ,coolant level ,the oil level of the Engine and the swing reduction gear oil is in normal position，If it is not, must increase or reduce it to its normal position.1.操作前注意

12、事項操作前注意事項 Notice before operate the excavator24l在柴油和機油處嚴禁煙火 Fireworks is strictly prohibited機油、防凍液、特別是柴油屬于高度易燃物，所以不要讓煙火接近機器。Engine oil, coolant ,especially diesel oil are highly inflammable materials，so dont let fireworks near machine.添加柴油之前要先關閉發動機。Turn off the engine before adding diesel.1.操作前注意事項操

13、作前注意事項 Notice before operate the excavator25l上下機器 Getting on or off the machine上下機器時，面向機器，使用扶手及腳踏，要保持與整機三點接觸。Face the machine when getting on or off the machine, use handrails and pedal ，touch at three points simultaneously to ensure stability of the body.不要抓握控制桿Prohibit grip pilot control rod.檢查并清潔

14、扶手、踏板Check and clean the handrails, pedal.1.操作前注意事項操作前注意事項 Notice before operate the excavatorl檢查障礙物 Check the obstacles依次檢查整機上、下、左、右、前、后，及時將雜物、工具及障礙物清除。Check the machine in turn, down, left, right, front, back, remove debris, tools and obstacles promptly.1.操作前注意事項操作前注意事項 Notice before operate the e

15、xcavatorl確認車體方向 Confirm the direction of the body左、右、前、后方向是由駕駛室在前，行走馬達在后決定的Left, right, front and rear direction is determined by facing the front of the cab, travel motors are in the rear of the machine.1.操作前注意事項操作前注意事項 Notice before operate the excavatorl檢查照明系統 Check lighting system晚上操縱整機時，檢查所有照明設

16、備，確保照明系統完好Control machine at night, check all lighting equipment to ensure lighting system are good ;28l啟動前按喇叭警示 Press the horn to warn before starting 啟動前按響喇叭以警告機器周圍的人員 。 Press the horn to warn personnel around the machine before starting.l讓其他人遠離機器 Let other people away from the machine嚴禁除操作者外其他人爬上

17、整機，因為這樣做會導致嚴重的傷害。It is strictly prohibited other than the operator who climbed up the machine, because it would result in serious injury.2.啟動時注意事項 Notice when you start excavator29l啟動發動機 Start engine柴油機起動前，鑰匙開關先打到“START ”檔，發動機第一次沒有順利啟動，請稍等15秒鐘后再啟動，連續三次啟動不成功需等待2分鐘后再啟動。如每次停機后都存在此問題，必須排除故障。Before start

18、ing the engine, first turn the key switch to START position, if the engine havent started smoothly one time, please wait 15 seconds and then start again, if three consecutive unsuccessful start occur, then wait for 2 minutes to start again. If every time after shutdown the engine will meet start eng

19、ine problem, you must do troubleshoot.2.啟動時注意事項 Notice when you start excavator30通過啟動電機通電運轉以帶動發動機起動時，啟動過程持續15秒。發動機起動后立即放松鑰匙，為避免起動器的損壞,每次操作馬達起動器不可超過10秒。若啟動時間持續過長，將有可能燒壞啟動電機。Start motor is driving the engine start to run, the start process lasted from 1 to 5 seconds. Release key immediately after the

20、engine starts to run, to avoid damage the starter, each operation must not exceed 10 seconds. If the start-up time continued too long, will the start motor may burn.2.啟動時注意事項 Notice when you start excavator31l啟動時怠速暖機 Idle warm-start發動機起動后不應立即加大油門，在天氣冷時要怠速運行35分鐘，對發動機進行預熱，再逐漸加大油門。這樣將防止因發動機燃燒不充分導致的在燃燒室

21、缸壁積碳。Should not immediately accelerate engine at high speed, after start the engine let engine throttle in the idle when running 3 to 5 minutes to warm up the engine, and then gradually increase the throttle. This will prevent the engine due to incomplete combustion carbon in the combustion chamber

22、cylinder sleeve.2.啟動時注意事項 Notice when you start excavator32起動后要熱機To warm the engine properly after starting l啟動后檢查機油壓力 Check the engine oil pressure after startup挖掘機啟動后，檢查監控器機油壓力顯示，整機須在啟動15秒內建立起機油壓力，若15秒后機油壓力還未建立，則應立即關閉發動機。在排除故障之前不要起動發動機。Excavator started, check the oil pressure on monitor display,

23、the machine must to establish oil pressure within 15 seconds after start, if oil pressure has not been established after 15 seconds , immediately turn off the engine. Do not start the engine before troubleshooting.2.啟動時注意事項 Notice when you start excavator33l 挖掘機起動后，禁止人員從工作裝置下部通過； After the excavator

24、 starts, forbids the personnel to pass from the work attachment;l機器長距離行走，支重輪、托鏈輪內部由于長時間旋轉，產生高溫，行走馬達需位于整機后邊。行走時，須經常停車冷卻。這可以改善輪子內部的潤滑，并能延長下部車體的壽命。 If machine travel a long distances, upper track roller, lower track roller will create high temperature through rotating for long time, running the motor m

25、ust be located behind the machine. Traveling with frequent stopping cooling can improve the lubrication of the roller, and can prolong the service life of the undercarriage.長途行走時，請每行走20分鐘休息5分鐘，以免損壞行走馬達。Long distance traveling , traveling 20 minutes, stop for every 5 minutes in order to avoid damage

26、to the motor running.3.操作時注意事項 Notice when you operate excavator34l高轉速時確認自動怠速功能 High-speed automatic idle function confirmed在自動怠速功能開著時，必須密切注意發動機控制旋扭的設定。當發動機控制旋扭的設定速度高時，如果操作者沒有注意高的發動機速度設定就操作操縱桿，發動機速度的突然增大會引起機器的加速運動，有可能導致人員的嚴重受傷。When the automatic idle function working, you must pay high attention to

27、the engine throttle switch setting. When the engine speed throttle switch set at high speed, if the operator does not notice the high engine speed is set, and to operate the joystick, the engine speed of the machine will cause a sudden increase of acceleration, and the suddenly motion of machine may

28、 result in serious injury.3.操作時注意事項 Notice when you operate excavator35l絕對不要試圖橫穿坡度大于15度的斜坡，防止機器側翻。 Never attempt to cross slope greater than 15 degrees slope, to prevent the machine over roll.3.操作時注意事項 Notice when you operate excavator36l防止倒車和回轉時的受傷事故The prevention of reverse traveling and swing hit

29、ting accident injuries l不要讓其他人接近整機的行走或旋轉區域Do not let other people walking near the machine or rotary area.l如果操作區域危險或視線不良時，必須另外有人指揮方向。If the operating area dangerous or poor visibility, must also command the operate by some people.3.操作時注意事項 Notice when you operate excavator37l 與高壓電線保持安全距離 Keeping a s

30、afe distance from high voltage wires 在電線附近操作時，不可把機器的任何部分或負載靠近電線。濕地將增大人員可能觸電的范圍。讓周圍人員遠離作業區。 When operation near the wire, not to let any part of the machine or the load close to the wire. Wetlands will increase the range of personnel may shock. Let those around away from the work area.3.操作時注意事項 Notic

31、e when you operate excavator38l 小心廠房等高架設施 Care factories and other facilities 如果機器的工作裝置或其它部分撞到廠房頂部等高架物，機器和高架物都會損壞，還可能造成人員受傷；小心防止動臂或斗桿與廠房頂部等高架物相撞。 If the machines work attachment or other parts of the plant hit the top of the other elevated objects, objects which can damage the machine and elevated,

32、and may cause injury; care to prevent the boom or bucket at the top bar and plant materials such as overhead collision.3.操作時注意事項 Notice when you operate excavator39l操作時關注整機報警 Concerns the alarm of machine when operation 挖掘機操作過程中，若監控器發出報警聲，則應立即關閉發動機，然后將電鎖開至“ON”檔，通過監控器檢查故障記錄，確定報警聲音來源（機油壓力報警、液壓油溫報警、冷卻液

33、水溫報警、冷卻液水位報警），并找相應人員對其進行處理。在排除故障之前不要起動發動機。 When excavator operating, if the monitor alarm sound, they should immediately turn off the engine, and then open the electric lock to ON position, check the fault information on monitor to determine the source of the alarm sound (engine oil pressure alarm,

34、hydraulic oil temperature alarm , coolant temperature warning, coolant water level alarm), and find the appropriate staff to process it. Do not start the engine before troubleshooting.3.操作時注意事項 Notice when you operate excavator40l行走時注意事項 Traveling notice在平坦的地面上行走時，要收回工作裝置并與地面保持40cm-50cm距離。Traveling

35、on flat ground, we must recover the device and work with the surface 40cm-50cm distance.3.操作時注意事項 Notice when you operate excavator41盡可能避免在障礙物上行走。如果整機不得不在障礙物上行走。要使工作裝置靠近地面且低速行駛。 As far as possible avoid traveling on barrier. If the machine had to walk on an obstacle. To make the unit close to the gr

36、ound and low speed.3.操作時注意事項 Notice when you operate excavator42當上坡行駛時，要使工作裝置保持距地面20cm-30cm。在緊急情況下，可以迅速將工作裝置降至地面以幫助停止整機。 When driving uphill, to make working devices to keep away from the ground 20cm-30cm. In an emergency, you can quickly lowered to the ground working device to help stop the machine

37、.3.操作時注意事項 Notice when you operate excavator43當下坡行駛時，要使工作裝置保持距地面20cm-30cm。 While downhill driving, keeping the working device apart from the ground 20cm-30cm.3.操作時注意事項 Notice when you operate excavator44在斜坡行走應小心操作Be careful walking on slopes當行駛在斜坡上時，轉彎速度比較快，很難控制機器，所以應避免在下坡時轉彎。假如必須轉彎，首先停止機器，在左轉時，向后轉動

38、左履帶；右轉時，向后轉動右履帶，這種方法可以降低在斜坡上轉彎的危險性。When traveling on a slope, the turning speed is fast, very difficult to control the machine, it should be avoided when going downhill turn.If it needs to turn, first to stop the machine, when turning left, turning back the left track; right time, turning back the r

39、ight track, this method can reduce the risk of turning on the slopes.3.操作時注意事項 Notice when you operate excavator45將機械停放于地面上。 The machine is at rest on the ground.將鏟斗降至地面。 Bucket down to the ground.以怠速運行發動機分鐘。 Run the engine at idle speed for 3 minutes.4.停機時注意事項Notice when you stop excavator46拉上先導控制關

40、閉桿將一切操作桿鎖至中位。Pull the pilot cut off level and put all the pilot control level at nurture position.轉鑰匙開關至“”位置。從開關上拿掉鑰匙。如果發動機沒有被正確地關掉，渦輪增壓器可能被損壞。 Turn key switch to 0FF position. Remove the key from the switch. If you have not been properly turned off the engine, the turbocharger may be damaged.4.停機時注

41、意事項Notice when you stop excavator47如果必須將整機停放在斜坡上，要將鏟斗調整到下坡一側，將鏟斗插入地面。并在履帶的下面放上墊塊以防止整機移動。 If the machine must be parked on a slope, adjust to the downhill side of the bucket, put the bucket into the ground. Placed in the track pad underneath to prevent the machine moving.4.停機時注意事項Notice when you stop

42、 excavator48l檢修時警告 Warning when maintenance 在檢查/故障處理時，如果有人啟動發動機或操作操縱桿，可能會導致嚴重的傷害。因此當人離開整機時，務必要在操縱桿上懸掛“禁止操作”警示牌。 During the inspection / troubleshooting, if someone start the engine or operating the joystick, can cause serious injury. So when people leave the machine, must be sure to hang No Operatio

43、n warning signs.5.檢修時注意事項Notice when you maintenance excavator49l檢修時應關閉發動機 Stop engine when maintenance 在發動機運轉時進行檢查/故障處理，手或衣服可能被風扇、帶輪或風扇皮帶夾住。When the engine is running checking/ troubleshooting, hands or clothing may be gripped by the fan, pulley or fan belt.5.檢修時注意事項Notice when you maintenance exca

44、vator50l整機處于高溫或高壓時的檢修注意事項Notice when machine is high temperature or high pressure at the time of inspection整機剛停止時，發動機的冷卻水和機油都處于高溫。在此情況下如果打開蓋子或更換機油，可能會被高溫的水或機油燙傷。 Machine just stopped, the engine cooling water and oil are in high temperatures. In this case, if you open the cover, or change the oil, m

45、ay be scalding hot water or oil.5.檢修時注意事項Notice when you maintenance excavator51l小心高壓油Careful high pressure oil在正常情況下，每一條液壓油管都存在壓力，所以在釋放內部壓力之前，先不要補充油或清除油，或檢修整機。因為高壓油會對皮膚和眼睛造成傷害。 Under normal circumstances, there each hydraulic tubing pressure, so before the internal pressure is released Do not add o

46、il or clean oil, or repair machine. Because the high pressure oil will damage the skin and eyes.5.檢修時注意事項Notice when you maintenance excavatorTable of contents一、挖掘機安全標貼 Safety decals of excavator二、挖掘機操作注意事項 Operator notice of excavator三、挖掘機操作基礎 Operator Basics of excavator操縱機構Control Mechanism1.操縱機構

47、Control mechanism駕駛室門開鎖桿 Cab door lock rod; 先導切斷閥控制桿 The pilot shut-off valve control lever; 左方控制桿/喇叭按鈕 The left lever / horn button; 左行走操作桿 Left-lateral lever; 左行走踏板 Walk left pedal; 右行走踏板 Walk the right pedal;右行走操作桿 Right-lateral operation Bar; 右方控制桿/瞬時增力按扭 The right lever / button instantaneous F

48、orce;手先導方向與動作Hand movement direction of the pilot 左手先導閥 右手先導閥The left hand pilot : The right hand pilot:前：斗桿放出 前：動臂下降 Before: Arm out Before : Boom down后：斗桿收回 后：動臂上升 After: Arm in After : Boom up 左：整機逆時針回轉 左：鏟斗收回 Left: Left swing Left: Bucket in右：整機順時針回轉 右：鏟斗放出 Right: Right swing Right: Bucket outBe

49、foreBeforeAfterAfterLeftLeftRightRight1.操縱機構Control mechanism2.機器方向 Vehicle DirectionLeft, right, front and rear direction is determined by facing the front of the cab, travel motors are in the rear of the machine后 After前 Before左 Left右 Right行走馬達 Travel motor3.儀表按鈕 Instrument button該顯示器主要由報警指示燈、液晶顯示屏

50、、鍵盤三部分組成。該顯示器主要由報警指示燈、液晶顯示屏、鍵盤三部分組成。 The display mainly by the warning light, LCD display and key switch in three parts報警指示燈Alarm Indicator液 晶 顯 示 屏LCD鍵盤Key switch液晶顯示器LCD Monitor普通操作界面commonly operating interface 1.工作小時計，累計機器工作時間，當小時計圖標閃動時說明正在計時； Working hours, for total working time machine, when

51、the hour meter icon flashes to indicate the time; 2.發動機冷卻水溫監控表，紅色段表示水溫過高，綠色段表示水溫處于正常溫度范圍；The engine cooling water temperature monitoring chart, the red states that the water temperature is too high, the green section that the water temperature in the normal temperature range; 3.燃油油位監控表，紅色段表示油位過低，綠色段

52、表示油位處于正常工作范圍； Fuel oil level monitoring tables, the red states that the oil level is too low, the green section that the oil level in the normal scope of work; 1234567液晶顯示器LCD Monitor普通操作界面commonly operating interface 4.系統工作電壓，正常工作電壓范圍為18V32V； The system voltage, the normal operating voltage range o

53、f 18V 32V; 5.發動機工作檔位，檔位范圍為110檔； The engine stalls, stalls range from 1 to 10 stalls; 6.行走高低速，兔子表示走快速檔，烏龜表示走低速檔； Walking high and low speed, The rabbit that file to go fast, the turtle that take the low speed; 7.信息提示區 ，正常工作狀態下該區域顯示當前的日期與時間；當有報警信息及其他信息出現時該區域顯示報警提示；有多條報警信息時，循環顯示。 Message alert area, th

54、e normal working condition of the area shows the current date and time; when the alarm information and other information appears in the region shows alarm; a number of alarm information, the circular display.1234567123報警Alarm全部亮起界面 Interface with all indicators turning報警狀態界面 Alarm status interface 液

55、晶顯示器LCD Monitor1231.吊裝功能，功能取消時不顯示該圖標；Lifting function: this icon shall not appear when the function is canceled;2.瞬時增力，取消瞬時增力功能時不顯示該圖標；The instantaneous growth force, cancel the function of the instantaneous force increasing the icon is not displayed;3.自動怠速，取消時不顯示該圖標；Automatic idle, the icon does no

56、t show canceled;液晶顯示器LCD Monitor12435678鍵盤Key switch圖標圖標開關開關功能功能1蜂鳴器取消按鍵 當報警蜂鳴器響起時按下此開關可以停止報警蜂鳴器響 2向上按鍵 選擇上側的項目（在頂側項目之后選擇底側項目） 3菜單按鍵 選擇進入主菜單界面 4返回按鍵 返回上一個界面 5確認按鍵 進入選擇/設置項目 6向右按鍵 選擇右側的項目 7向下按鍵 選擇下側的項目（在底側項目之后選擇頂側項目） 8向左按鍵 選擇左側的項目 12435678鍵盤Key switchIconSwitchFeatures1Cancel button buzzerWhen the bu

57、zzer sounded the alarm, press the switch to stop the alarm buzzer2Up buttonChoice of side projects (selected in the top side of the project after the end of side item)3Menu buttonChoose to enter the main menu interface4Back ButtonReturn to the previous screen5Confirm buttonInto the selection / setti

58、ng item6Right buttonSelect the right projects7Down buttonSelect the next side of the project (in the bottom side of the project, chose the top side of the project)8Left buttonSelect the items left控制開關面板和收音機Control switch panel and radio1.開關盒The switch box 2.收音機 Radio 3.油門位置開關及點火開關 The throttle posit

59、ion switch and the ignition switch 4.前窗洗滌開關 The front window washer switch5.備用開關 Standby switch開關盒Switch BoxS1:行走速度控制開關 walking speed control switch:機器默認低速檔，“烏龜”燈亮。按壓開關即可轉換到高速檔，“兔子”燈亮，“烏龜”燈滅。再次按壓開關即可轉換到低速檔，“烏龜”燈亮，“兔子”燈滅。 Default low speed machine, turtlelight LED1 on. Press this switch to switch to

60、high gear, Rabbitlight LED2 light, turtlelight LED1 off. Press this switch again to switch to low gear, turtlelight LED1 light, Rabbitlight LED2 offS2:工作燈開關 Work light switch該開關控制動臂燈和車架燈工作。兩個指示燈指示工作燈的工作情況： The switch lights and boom frame lights work. Two work lights LED indicates the work:1),一次按壓開關