目視檢驗員培訓大綱

ASMEProceduresJDB/ASME-12

JDBWrittenPracticeforTraining,Rev.0

ExaminationandCertificationofVisual

Page：1of4

ExaminationPersonnel

WrittenParticeforTraining,ExaminationandCertificationofVisual

ExaminationPersonnel

目視檢驗員培訓、考試及資格鑒定管理程序

PreparedbyDate

編制：日期：

ApprovedbyDate

批準：日期：

AcceptedbyDate

認可：日期：

***************SubsidiaryEquipmentCo.,Ltd.

****\'(*火火*火***火*

ASMEProceduresJDB/ASME-12

WrittenPracticeforTraining,ExaminationRev.0

JDBandCertificationofVisualExamination

PersonnelPage：2of4

目視檢驗員培訓、考試及資格鑒定管理程序

1.0General總則

Thisproceduredescribestherequirementfortrainingandtheexaminations

andcertificateofVEpersonnel.

本大綱規定了從事ASME規范產品目視檢驗人員的考試方法.

2.0REQUIREMENT要求

AllpersonnelperformingvisualexaminationsinJDBwillbequalifiedasfollows.

本公司所有的目視檢驗人員都應按下列方法進行評定：

2.1Instructioninthefundamentalsofthenon-destructiveexaminationmethod-visual

examinationbyQCEngineer.

由檢驗工程師對其進行無損檢驗方法-目視檢驗的基礎知識指導.

2.2Aminimumof20hourson-the-jobtraininginordertofamiliarizetheVisual

Examinerwiththeappearanceandinterpretationofindicationsofwelddefects

byQCEngineer.

檢驗工程師應對目視檢驗人員進行至少20小時的現場培訓，以使其熟悉焊接缺陷

的外觀及解釋.

2.3PriortobeingdesignatedasaVisualExaminer,theindividualshallreceivean

eyeexaminationbyaqualifiedindividualandbeabletoreadaJeagerType

No.1StandardChartatadistanceofnotlessthantwelve(12)inches(300mm)

andcapableofdistinguishinganddifferentiatingcontrastbetweencolorsused.

Thisshallbeconductedannually.

ASMEProceduresJDB/ASME-12

JDBWrittenPracticeforTraining,ExaminationRev.0

andCertificationofVisualExamination

PersonnelPage：3of4

目視檢驗員培訓、考試及資格鑒定管理程序

在被認命為目視檢驗員之前，該人應接受有資格人員對其進行的視力檢查，并且

他（她）能在不小于12英寸的距離之外讀出Jeager標準視力表1號字，且能區分和辨

別所用顏色間的不同.此種檢查應每年一次.

2.4PriortobeingqualifiedasaVisualExaminer,theindividualmustreceivea

passinggrade（minimumof80%）onanoralconsistingof10questionson

visualexaminationmethods,appearances,andinterpretationofindicationsof

welddefectsbyQCManager.

在被評定為合格的目視檢驗員之前，質量經理對該人進行口頭考試（至少80分以上

合格）.試題共10道，包括焊接缺陷的目視檢驗方法、外觀、解釋等.

2.5Uponsatisfactorycompletionwithapassinggradetheindividualwillbecertified

inwritingthatheisaqualifiedVisualExaminerbytheQCManager.

考試合格后，由質量經理書面認證該人為評定合格的目視檢驗員.

3.0REQUALIFICATION重新認證

3.1Re-qualificationwillberequiredwhenthereisspecificreasontoquestionthe

abilityoftheindividualtoperformvisualexamination,orwherethereare

substantialchangesinvisualexaminationproceduresorequipment.

當有特殊原因懷疑某人執行目視檢驗的能力或當目視檢驗規程或設備有實質性改

變時，要求對其人重新進行評定.

3.2AlltheVisualExaminersshallbere-certifiedtrienniallybyQCManagerin

accordancewithoneofthefollowingcriteria:

所有的目視檢驗人員每隔三年都須重新認證.由質量經理按下列標準進行：

ASMEProceduresJDB/ASME-12

WrittenPracticeforTraining,ExaminationRev.0

JDBandCertificationofVisualExamination

PersonnelPage：4of4

目視檢驗員培訓、考試及資格鑒定管理程序

(1)Evidenceofcontinuingsatisfactoryperformance.

具有連續的令人滿意的工作表現的證明

(2)Re-examinationinparagraph2.4deemednecessarybyQCManager.

當質量經理認為必要時，2.4節所述考試也應重新進行.

4.0PROGRAM程序

TheVisualExaminercandidatemustreceive8hourstrainingbyQCEngineer

inthefundamentalsofvisualexamination;thisshallincludeasaminimumthe

following:

目視檢驗員必須接受8小時的目視檢驗基本知識指導.至少應包括：

(a)Instructioninweldgeometry.焊縫幾何形狀的指導.

(b)Instructionsinundercut,lackoffusion,lackofpenetration,slaginclusion,

excessiveweldreinforcementandlackoffill,etc.WeldingProcedure

SpecificationswillbeexplainedtotheVisualExaminerandtheneedtoweld

withintheparametersoftheWeldingProcedureSpecificationshallbe

delineated.Thetraineewillunderstandhowtodetermineifproperwelding

material,electricalcharacteris