完整版電氣試驗中英文

1、電氣試驗 Electric Test1. 電氣試驗常規要求 General Requirements1) 電氣預防性的試驗嚴格按規范、產品說明書要求執行。Electric preventive test shall be carried out in accordance with criterion and product specification strictly.2) 組合式微機保護及監控繼電器按產品說明書進行整定。Adjust combined micro-computer protection and monitoring relay3) 常規的電磁式繼電器調試按新編保護繼電器檢驗

2、中有關規定進行調試。The normal electromagnetic relay commissioning shall comply with the stipulations ofNewProtection Relay Test.4) 盤(柜 )指示電表經校驗后，對合格的電表粘貼專用合格證。After calibration of the panel (cabinet) indicative ammeter, paste special quality certificate on the qualified ammeter.5) 高壓開關柜的傳動試驗在各電氣元件及單體柜調試后進行。

3、傳動試驗時， 認真核對 各回路的準確及可靠性。主要傳動試驗項目：High pressure switchboard transmission test shall be carried out after electrical element and individual cabinet commissioning. Check the loops accuracy and liability during transmission test. The main transmission project ：操作控制回路傳動試驗；Operation Control Loop Transmissi

4、on Test保護回路傳動試驗；Loop Protection Transmission Test測量 /計量回路試驗；Measure/Recording Loop Test 系統低電壓、斷線保護試驗；System Low Pressure, Cable break protection test核對一、二次相位；Check 1st and 2nd phase2. 變壓器試驗 Transformer Test1）測量繞組連同套管的直流電阻，測量應在各分接頭所有位置上進行；Measure wi ndi ng and sleeve DC resista nee of all the connect

5、ion joi nts.2）對1600kVA及以下三相變壓器，各相測得值的相互差值應小于平均值的4%,線間測得值的相互差值應小于平均值的2%； 1600kVA以上的三相變壓器，各相測得值的相互差值應小于平均值的2%，線間測得值的相互差值應小于平均值的1% ； 1600kVA以上的三相變壓器，各相測得值的相互差值應小于平均值的2%，線間測得值的相互差值應小于平均值的1%；（重復）三相電阻不平衡率計算Three Phase Transformer of 1600Kva and the less, the measured value s differenee shall be4% less tha

6、 n the average, intern al li nes measured value shall be 2% less tha n the average.Three Phase Transformer of above 1600kVA, the measured value differenee shall be 2% less tha n the average, intern al li nes measured value shall be 1% less tha n the average, Three Phase resista nceUn bala nee Rate c

7、alculati on formula:不平衡率三相實測最大值最小值三相算術平均值100%Measured Max-Mi nUn bala need Rate= 100%Average3）直阻測量方法：DC Resista nee Measure Method用感性負載速測歐姆計測量繞組直流電阻時，其接線及測量方法應符合測試 儀器的技術要求。When measuri ng winding DC resista nee by sen sibility load ohmmeter, the connection and the measure method shall comply with eq

8、uipme nt tech ni cal requireme nts.4）變壓器的直流電阻，與同溫下產品出廠實測數值比較，相應變化不應大于2%;將不同溫度下的繞組直流電阻溫度換算到同一溫度：DC resista nee of tran sformer, compared with measured value of product by manu faeturer un der same temperature, the corresp onding cha nge shall be not more tha n 2%, convert the winding DC resista nee u

9、n der differe nt temperature into the same temperature.RxRaTtxTta（式中：Rx -換算至溫度為tx時的電阻； Ra溫度為ta時所測得的電阻；T-溫度 換算系數，銅線為235，鋁線為225; tx-需要換算Rx的溫度；ta-測量Ra時的溫度）（convert Rx into the resista nee un der temperature of tx, Ra is resista nee un der temperature of ta, T is temperature convert coefficie nt, copper

10、 line is 235, alu minum is 225, tx is the temperature of Rx to con vert, ta is temperature of measuri ng Ra ）5）由于變壓器結構等原因，差值超過本條第款時，可只按本條第款進行比較。Cause of tran sformer structure, the differe nee is more tha n clause 2, comply with clause 4 on ly.6）檢查所有分接頭的變壓比變壓比與制造廠名牌數據相比應無明顯差別，且符合變比的規律。額定分接的變壓比允許偏差為）

11、.5%，其它分接的偏差應在變壓器阻抗值（%）的1/10以內，但不超過 1%。Check all connection joints transforming ratio, which shall be no distinet differenee compared with the date of manu facturer brand and comply with the tran sform ing rule. Rated tap tran sform ing ratio allowable differe nee is0.5%, others shl within 1/10 of tr

12、an sformerresista nee （%）, but not more tha n 1%.7）檢查三相變壓器的結線組別和單相變壓器引出線的極性Check three phase transformer wire series and polarity of single phase transformer output wire.8）測量繞組連同套管的絕緣電阻Measure the in sulati on resista nee of winding and sleeve.a）絕緣電阻值不應低于出廠試驗值的70%。In sulati on resista nee shall be n

13、ot less tha n 70% of leave factory testi ng value.b）當測量溫度與產品出廠試驗時溫度不符合時，可按下表?yè)Q算到同一溫度時的數值進行比較：If any unconformity between measured temperature and leaving factory test ing temperature, convert into same temperature accord ing below table and compare:溫度差TemperatureDiffere neeK51015202530354045505560換算系

14、數Con verti ngA1.21.51.82.32.83.44.15.16.27.59.211.2Coefficie nt（注：表中K為實測溫度減去20C的絕對值）(Remark: K is the absolute value of measured temperature minus 20 C )c) 當測量絕緣電阻的溫度差不是表中所列數值時， 其換算系數按下列公式計算： when temperature difference of measuring insulation resistance value can not be found in the above table, th

15、e converting formula is ：A=1.5K/10當實測溫度為 20 C以上時：When measured temperature is above 20CR20=AR t當實測溫度為 20 C以下時：When measured temperature is below 20 CR20=Rt/A(式中：R20-校正到20C時的絕緣電阻值；Rt-在測量溫度下的絕緣電阻值)(R20- revise to absolute value of 20C , Rt- is the absolute resistance vale under measuring temperature)9

16、) 交流耐壓試驗 AC Withstand V oltage Test根據制造廠提供的技術資料及業主的要求決定是否進行該項試驗；如進行該項 試驗需制造廠提供試驗電壓值。 In accordance with the technical documents provided by manufacturer and Clien ts requirements to determine whether to carry out thetest, if do it, the manufacture should provide test voltage value.a) 試驗電壓的頻率為 50Hz，電

17、壓波形應盡可能接近正弦波形。The testing voltage frequency is 50Hz, voltage wave form better be sine wave.b) 進行交流耐壓時 ,非被試側繞組應短接后接地。Carry out AC withstand voltage test, the un-test side of the winding resistance should be earthed.10) 測量與鐵芯絕緣的各緊固件的絕緣電阻measure the resistance of iron coreinsulation fastening warea) 應測

18、量可接觸到的穿芯螺栓、軛鐵夾件及綁扎鋼帶對鐵軛、鐵芯及繞組壓環的絕緣電阻；Measure the touchable penetration bolt, yoke clamp, steel banding yoke, steel core and winding ring insulation resistance.b) 采用 2500V 兆歐表測量，持續時間為 1 分鐘，應無閃絡及擊穿現象；measuring with 2500 ohmmeter, tine last 1minute, no flashover, no breakdown.c) 當軛鐵梁及穿芯螺栓一端與鐵芯相連時，應將連接片

19、斷開后進行試驗；When one side of yoke beams and penetration bolts connected with the core, carry out Test after disconnecting the clips.11) 沖擊合閘試驗 Impact Closing Test在額定電壓下對變壓器進行沖擊合閘試驗,應進行 5 次,每次間隔宜為 5 分鐘,無異?，F(xiàn)象。沖擊合閘試驗宜在變壓器高壓側進行；對中性點接地的電力系統，沖擊 試驗時變壓器的中性點必須接地； 發電機變壓器組中間連接無操作斷開點的變壓器， 可不進行沖擊合閘試驗。Carry out impac

20、t closing test under rated voltage for 5 times every 5 minus, there should be no abnormal phenomenon. Impact closing test shall carry out at high pressure side of transformer. The neutral point must be grounded for power system with neutral grounding. No impact closing test is acceptable for the gen

21、erator transformer assembly without operation disconnection point.12) 檢查相位 Phase Check檢查變壓器的相位必須與系統相位一致。Confirm the transformer and the system phase must be consistent.3. 電纜試驗 Cable Test1) 絕緣測試 Insulation Testa) 測量電纜對地或?qū)饘倨帘螌娱g和各線芯間的絕緣電阻。Measure the insulation resistance of cable to ground or iron sh

22、ielded layer and cores.b) 對 1kV 以上電纜采用 2500V 兆歐表。Use 2500V Megohmmeter to test cable of above 1kVc) 對 0.6/1kV 及以下電纜采用 1000V 兆歐表。Use 1000V Megohmmeter to test cable of 0.6/1Kv and below.2) 直流耐壓及泄漏電流測量DC Voltage Endurance and DC Leaking Measuring(塑料絕緣電纜包括聚氯乙烯絕緣電纜、聚乙烯絕緣電纜及交聯聚乙烯絕緣電纜。 聚氯乙烯絕緣電纜產品型號有 VV 、V

23、LV 等；聚乙烯絕緣及交聯聚乙烯絕緣電纜 的產品型號有 YJV 及 YJLV 等。 )Plastic insulation cable including PVC insulation cable, polyethylene insulation cable and cross-linked polyethylene insulation cable電纜額定電壓（U 0）Cable Rated Voltage直流試驗電壓DC Test Voltage試驗時間（min）TestingTime3.6kV15kV156kV24kV158.7kV35kV153）試驗時,試驗電壓可分 46階段均勻升壓，

24、每階段停留1min，并讀取泄漏電流值。測量時應消除雜電流的影響。During testi ng, the test voltage can be divided into 4-6 steps to in crease voltage uniformly, each step lasts 1 min, and read leakage current value. Eliminate the miscellaneous current in flue nee duri ng measuri ng.4）對額定電壓為 0.6/1kV的電纜可用1000V或2500V兆歐表測量導體對地絕緣電阻代 替直流

25、耐壓試驗。0.6/1kV cable, use 1000V or 2500V Megohmmeter to measure the resista nee of con ductor to earth in sulati on resista nee in stead of DC voltage en dura nee test.5）交流單芯電纜的護層絕緣試驗標準，按產品技術條件的規定進行。AC sin gle core cable protect ion layer test sta ndard should be accord ing to tech no logy con diti on

26、.6）電纜主絕緣交流耐壓試驗Cable main in sulation AC voltage en dura nee test試驗電壓：2U0 ;持續時間：60min （U0:電纜額定相電壓）。Test voltage: 2UO, lasting time: 60min （UO: cable rated voltage）7）按產品技術條件的規定決定進行直流耐壓及泄漏電流測量或是進行電纜主絕緣交流 耐壓試驗。Carry out DC voltage en dura nee and leakage curre nt measure or cable main in sulatio n AC vo

27、ltage test accord ing product tech no logy terms and con diti on stipulati on.8）相位檢查 Phase Check電纜接線相序與系統相位一致。Cable connection order is same with system phase4. 交流電機試驗AC Gen erator Test1）測量繞組的絕緣電阻，使用500V兆歐表，常溫下絕緣電阻值不應低于0.5;額定電壓為1kV及以上，在運行溫度時的絕緣電阻值定子繞組不低于每千伏 1，轉子繞組不應低于每千伏 0.5。Measure wi nding in sula

28、ti on resista nee, use 500v Megohmmeter, in sulati on resista nee valueshall not less than 0.5under normal temperature. Rated voltage is above 1kV,in sulati on resista nee value stator winding is not less tha n 1 /kV un der operati on temperature, stator winding resista nee shall not be less tha n 0

29、.5 /Kv.2）100kW以上的電動機各相繞組直流電阻值相互差別不應超過其最小值的2%,中性點未引出的電動機可測量線間直流電阻，其相互差別不應超過最小值的1%。測量時應記錄環境溫度，以便與出廠試驗值相比較。Above 100kW motor, each winding DC resista nee value differe nee shall be not exceed 2% of the mi nimum, without output n eutral point of the motor, measure the DC resista nee betwee n the lines,

30、their mutual differences should not exeeed 1% of the minimum. Reeord the ambient temperature whe n measuri ng in order to eompare with faetory experime ntal data.不平衡率三相實測最大值最小值三相最小值100%3 phase measured max value-min valueUn bala need value=x100%3phase min3）檢查定子繞組的極性及其連接應正確。中性點未引出者可不檢查極性。Cheek the po

31、larity of the stator windings and conn eeti ons. There can be no eheek ing if the output n eutral point is not available.4）對于備用發電機的試驗，依據制造廠提供的試驗項目及標準進行試驗。Test for Stan dby gen erators, accord ing to the test item and sta ndards provided manu faeturer.5. 繼電器調試 Relay Commissio ning1）調試前，應保證繼電器對試驗電源的要求

32、。電源的波形應為正弦波，諧波分量不超過基波的5%。試驗電源的頻率應為50Hz。當試驗電源頻率對繼電器影響較大時應考慮頻率的正、負偏差對試驗數據的影響，應對試驗數據進行修正。當使用直流電 源試驗時，電源的波紋系數要小。一般情況下，波紋系數K 1%。Before commissioning, ensure relay meets test power requirements. Power should be sinu soidal wave form, the fun dame ntal wave does not exeeed 5% of harm onic wave. The freque

33、ncy of test power should be 50 Hz. When the test freque ncy of power have great in flue nee on relays, positive and n egative deviati on of the test data should be eon sidered, and ame nd test data. When using DC power for test, the corrugated eoeffieie nt is smaller. gen erally, corrugated eoeffiei

34、e nt K 1%.2）使用標準儀表的精度不低于0.5級。Using sta ndard in strume nt preeisi on is not lower tha n 0.53) 使用專用儀器進行調試時，專用儀器上的電表精度不低于0.5 級。Using specialized instrument for commissioning, the instrument ammeter accuracy is not lessthan 0.5.4) 繼電器外殼應清潔無灰塵。外殼、玻璃應完整，嵌接要良好。外殼與底座結合應緊 密牢固，防塵密封應良好，安裝端正。繼電器端子接線應牢固可靠。Relay

35、 shell should be clean. Shell, glass should be complete, embedded is good. Shell should be closely combined with the base, dust-protection seal should be good, correct installation. Relay terminal block should be solid and reliable.5) 繼電器內部應清潔、接線牢固、各部件完好，動作靈活、可靠。The relay inner part shall be clean,

36、connection solid, all part is perfect, flexible and liable6) 繼電器的接點檢查： 應保證接點接觸良好、 無抖動、 粘住或出現火花等異常現象， 并 有足夠的壓力。Relay contact point inspection: ensure contact point is good, jitter-free, no stick and sparkabnormal phenomenon, and sufficient pressure.7) 電磁式繼電器其動作值應測量繼電器的沖擊動作值。然后平穩下降測量繼電器的返 回值。 對于欠量動作的繼

37、電器應將繼電器升到額定值， 然后平穩下降至動作值。 電子 組合式繼電器按制造廠商提供的技術資料中要求進行調試。 Electromagnetic relay operating value shall be the impact operating value. Then steady decline measuring the return value of measuring relays. Increase the value to rated for the unreached, and then decrease steadily to operating value. Commiss

38、ion the electronic combined Relay according to technical information provided by manufacturers.8) 檢查電磁式繼電器的動作、返回值及返回系數應符合產品技術要求。Check Electromagnetic relay operation, return value and return coefficient shall comply with product technology requirement.9) 復核繼電器的動作值。Re-check relay operation value.10)

39、校核、調整熱繼電器的設定值，其動作值應符合被保護設備的容量。Check and commission set value of thermal relay, the operation value shall comply with the capacity of protected equipment.11) 絕緣電阻的測定：額定電壓為 100V 及以上者，使用 1000V 兆歐表；額定電壓為 100V 以下者，使用500V兆歐表。端子對底座和磁導體的絕緣電阻應大于50MQ。各線圈對觸點及各觸點間的絕緣電阻應大于50MQ。各線圈間的絕緣電阻應大于10MQ。由電子元、器件組成的綜合繼電器不進行

40、絕緣電阻的測定。Insulation Resistance meauring: rated voltage of 100 V and above, use of 1000 V Megohmmeter; rated voltage below 100 V, use 500 V Megohmmeter. The loop contact pointand each con tact point in sulati on resista nee should be more tha n 50MQ . The coil and con tactson the con tacts betwee n th

41、e in sulati on resista nee should be more tha n 50twee n the coil MQ . Beinsulation resistance should be greater than 10 MQ .No measure to insulation resistancecomprehensive relay composed of electronic device.1.112) 電磁式繼電器進行沖擊試驗： 電壓型繼電器其沖擊電壓應為該繼電器額定電壓的倍；電流型繼電器其沖擊電流應為保護安裝處最大故障電流。沖擊試驗時，接點不 應產生振動和鳥啄現象

42、。Impact test to electromagnetic relay: the impact voltage of voltage relay s voltage is 1.1 times of its rated voltage, impact current of current relays should be the Max fault current of the protection installed place. During impact test, no vibration and bird pecking phenomenon at contact point.13

43、) 主變壓器保護裝置、測控裝置等各種類型的自動保護裝置的調試方法和調試接線， 按廠商提供的產品技術資料進行調試。Main transformer protective device, detective device etc, all self-protective device commissioning method and commissioning contact shall comply with technology information provided by manufacturer.14) 對多功能綜合保護繼電器的數碼顯示部分應完好，刻度清晰、準確。Multi-functi

44、onal comprehensive protective relay digital display part shall be perfect, Calibration clear and accurate.15) 按產品的技術性能，輸入相應的參數值，檢驗其功能是否符合產品的技術標準。Input parameter values according to product technology performance, check if the functions comply with technology standard.16) 按設計的整定值，檢驗繼電器實際動作值。Check act

45、ual operation value of the relay according to set value.17) 對過量參數值由低值逐漸升至動作值，欠量參數值由額定值降至動作值。Excessive parameters, increase gradually from low value to operation value, less of parameter values decrease from rated value to operation value.18) 在未采取可靠的措施前，不得觸摸繼電器內部電路板，以免靜電損壞電路板。Before no reliable measu

46、res taken, forbid to touch the internal circuit boards to prevent any damage.6. 傳動試驗 Transmission Test1) 主變壓器進線開關、隔離開關、接地開關分、合閘操作；Main transformer input switch, isolation switch, earthing switch turn on/off operation;2) MCC (電動機控制中心)系統分、合閘操作；MCC system turn on/off operation;3) 變壓器保護等動作跳閘及信號的傳動試驗； Tr

47、ansformer protection trip and signal transmission test;MCC wire cabinet4) MCC (電動機控制中心)饋線柜動作跳閘及信號的傳動試驗； protection trip and signal transmission test;5）備用電源自投的傳動試驗； Spare power independent transmission test;6）測量、計量回路的傳動試驗及其它傳動試驗； Measuring and recording loop transmission test and other transmission t

48、est;9）上述傳動試驗應準確、可靠；二次回路絕緣良好。 Above transmission tests should be accurate and reliable; loop should be well isolated.7. UPS （不間斷電源）調試 UPS Commissioning1）UPS （不間斷電源）裝置主機按制造廠技術資料要求進行調試。The commissioning of UPS mainframe should be according to Manu facturer s technical specification documents.2）UPS （不間斷

49、電源）裝置蓄電池絕緣電阻應符合產品技術條件，并按制造廠技術條件進行充放電；充電電壓應符合產品技術條件。10 小時放電應達到 100%放電率。Storage battery isolation resistance of the UPS should comply with technical specification and should be discharged accordingly; charge voltage should comply with technical specification. 10-hour discharge should reach 100% discha

50、rging rate.8. 電氣受、送電 Electric Apparatus Receiving and Supplying Power1）電氣受、送電，遵循先高壓（電源 ）側后低壓 （負荷 ）側，斷電時，先斷低壓側（負荷）側，后高壓 （電源 ）側。 Receiving and supplying power should be from high voltage side and then lower side; breaking power should be from lower voltage side and then higher.2）為保證安全在變壓器受電前將盤柜內所有開關置于

51、斷開位置All the switchesshould be kept Off before receiving power in order to guarantee the safety.3）在額定電壓下對變壓器沖擊試驗 5 次，每次間隔時間為 5min ，無異?，F(xiàn)象 Carry out impacting test 5 times every 5 min under rating voltage, there should be no abnormal situations.4）兩段受電后，在母聯柜母聯開關一、二次核相。 After second phase receiving, check busbar switch phase.5）進行并列運行及進線柜、母聯柜聯鎖試驗Carry out shun