液體滲透探傷報告

1、液體滲透探傷報告LIQUID PENETRANT EXAMINATION REPORT報告號Report No.委托號WPAR- Entrust No.第彳頁共彳頁r11Pageof產品名稱角接試件Name of productP,FW產品編號Product No.類另U/Type訂單號/Order No. 圖號 /DWG. No./檢測部位焊縫+熱影響區+相鄰母材Testing Pos.WM+HAZ+nPM委托單位Customer材 質6082T6Material規格Ske350X150(2.5+2.5)mm數量1Quantity檢驗技術說明 /Testing technical instr

2、uction滲透劑種類Type of penetration標準G型Standard G檢測方法Testing methodn E d坡口形式Groove type/焊接方法Welding processmTIG/141表面狀態Surface preparation兇鏟磨噴砂機加工Grinding sand blasting Machining熱處理狀態Heat-treatment熱處理前熱處理后before heat-treatment after heat-treatment滲透劑PenetrantMR-68乳化劑Emulsion/清洗劑RinseMR-79顯像劑DeveloperMR-7

3、0滲透劑施加萬法Method for penetrant噴 刷 浸 澆paint brush immer. water滲透時間Penetration time 10min乳化劑施加方法Method for emulsion噴 刷 浸 澆paint brush immer. water乳化時間Emulsification time/min顯像劑施加方法Method for developer噴 刷 浸 澆paint brush immer. water顯像時間Development time不少于10分鐘Equal or more than 10 minutes工件溫度Temp. of test

4、ing parts20C對比試塊類型Parallel sample type兇試塊1試塊2Comparator test block 1 Comparator test bl檢驗技術要求和結果 /Testing technical requirement and Testing results檢驗評定標準及級別Inspection evaluation standard aEN 571-1nd class EN 1289 2X檢測工藝編號Test procedure No./返修狀況Repair status未修一修二修No rep.1rep.2rep.檢驗比例Testing ratio100

5、 %需記錄的顯示Recorded display有，見草圖無Yes, refer sketchNo結論Conclusion合格不合格AcceptableNot acceptable檢測部位缺陷情況 /Defects at the test position序號No.焊縫(工件) 部位編號Welds(Parts)Pos. No.缺陷 編號DefectNo.缺陷 類型DefectType缺陷痕跡尺寸Defect Tracesize (mm)缺陷處理方式Repair of the defects缺陷處理結果Status of the repaired defects最終 級另uFinalClass打磨Grinding補焊Repair welding無缺陷Nodefect有缺陷Defect缺陷類型Defect Type磁痕尺寸Mag.Tra size(mm)J7備 注：/Remarks：探傷員/Tested by審核/Verified by日期/Date審定及檢驗章 /Approved by and Seal of test1.上述檢測報告無檢測單位章、檢測、審核、批準人簽字蓋章無效4.上述檢測報告的結果僅指來樣和現場當時所檢