手機結構2D圖技術標注參考規范

1、文件類型文件編號版本結構2D NOTE頁數有效期限保密級管理辦法1.028/282005/07/012008/07/01保密德信無限通訊科技(上海)有限公司TechFaith Wireless Communication Technology (Shanghai) Co.,LTD.結構2D圖 技術標注參考規范文件編號 ：QC1001保密等級 ：保密文件類型 ：管理辦法有效期 ：3年頁數 ：1/28版本 : 1.0編制日期 ：2004/05/24開始執行日：2005/07/01NO編制/變更日期變更理由變更內容版本編制/修改人批準12004/05/24新編0.1沈林王迅22006/01/04修改

2、將2D標準樣板圖中技術標注更新到本文件中1.0蔣偉鵬丁勇目錄索引01. Latch02. Antenna03.1 PCBA limited drawing03.2 PCBA outline drawing04. Battery 05.1 Lens(注塑)05.2 Lens(CNC)06.1 Audio cover06.2 RF_switch_cover07.1 Shielding cover07.2 Shielding frame 07.3 Spring08. Metal dome09. Stop TPU10. Light guide 11. Fpcba12.1 金屬裝飾件12.2 Logo1

3、2.3 Plating plastic12.4 Electroform13.1 雙面膠13.2 泡棉13.3 銅箔13.4 絕緣片14.1 Keypad asm14.2 keypad rubber14.3 Keypad 電鍍鍵帽14.4 Keypad 數字鍵15.1 外觀漆噴漆圖15.2 導電漆噴漆圖16. Housing part drawing17. Housing Assembly18. Explode01. Latch技術要求（Notes）:1. 材料：POM Dupont500, 用100%原材料; Material: POM Dupont500,use 100% raw mater

4、ial .2. 尺寸: 圖面尺寸用于檢驗零件外形、功能和裝配; 未注圓角R0.05,未注脫模斜度1度, 未注尺寸依照Pro/e 3D Data; 標有環形圈:每批次出貨均需檢查；Qualify時需要做CP/CPK; Dimension: Specified dimensions in the drawing are used to check outside shape, function and assembly; Unspecified round: R0.05mm; Unspecified draft angle: 1%d; Unspecified dimensions refer to

5、 Pro/e 3D model data; Specified dimensions with marked ring are critical dimensions, need to be checked every shipment, and must do CP/CPK check in the Qualification stage.3. 公差：未注公差依照?qǐng)D面公差表; Tolerance: Unspecified tolerance should comply with tolerance table in the drawing;4. 外觀：成品清潔、無雜質、無劃傷、縮水及其它瑕疵

6、; 飛邊及分型線段差0.03mm;頂桿痕0.05mm;澆口凸出0.10mm; 穴號應刻在模具上，標志不得高于表面; 外觀皮紋: VDI 24; Appearance：Product should be tidy and purity, no nick, no shrinkage and other blemish; Galling should be less than 0.03mm; Ejector rod mark should be less than 0.05mm; gate trim should be less than 0.10mm; Cavity number shall be

7、 located low on the surface. Appearance require:VDI 24.5. 檢測須滿足德信質量標準:部品檢驗標準_注塑件_x.x_xxxxxx Product should be satisfied with quality standard of Techfaith Wireless:部品檢驗標準_注塑件_x.x_xxxxxx02. Antenna1.材料：見圖,用100%原材料;1.Material: Refer to the drawing table, in original color and with 100% raw material.2.

8、尺寸：圖面尺寸用于檢驗零件外形、功能和裝配; 未注圓角R0.05,未注脫模斜度1度, 未注尺寸依照Pro/e 3D Data; 標有環形圈的是重點尺寸,每批次出貨均需檢查,Qualify時需要做CP/CPK；2.Dimension: Specified dimensions in the drawing are used to check outside shape, function and assembly;返回索引目錄 Unspecified round: R0.05mm; Unspecified draft angle: 1; Unspecified dimensions refer

9、to Pro/e 3D model data; Specified dimensions with marked ring are critical dimensions, need to be checked every shipment, and must do CP/CPK check in the Qualification stage.3.公差：未注公差依照?qǐng)D面公差表;3. Tolerance: Unspecified tolerance should comply with tolerance table in the drawing;4.外觀: 成品清潔、無雜質、無劃傷、縮水及其

10、它瑕疵;飛邊及分型線段差0.03mm,頂桿痕0.05mm;澆口凸出0.05mm;穴號應刻在模具上，標志不得高于表面;外觀皮紋：拋光4.Appearance：Product should be tidy and purity, no nick, no shrinkage and other blemish;Galling shall be less than 0.03mm, ejector rod mark shall be less than 0.05mm, gate trim shall be less than 0.05mm.Cavity number shall be located l

11、ow on the surface. Surface shall be smooth.5.電氣性能依照規格書：violet1-Antenna SPEA-05-02-18.pdf。5.Electro performance shall be according to spec: violet1-Antenna SPEA-05-02-18.pdf6.噴涂: 范圍:見噴漆圖； 油漆顏色及色差:E1； 噴漆厚度: 底漆8-10 um；UV10-12 um； 油漆硬度:2H，500gf； 油漆耐磨:RCA 300 cycles； 油漆附著力:百格實驗，脫落面積3%.6.Coating:Painting

12、range:refer to the painting drawing.Paint color and aberration: E1 Paint thickness:BC 8-10 um；UV10-12 um；Paint hardness test: 2H，500gfPaint abrasion test: RCA 300 cyclesPaint peeling test: area of peeling3%.7.包裝與運輸:零件獨立包裝,放入托盤對應的凹穴,托盤層堆放入紙箱;7.Package and Transport: Product should be packaged indepen

13、dent, and lay in tray, finally put the trays in the paper box;8.檢測須滿足德信質量標準： 部品檢驗標準-天線VX.X8.Product should be satisfied with quality standard of Techfaith Wireless: 部品檢驗標準-天線VX.X.03.1 PCBA Limited drawing 1. 區域限高為電子元件限高，不包括SHIELDING和圖中已經標出的結構電子件。返回索引目錄 (Shielding) -指可以放置屏蔽罩區域。放置屏蔽罩時，罩內元件限高； (No Shie

14、lding)-指可以放置屏蔽罩區域。不放置屏蔽罩時元件限高； Limiting Height for shielding area is only for electronic componets inside , not including shielding and the mechanical electronic components been included in this drawing; (Shielding) -Shielding is allowable is this area.The limiting height for the components with shi

15、elding； (No Shielding)-Shielding is allowable is this area.The limiting height for the components without shielding；2. 器件準確位置以文件中的 直角頂點為準;IO ConnAudio jack etc.位置以PCB定位孔為準; The vertex of the right-angle indicate the center of the componets . Location of IO Conn /Audio jack etc. base on the PCB orien

16、tation holes;3. 器件布置時元件PAD 不能超出限高區域邊界線; Componentspad should be located inside the the outline of limited area;4. 螺絲孔做(不做)銅化處理。 Screw hole is PTH（NPTH） type.03.2 PCBA outline drawing1. 圖面尺寸用于檢驗PCB外形、功能和裝配; Specified dimensions in the drawing are used to check PCB outside shape, function and assembly

17、;2. 重點尺寸:標有環形圈，每批次出貨均需檢查；Qualify時需要做CP/CPK； Specified dimensions with marked ring are critical dimensions, need to be checked every shipment; and must do CP/CPK check in the Qualification stage;3. 未注公差參照?qǐng)D面公差表; Unspecified tolerance should comply with tolerance table in the drawing;4. 產品檢驗標準：PCB來料外觀檢

18、驗標準1.0_050412； Product should be satisfied with quality standard of Techfaith Wireless: PCB來料外觀檢驗標準1.0_050412；5.包裝： 產品按一定數量密封包裝，需防污防潮。 Package of product should be quantitative, sealed, dustless and dampproof .04. BATTERY1.電池后蓋與電芯之間用雙面膠粘貼;Using double adhesive between battery rear cover and cell;2.電

19、池前后蓋超焊后，前后殼配合周邊嚴禁溢料;返回索引目錄 焊接牢固可靠，不許有虛焊，封裝后厚度方向的變形量不超過0.15mm;After ultrasonic welt,burr is forbidden around battery;The welding should be fastness and dependable, no false-welding,deformation in heignt should be less than 0.15mm.3.尺寸: 圖面尺寸用于檢驗零件外形、功能和裝配; 標有環形圈的是重點尺寸,每批次出貨均需檢查；Qualify時需要做CP/CPK;Dimen

20、sion: Specified dimensions in the drawing are used to check outside shape, function and assembly; Specified dimensions with marked ring are critical dimensions, need to be checked every shipment, and must do CP/CPK check in the Qualification stage.4.BATT_CONN需鍍金，鍍層厚度不小于0.5um; Batt_conn must be gilt,

21、 coating thickness must be no less than 0.5um 鹽霧試驗：35，5% 氯化鈉溶液，48小時后無腐蝕; Salt fog test: In35C 48h 5% NaCl salt fog concentration, it can not be rusty after 48hs 跌落試驗：1.5米高度，6面3棱1角分別跌落，水泥地面， 兩輪共20次跌落，電池功能正常，外觀無明顯損傷;1.5m drop test: 6 faces (Left Back Right Bottom Top Front) , 3 edges 1corner ,1 drop p

22、er face,edge ;corner,2cycles, battery function must be normal , have no obvious damages in apperance.5.電氣性能依照文件：Li+電池SPECVX.X; Electric function refer to: Li+BATTERY SPECVX.X6.包裝與運輸：電池用塑料袋和紙盒獨立包裝。 Package and Transport: Product should be packaged independent, and lay in tray, finally put the trays i

23、n the paper box;7.檢測須滿足德信質量標準： Product should be satisfied with quality standard of Techfaith Wireless: 部品檢驗標準_注塑件V X.X ;GB_T18287_2000蜂窩電話用鋰離子電池總規范05.1. LENS(注塑) 技術要求：1. 圖面尺寸用于檢驗零件外形、功能和裝配， 未注尺寸請參考3D Pro/Engineer 零件圖。 Specified dimensions in the drawing are used to check outside shape, function and

24、 assembly;Unspecified dimensions refer to Pro/e 3D model data;2. 重點尺寸:標有環形圈。每批次出貨均需檢查；Qualify時需要做CP/CPK；Specified dimensions with marked ring are critical dimensions, need to be checked every shipment, and must do CP/CPK check in the Qualification stage.返回索引目錄3.未注公差參照?qǐng)D面公差表;Unspecified dimension tole

25、rance should comply with the general tolerance table in drawing.4. 材料： 材料采用 PMMA 三菱VRL-40 ,顏色為無色透明,注塑時須采用100%原材料。 Material: PMMA VRL-40(Mutusubishi), transparent color and with 100% virgin material.5. 外觀： Appearance: 1)所有圓角半徑和脫模斜度按照Pro/e 3D Data; Round and draft should comply with Pro/e 3D Data 2)未注

26、脫模斜度為1度,未注圓角為R0.2; Draft angle should be less than 1%d, unless otherwise specified. Unspecified round: R0.2mm; 3)澆口切割后,殘留0.05mm. GATE PROJECTION SHALL NOT EXCEED 0.05MM BEYOND THE PART SURFACE UNLESS OTHERWISE SPECIFIED. 4)LENS透明部分要求在黑色背景檢查,要求表面無變形,無黑白點及其它瑕疵; LENS transparent area should be checked

27、in black background, no flaws. 5)印刷部分要求色彩均勻、無劃傷、黑白點、瑕疵; Print area shoudle be uniformity, no nick , no flaws. 6)印刷字體及顏色請參照右下腳表; Artwork should be in the file index in the right-down corner.6、透光率91%以上; Transparency ratio: 91%.7、正面噴涂UV,UV漆表面硬度3H,1kgf Hardness of surface should be more than 3H,1kgf aft

28、er UV coating.8. 耐磨:RCA 300 cycles； Wearable : RCA 300 cycles；9. 附著力:百格實驗，脫落面積3%，并沒有整格脫落； The ply adhesion of printing ink : 3% ,no hwale pane desquamate.10. 模具要求： Tooling requirement: 產品區域無頂桿痕. No mark of injection pin. 澆口位置需與設計者商定； Locations of gate should be determined by arrangements. 外觀為鏡面; Tex

29、ture: polished to mirror .11、環境要求：產品應在十萬級以上工作室清潔、包裝. Environment requirement: Product should be made and packaged in clean condition.12. 包裝與運輸： 零件需獨立包裝，產品兩表面需有靜電保護膜， 放入托盤對應的凹穴，托盤層堆放入紙箱。 Package and Transport: Product should be packaged independent, and lay in tray, 返回索引目錄 finally put the trays in th

30、e paper box; surface of product should be protected with static film. 13、檢測須滿足德信質量標準： Product should be satisfied with quality standard of Techfaith Wireless: 1)部品檢驗標準-Lens_VX.X_XXXXX.pdf 2)手機綜合檢驗標準_VX.X_XXXXXX.pdf 05.2. LENS(CNC)1. 圖面尺寸用于檢驗零件外形、功能和裝配， 未注尺寸請參考3D Pro/Engineer 零件圖。 Specified dimension

31、s in the drawing are used to check outside shape, function and assembly; Unspecified dimensions refer to Pro/e 3D model data; 2. 重點尺寸:標有環形圈。每批次出貨均需檢查；Qualify時需要做CP/CPK； Specified dimensions with marked ring are critical dimensions, need to be checked every shipment, and must do CP/CPK check in the Q

32、ualification stage.3.未注公差參照?qǐng)D面公差表; Unspecified dimension tolerance should comply with the general tolerance table in drawing.4. 材料：材料采用 PMMA 三菱NR200板材 ,顏色為無色透明。 Material: PMMA NR200(Mutusubishi), transparent .5. 外觀： Appearance: 1)LENS透明部分要求在黑色背景檢查,要求表面無變形,無黑白點及其它瑕疵; LENS transparent area should be ch

33、ecked in black background, no flaws. 2)印刷部分要求色彩均勻、無劃傷、黑白點、瑕疵; Print area shoudle be uniformity, no nick , no flaws. 3)印刷字體及顏色請參照右下腳表; Artwork should be in the file index in the right-down corner.6. 透光率93%以上. Transparency ratio: 93% 7、表面硬度5H,1Kgf; Hardness of surface should be more than 5H,1kgf.8. 耐磨

34、:RCA 300 cycles； Wearable : RCA 300 cycles；9. 附著力:百格實驗，脫落面積3%，并沒有整格脫落; The ply adhesion of printing ink : 3% ,no hwale pane desquamate.10、環境要求：產品應在十萬級以上工作室清潔、包裝. Environment requirement: Product should be made and packaged in clean condition.11. 包裝與運輸：返回索引目錄 零件需獨立包裝，產品兩表面需有靜電保護膜， 放入托盤對應的凹穴，托盤層堆放入紙箱。

35、 Package and Transport: Product should be packaged independent, and lay in tray, finally put the trays in the paper box; 12、檢測須滿足德信質量標準： Product should be satisfied with quality standard of Techfaith Wireless: 1)部品檢驗標準-Lens_VX.X_XXXXX.pdf 2)手機綜合檢驗標準_VX.X_XXXXXX.pdf06. Audio_cover & RF_switch_cover06

36、.1. Audio_cover1.材料：SANTOPRENE 201-64，硬度：643SHA，用100%原材料; Material: SANTOPRENE 201-64, hardness: 643 SHA,with 100% raw material .2.尺寸: 圖面尺寸用于檢驗零件外形、功能和裝配; 未注尺寸依照Pro/e 3D Data，未注圓角R0.05,未注脫模斜度1度; 標有環形圈的是重點尺寸,每批次出貨均需檢查,Qualify時需要做CP/CPK;Dimension: Specified dimensions in the drawing are used to check

37、outside shape, function and assembly; Unspecified round: R0.1mm; Unspecified draft angle: 1degree; Unspecified dimensions refer to Pro/e 3D model data; Specified dimensions with marked ring are critical dimensions, need to be checked every shipment, and must do CP/CPK check in the qualification stag

38、e.3.公差：未注公差依照?qǐng)D面公差表; Tolerance:Unspecified tolerance should comply with tolerance table in the drawing;4.外觀：邊及分型線段差0.05mm; 成品清潔、無雜質、無劃傷、縮水及其它瑕疵; 頂桿痕低于表面00.05mm;澆口凸出0.05mm; 穴號應刻在模具上，標志不得高于表面; 外觀皮紋: VDI 21; Appearance:The burr , step of part-line : 0.05mm Product should be tidy and purity, no nick, no

39、shrinkage and other blemish; Mark of ejection pin should be lower 0.05mm than product surface; Height of injection gate remained in the product should be lower 0.05mm; Cavity number should be carved on cavity or core,Its mark no higher than product surface. Surface texture: VDI 21;返回索引目錄5. 包裝與運輸：采用夾

40、鏈袋包裝，注明袋內數量; Package and Transport: packaged by chain bags,and label the quantity .06.2. RF_switch_cover1. 圖面尺寸用于檢驗零件外形、功能和裝配，未注尺寸請參考3D Pro/Engineer 零件圖。 Dimension: Specified dimensions in the drawing are used to check outside shape, function and assembly; Unspecified dimensions refer to Pro/e 3D mo

41、del data;2. 材料:采用silicon rubber;硬度要求：6070SH A Material: silicon rubber;Hardness：6070SH A3. 公差/外觀：未注公差參照?qǐng)D面公差表； Tolerance: Unspecified tolerance should comply with tolerance table in the drawing; 飛邊及分型線段差不得大于0.1mm， 所有圓角半徑和脫模斜度按照Pro/e 3D Data； Step of parting_line should be less than 0.1mm unless other

42、wise specified， All Radius of corner and draft angle should be Pro/e 3D Data； 完成產品應清潔、無雜質，零件外表面應光滑,無飛邊、無劃傷、縮水及其它瑕疵； Product should be tidy and purity, suface shoud be smooth, no nick, no shrinkage and other blemish; 重點尺寸:標有環形圈; Specified dimensions with marked ring are critical dimensions 成型顏色要求：采用P

43、ANTONE cool gray 4c Color of molding:use PANTONE cool gray 4c4. 包裝與運輸：采用夾鏈袋包裝，注明袋內數量。 Package and Transport: package by chain bags and lable the quantity. 07. Shielding、spring07.1. Shielding_cover1.材料: SUS304(不銹鋼),T=0.20mm; 1.Material: SUS304(stainless steel), T=0.20mm,; 2.尺寸:圖面尺寸用于檢驗零件外形、功能和裝配;未注尺寸

44、依照Pro/e 3D Data; 標有環形圈的是重點尺寸,每批次出貨均需檢查,Qualify時需要做CP/CPK;2.Dimension: specified dimension in the drawing shall be used to check outside shape,function and assembly; unspecified dimensions refer to Pro/e 3D model data;返回索引目錄 Specified dimensions with marked ring are critical dimensions, need to be ch

45、ecked every shipment, and must do CP/CPK check in the Qualification stage.3.公差:未注公差依照?qǐng)D面公差表;3.tolerance: Unspecified tolerance should comply with tolerance table in the drawing;4.外觀:毛刺0.05mm, 為沖切毛刺方向，成品清潔、無雜質、無劃傷及其它瑕疵; 無凹陷，凸起，平面度0.1mm;4.Appearance: stamping burr shall be less than 0.05mm, the symbol

46、indicates burr direction; finished product be tidy, no purity, no scratch, no sink depressions, no heave and other defects. the planeness shall be less than 0.1mm;5.包裝與運輸：零件獨立包裝，放入托盤對應的凹穴，托盤層堆進紙箱。5.package and transportation: Product should be packaged independent, and lay in tray, finally put the t

47、rays in the paper box;6.檢測須滿足德信質量標準：金屬件檢測標準VX.X6.Product should be satisfied with quality standard of Techfaith Wireless: 金屬件檢測標準VX.X07.2. Shielding_frame1.材料:C7521R(鎳白銅),T=0.20mm,保證良好焊接性能，任何兩點間電阻不大于0.2歐姆;1.Material: C7521(cupronickel),the material have the well performance of welding , any two poin

48、ts resistance shall be less than 0.2;2.尺寸:圖面尺寸用于檢驗零件外形、功能和裝配;未注尺寸依照Pro/e 3D Data;標有環形圈的是重點尺寸,每批次出貨均需檢查,Qualify時需要做CP/CPK;2.Dimension: specified dimension in the drawing shall be used to check outside shape,function and assembly; unspecified dimensions refer to Pro/e 3D model data; Specified dimensio

49、ns with marked ring are critical dimensions, need to be checked every shipment, and must do CP/CPK check in the Qualification stage.3.公差:未注公差依照?qǐng)D面公差表;3.tolerance: Unspecified tolerance should comply with tolerance table in the drawing;4.外觀:毛刺0.05mm, 為沖切毛刺方向，成品清潔、無雜質、無劃傷及其它瑕疵; 無凹陷，凸起，平面度0.1mm;4.Appear

50、ance: stamping burr shall be less than 0.05mm, the symbol indicates burr direction; finished product be tidy, no purity, no scratch, no sink depressions, no heave and other defects. the planeness shall be less than 0.1mm;5.包裝與運輸： 把屏蔽罩同向放入SMT編帶包裝，運輸途中避免受壓變形。5.package and transportation: put shieling

51、in SMT band ,Dont change the figure with press返回索引目錄 in transport.6.檢測須滿足德信質量標準：金屬件檢測標準VX.X6.Product should be satisfied with quality standard of Techfaith Wireless: 金屬件檢測標準VX.X07.3. Spring技術要求:1.彈簧預壓縮1.50mm，最大壓縮3.30mm；1.Pre-compresss spring is 1.5mm, the largest compress is 3.3mm.2.彈簧參數：見參數表；2.para

52、meter of spring: see the table of parameter;3.F/S圖：見圖；3.The drawing of F/S: see this F/S drawing; 4.材料：SUS304；4.Material:SUS304(stainless steel); 5.包裝與運輸：采用自封袋包裝，標明數量。5.package and transportation: Product should be lay in self-given sack, and mark the quantity;6.檢測須滿足德信質量標準：金屬件檢測標準VX.X6.Product should be satisfied with quality standard of Techfaith Wireless: 金屬件檢測標準VX.X08. Metal_dome1、圖面尺寸用于檢驗零件外形