VPOSAFE32047可回收瓶裝線安全防護標準SafetyCommissioningToolRGBLine

1、Annex 7. VPO.SAFE.3.2.04.7. Safety Safety Commissioning Tool Returnable Glass Bottle Line附件7.VPO.SAFE.3.2.04.7 安全新包裝線安全防護標準-可回收瓶裝線Version 2第二版2012-05-10Purpose目的4Safety Commissioning Tool for a new RGB (Returnable Glass Bottle) Line. 用于規范新瓶裝線（可回收瓶）投產時安全防護標準。用于規范新瓶裝線（可回收瓶）投產時安全防護標準。4Tool development

2、標準的建立標準的建立: Modular built. 分類。Containing basic safety AB InBev standards for each module. 符合百威英博的基本安全標準。Easy and user-friendly standardised Audit checklist to be used during commissioning of new Bottle lines by ES or Project Department, applicable for all modules. 在新瓶裝線投產期間，ES及項目部門將使用此簡單易懂、容易掌握的標準對設

3、備安全進行檢查。Modules & Content分類和目錄4FLT Loading/Un-loading point叉車裝卸點4De-palletiser/Palletiser卸垛機/碼垛機4Pallet Stacker/De-stacker托盤碼垛機/卸垛機4De-crater/Crater卸箱機/裝箱機4Carton former成型機4Carton sealer封箱機4Crate Turner翻箱機4Crate Washer洗箱機4Crate Buffer塑箱提升機4Bottle Washer洗瓶機4Filler裝酒機4Tunnel Pasteuriser 隧道式巴式殺菌機4L

4、abeler貼標機4EBI空瓶檢驗機4Top Sawer割紙箱機4Conveyors輸送帶4General Requirements一般要求4Acceptance Checklist驗收檢查清單FLT Loading/Un-loading point 叉車裝卸點(1)Attention points關注關注點點:1.Proper protection preventing damages at conveyor from FLT (metal vertical plate or floor plate with FLT wheel stops) 采取適當?shù)谋Ｗo措施，防止叉車對輸送帶造成損壞（使

5、用金屬材質的垂直擋板或在地面上設置叉車輪阻）2. Ultrasonic sensor to stop the conveyor when FLT approaches or pedestrians approach 設置超聲波傳感器，當叉車或行人靠近時，停止輸送帶運行。3. Backplate preventing falling goods during (un-)loading. Avoid gaps between plate and conveyor! 裝裝/卸載期間，背面設置防護板可防止貨物墜落。防護板緊貼輸送帶，卸載期間，背面設置防護板可防止貨物墜落。防護板緊貼輸送帶，注意防護板緊

6、貼輸送帶，沒有空隙。注意防護板緊貼輸送帶，沒有空隙。123FLT Loading/Un-loading point 叉車裝卸點(2)Attention points關注關注點點:4. Chain conveyors: sprocket wheels to be properly guarded avoiding nip points鏈鏈式輸送帶：鏈輪要防護得當，避免式輸送帶：鏈輪要防護得當，避免出現嚙合點出現嚙合點44FLT Loading/Un-loading point 叉車裝卸點(3)Attention points關注關注點點:5. Roller conveyors: sprocket

7、 wheels at the end of the conveyor to be properly guarded avoiding nip points滾筒式輸送帶：輸送帶末端的鏈輪要保護得當，避免出現嚙合點。避免出現嚙合點。6. Motor cover plates to be fitted against conveyor frame avoiding finger access to chains。在輸送帶邊部安裝電機防護蓋板，在輸送帶邊部安裝電機防護蓋板，避免手指碰到鏈條。避免手指碰到鏈條。566Modules & Content分類和目錄4FLT Loading/Un-lo

8、ading point叉車裝卸點4De-palletiser/Palletiser卸垛機/碼垛機4Pallet Stacker/De-stacker托盤碼垛機/卸垛機4De-crater/Crater卸箱機/裝箱機4Carton former成型機4Carton sealer封箱機4Crate Turner翻箱機4Crate Washer洗箱機4Crate Buffer塑箱提升機4Bottle Washer洗瓶機4Filler裝酒機4Tunnel Pasteuriser 隧道式巴式殺菌機4Labeler貼標機4EBI空瓶檢驗機4Top Saw割紙箱機4Conveyors輸送帶4General

9、Requirements一般要求4Acceptance Checklist驗收檢查清單De-palletiser/Palletiser 卸垛機/碼垛機(1)2mAttention points關注關注點點:1.Access is deterred by fixed fencing of minimum 2m high 至少設置2m高的固定柵欄進行隔離，防止人員進入，固定柵欄完整無空隙，不能讓人進入；2. Entrance and exit points of Unit Loads (pallet + goods) are safeguarded with light barriers with

10、 muting system. (Minimum Safety Category 3) 在成垛貨物（托盤+貨物）的進出口，設置屏蔽系統進行防護（安全類別至少為（安全類別至少為3類）類）- The fixed fences do not allow entrance between the light barrier and the fence 柵欄緊貼光柵欄緊貼光幕幕，光，光幕幕與柵欄之間不能留有空隙讓人進入。與柵欄之間不能留有空隙讓人進入。- The position of the light barrier does not allow entrance between the light

11、 barrier and the conveyor 光幕光幕緊貼輸送帶，輸送帶和緊貼輸送帶，輸送帶和光幕光幕之間不能留有空隙讓人進入。之間不能留有空隙讓人進入。12De-palletiser/Palletiser (2)Attention points:3. Entrance and exit points of empty pallets are safeguarded with fixed fences only allowing a letter box type opening to let an empty pallet pass through.空空托盤進出點的開口應設置足夠小，運

12、用郵筒原則托盤進出點的開口應設置足夠小，運用郵筒原則只允許托盤出入。只允許托盤出入。4. Entrance and exit points of crates are safeguarded with fixed fences only allowing a letter box typeopening to let a crate pass through. The height of the opening shall never be more than 50cm.塑箱及成品進出點的開口應設置足夠小，運用郵筒原則塑箱及成品進出點的開口應設置足夠小，運用郵筒原則只允許塑箱或成品出入，高度不

13、得大于只允許塑箱或成品出入，高度不得大于50cm34 Double key system (fortress type) with both a mechanical and electronical lock （See more in next slide） 同時帶有機械鎖和電子鎖的雙鎖系統(fortress type，見下頁圖片)- Single key system (with master key on the electrical cabinet or control panel) 單鎖系統（配電柜或控制面板上有主鑰匙）- A reset command must be given

14、before re-start command is accepted 必須先復位才可以重新啟動。必須先復位才可以重新啟動。- Interlocks must be robust and not easy to override 聯鎖裝置必須是堅固耐用并不易失靈聯鎖裝置必須是堅固耐用并不易失靈5555Safe Access to Machines-Key system for palletizer and depalletizer 安全進入機器內部安全進入機器內部-鑰匙系統鑰匙系統-碼垛卸垛機碼垛卸垛機Normal situation機器正常運機器正常運轉狀態轉狀態121Move key 2,

15、 the guarding door can be opened 取下鑰匙取下鑰匙2，可，可打開防護門打開防護門Move Key 1 ,stop the machine 取下鑰匙取下鑰匙1，機器，機器停止停止221Put Key 1 into the protection key 將鑰匙將鑰匙1插入保護插入保護鎖中鎖中De-palletiser/Palletiser 卸垛機/碼垛機 (4)Attention points關關注點注點:6. The machinery shall be equipped with a mechanical blocking device (eventually

16、with electronical sensor) to hold the de-pal/pal in its raised position during maintenance or repair activities.機器應該配有機械的防護裝置（配有電子感應器），保證在維護或維修期間卸垛機/堆垛機處于懸空狀態時不會掉落下來。Different systems may apply可以使用不同的系統:- Manual system (with bar)- Automatic system手動系統（帶有防護桿）自動系統6666De-palletiser/Palletiser 卸垛機/碼垛機 (

17、5)Attention points關注關注點點:7. Turntables will be equipped with a fixed plate leaving a gap of maximum 5mm between the fixed plate and the rotating part. In all other occasions, the turntable shall be safeguarded with fixed fencing and an interlocked access door.轉向器周圍的固定裝置與轉盤的最大距離不超過5mm。在所有其它情況下，轉盤應該通過

18、固定式柵欄和聯鎖通道門進行防護。7Attention points關注關注點點:8. Roller conveyors: infill plates will be installed at operator working positions and at crossing sections.The gap between the infill plates and rollers shall not exceed 5mm.滾滾輪式輸送帶：在操作工工作位置輪式輸送帶：在操作工工作位置及橫跨區域安裝填充板。及橫跨區域安裝填充板。填充板及滾輪之間的間隙不應該超填充板及滾輪之間的間隙不應該超過過5

19、mm。9. Conveyor crossing sections shall be equipped with steps with handrails and interlocked gates stopping the conveyor when crossing, and with a reset button re-starting the conveyor (a new start command is not necessary).輸送帶橫跨區域應該配有臺階及扶手，和有人穿過時可以停止輸送帶運行的聯鎖門以及可以重新啟動輸送帶的復位按扭（不需要再次按下啟動按鈕）889De-palle

20、tiser/Palletiser 卸垛機/碼垛機 (6)Attention points關關注點注點:10. The operating position shall be designed and constructed in such a way to ensure 100% segregation, by physical means, between the operator and any Fork Lift Truck movement and/or any load handled by a Fork Lift Truck.設計操作工工作位置時，應該借助設計操作工工作位置時，應該

21、借助物理手段確保操作工與移動的叉車物理手段確保操作工與移動的叉車、和、和/或通過叉車控制的任何裝載活或通過叉車控制的任何裝載活動動100%隔離隔離。10De-palletiser/Palletiser 卸垛機/碼垛機 (7)Attention points關關注點注點:11. Moving parts of upper part of palletiser totally screened off 頂部的移動部件都已保護起來。如需開頂部的移動部件都已保護起來。如需開門，應設置聯鎖開關門，應設置聯鎖開關11Tunnel guarding隧道式防護Modules & Content分類和目

22、錄4FLT Loading/Un-loading point叉車裝卸點4De-palletiser/Palletiser卸垛機/碼垛機4Pallet Stacker/De-stacker托盤碼垛機/卸垛機4De-crater/Crater卸箱機/裝箱機4Carton former成型機4Carton sealer封箱機4Crate Turner翻箱機4Crate Washer洗箱機4Crate Buffer塑箱提升機4Bottle Washer洗瓶機4Filler裝酒機4Tunnel Pasteuriser 隧道式巴式殺菌機4Labeler貼標機4EBI空瓶檢驗機4Top Saw割紙箱機4Co

23、nveyors輸送帶4General Requirements一般要求4Acceptance Checklist驗收檢查清單Attention points關注關注點點:1. Access is deterred by fixed fencing of minimum 2m high設置至少2m高的固定柵欄進行隔離，防止人員進入；2. Entrance and exit points of empty pallets are safeguarded with fixed fences only allowing a letter boxtype opening to let an empty

24、pallet pass through. 空托盤進出點固定開口應設置足夠小，運用郵筒原則只允許托盤出入。只允許托盤出入。3. Entrance / exit points for FLT are safeguarded with light barriers stopping the stacker/de-stacker andConveyor叉車進出點通過設置光電開關進行防護，叉車在此區域工作時可停止堆垛機/卸垛機和輸送帶的運行。4. Alternatively to point 3, an ultrasonic sensor stopping the stacker/de-stacker

25、and conveyor when FLTapproaches or pedestrians approach might be applied.同第3點類似的防護方法：安裝超聲傳感器，當叉車或路人靠近時同樣也可以停止堆垛機/卸垛機和輸送帶的運行5. Proper protection preventing damages at conveyor from FLT (metal vertical plate or floor plate with FLTwheel stops) 采取適當?shù)谋Ｗo措施，防止叉車對輸送帶造成損壞（使用金屬材質的垂直擋板或在地面上設置叉車輪阻） 6. Maximum

26、stacking height control sensor is mandatory必須安裝最大堆垛高度控制傳感器。1254362mPallet Stacker/De-stacker 托盤托盤碼垛機碼垛機/卸垛機卸垛機Modules & Content分類和目錄4FLT Loading/Un-loading point叉車裝卸點4De-palletiser/Palletiser卸垛機/碼垛機4Pallet Stacker/De-stacker托盤碼垛機/卸垛機4De-crater/Crater卸箱機/裝箱機4Carton former成型機4Carton sealer封箱機4Crat

27、e Turner翻箱機4Crate Washer洗箱機4Crate Buffer塑箱提升機4Bottle Washer洗瓶機4Filler裝酒機4Tunnel Pasteuriser 隧道式巴式殺菌機4Labeler貼標機4EBI空瓶檢驗機4Top Saw割紙箱機4Conveyors輸送帶4General Requirements一般要求4Acceptance Checklist驗收檢查清單De-crater/Crater 卸箱機/裝箱機(1)1334Attention points關注關注點點:1.Access at the frontside is deterred by an inter

28、locked screen. (Minimum Safety Category 3) 機器正面防護門上設置聯鎖開關防止人員進入；(安全類別至少為3類)2. Alternatively to point 1, an open frontside, providing sufficient safety distance and a light barrier . (Minimum Safety Category 3) ,might be applied. 替代第一種方式：正面：需保證安全距離和一個光幕。(安全類別至少為3類)3. Easy access for manual interventi

29、on is made possible by steps 借助臺階能很輕易地接近設備處理故障。4. The screen shall not form any trap hazard for hands or fingers when closed between its lowestposition and the steps當當防護門關閉時，防護門的最低點和臺階之間應沒有空隙，避免對手或手指造成傷害。防護門關閉時，防護門的最低點和臺階之間應沒有空隙，避免對手或手指造成傷害。2De-crater/Crater 卸箱機/裝箱機(2)Attention points關注關注點點:5. Acces

30、s to the machinery shall be provided by interlocked screens. (Minimum Safety Category 3)設置具有聯鎖開關的防護門以進入機器。（安全類別至少為3類）- Interlocks must be robust and not easy to override聯鎖開關應該堅固耐用，且不易失效聯鎖開關應該堅固耐用，且不易失效Different systems may apply可以使用不同的系統:- Manual (depending weight of the screen)手動的（取決于聯鎖防護門的重量）- Ele

31、ctrical (opening can be by push release, closing must be by continuous push command)電動的（通過“推-放”打開，持續的“推”命令關閉）6. A reset command must be given before re-start command is accepted必須先復位才可以重新啟動。必須先復位才可以重新啟動。56De-crater/Crater 卸箱機/裝箱機(3)Attention points關注關注點點:7. Access at the backside is deterred by fixe

32、d fencing or two photocells (40cm,90cm from the conveyor).機器背面應該設置固定欄柵防止人員進入，或使用兩組光電開關，分別距輸送帶高40cm,90cmAttention points關關注點注點:8. Access to the machinery shall be provided by interlocked access doors. (Minimum Safety Category 3). Access doors must be made accessible by crossing bridges if necessary設置

33、具有聯鎖開關的防護門以進入機器； (安全類別至少為3類).如需要，應設置橫跨橋接近防護門。Different interlock systems may apply可以使用不同的聯鎖系統:- Double key system (fortress type) with both a mechanical and electronical lock同時配有機械鎖和電子鎖的雙鎖系統（ fortress type ）- Single key system (with master key on the electrical cabinet or control panel)單鎖系統（配電柜或控制板上

34、帶有鎖）- A reset command must be given before re-start command is accepted必須先復位才可以重新啟動。必須先復位才可以重新啟動。- Interlocks must be robust and not easy to override 聯鎖防護門必須堅固耐用且不易失靈聯鎖防護門必須堅固耐用且不易失靈7778De-crater/Crater 卸箱機/裝箱機(4)Attention points關注關注點點:9. Entrance and exit points of crates are safeguarded with fixed

35、 fences only allowing a letter box typeopening to let a crate pass through. The height of the opening shall never be more than 50cm. If a door is needed on the side guarding, interlock is must. 塑箱進出點的開口處設置固定柵欄進行防護，開口大小只能允許塑箱通過。開口的高度不應高于塑箱進出點的開口處設置固定柵欄進行防護，開口大小只能允許塑箱通過。開口的高度不應高于50CM.如果要在側面防護上開門，則必須設置

36、聯鎖開關。如果要在側面防護上開門，則必須設置聯鎖開關。999 Interlocks must be robust and not easy to override 聯鎖裝置必須堅固耐用且不易失靈聯鎖裝置必須堅固耐用且不易失靈- A reset command must be given before the re-start command is accepted 必須先復位才可以重新啟動。必須先復位才可以重新啟動。1Modules & Content分類和目錄4FLT Loading/Un-loading point叉車裝卸點4De-palletiser/Palletiser卸垛機/

37、碼垛機4Pallet Stacker/De-stacker托盤碼垛機/卸垛機4De-crater/Crater卸箱機/裝箱機4Carton former成型機4Carton sealer封箱機4Crate Turner翻箱機4Crate Washer洗箱機4Crate Buffer 塑箱提升機4Bottle Washer洗瓶機4Filler裝酒機4Tunnel Pasteuriser 隧道式巴式殺菌機4Labeler貼標機4EBI空瓶檢驗機4Top Saw割紙箱機4Conveyors輸送帶4General Requirements一般要求4Acceptance Checklist驗收檢查清單C

38、rate Buffer塑箱提升機Attention points:關注點：關注點：1.Access is deterred by fixed fencing of minimum 2m high 設置至少2m高的固定柵欄進行隔離，防止人員進入2. Entrance and exit points of crates are safeguarded with fixed fences only allowing a letter box type opening to let a crate pass through. The height of the opening shall never

39、be more than 50cm.塑箱進出點的開口處設置固定柵欄進行防護塑箱進出點的開口處設置固定柵欄進行防護，開口大小只能允許塑箱，開口大小只能允許塑箱通過。開口高度不得大于通過。開口高度不得大于50cm3. Access to the machinery shall be provided by interlocked access doors.固定柵欄上如需開門，應設置聯鎖開關:Different interlock systems may apply:可以使用不同種類的聯鎖- Double key system (fortress type) with both a mechanic

40、al and electronical lock 同時帶有機械鎖和電子鎖的雙鎖系統- Single key system (with master key on the electrical cabinet or control panel) 單鎖系統（配電柜或控制面板上有鑰匙）- A reset command must be given before re-start command is accepted 必須先復位才可以重新啟動。必須先復位才可以重新啟動。- Interlocks must be robust and not easy to override 聯鎖裝置必須是堅固耐用并不

41、易失靈聯鎖裝置必須是堅固耐用并不易失靈4. An access platform with self-closing gate formaintenance and repair purposes shall be installed為維修人員設置的進入平臺須設置可以關閉的門43212m Interlocks must be robust and not easy to override 聯鎖裝置應該堅固耐用且不易失靈聯鎖裝置應該堅固耐用且不易失靈- A reset command must be given before the re-start command is accepted必須先

42、復位才可以重新啟動。必須先復位才可以重新啟動。6. Hatches giving access to the inside of the BW must be fixed (only removable by using tools)洗瓶機觀察孔必須是封閉固定的（只能通過工具移除）56665Bottle Washer (3)Attention points關注關注點點:7. Bottle Washer hatches shall be safeguarded by double protection so that a sudden complete opening is made impos

43、sible, avoiding that operators get splashed by caustic洗洗瓶機倉口應該進行雙重防護，避免倉門突然打開，致使操作瓶機倉口應該進行雙重防護，避免倉門突然打開，致使操作工被堿液濺到。工被堿液濺到。77Bottle Washer (4)Attention points關注關注點點:8. Warning signs for hot surface or hot liquid must be foreseen as from 60C.超過60C熱表面或熱液體的警示標識必須清晰可見。- All direct accessible hot parts as

44、 from 70C shall be insulated必須將所有可以直接接觸到的、超過70C的發熱體進行保溫。9. Steampipes, direct accessible from ground level, shall ideally be guarded by screens 使用防護屏將通過地面就可以直接接觸到的蒸汽管道進行隔離。- Bottle Washers shall be equipped with an H2 extractor ventilator洗瓶機應配有洗瓶機應配有H2抽風機。抽風機。8889Bottle Washer (5)Attention points關關注

45、點注點:10. Access platforms for maintenance and repair purposes along the BW sides shall be equipped with a self-closing access gate 洗瓶機邊部用于維護和維修的平臺上應設置員工可以手動關閉的門，- The access gate shall never be tightened to the railing in its open position除特殊原因外，門應該一直處于關閉狀態除特殊原因外，門應該一直處于關閉狀態101010Bottle Washer洗瓶機 (6)

46、 Platform Guardrails: Guardrails are installed on working platforms, they must meet the following safety requirements (Dimensions in millimeter): 1 Handrail 2 Knee rail 3 Kick plate 4 Stanchion 5 Walking level 1 4 5 2 3 Attention points關注關注點點:11. A guardrail shall be installed on the roof of the Bot

47、tle Washer應該在洗瓶機頂部安裝護欄。12. The access to the roof shall be provided by a fix stairs. 有合適的階梯到達洗瓶機頂部。13. The access to the roof shall have a self-closing access gate with lock通向頂部的入口須有門- The access gate shall never be tightened to the railing in its open position，通道門應該一直處于關閉狀態11111212Modules & Con

48、tent分類和目錄4FLT Loading/Un-loading point叉車裝卸點4De-palletiser/Palletiser卸垛機/碼垛機4Pallet Stacker/De-stacker托盤碼垛機/卸垛機4De-crater/Crater卸箱機/裝箱機4Carton former成型機4Carton sealer封箱機4Crate Turner翻箱機4Crate Washer洗箱機4Crate Buffer塑箱提升機4Bottle Washer洗瓶機4Filler裝酒機4Tunnel Pasteuriser 隧道式巴式殺菌機4Labeler貼標機4EBI空瓶檢驗機4Top Sa

49、w割紙箱機4Conveyors輸送帶4General Requirements一般要求4Acceptance Checklist驗收檢查清單Filler裝酒機 (1)Attention points 關注關注點點:1.The frontside of the Filler shall be safeguarded by fixed screens and only allowing a bottle-shaped gap to let the bottle pass through 裝酒機正面應設置固定式防護門進行防護，只留有瓶子裝酒機正面應設置固定式防護門進行防護，只留有瓶子大小的間隙以便瓶

50、子通過。大小的間隙以便瓶子通過。2. Movable screens gaining access for maintenance and settings shall be interlocked。(Minimum Safety Category 3) 為方便人員進入維護和設置參數，裝酒機設置移動式防護門，應設置聯鎖開關。（安全類別至少為3類）- Interlocks must be robust and not easy to override 聯鎖裝置必須堅固耐用且不易失靈聯鎖裝置必須堅固耐用且不易失靈- A reset command must be given before the

51、re-start command is accepted 必須先復位才可以重新啟動。必須先復位才可以重新啟動。-點動器上加急停開關點動器上加急停開關2211112Filler 裝酒機 (2)Attention points關注關注點點:3. The backside of the Filler shall be safeguarded by fixed fencing and fixed screens (only removable by using tools) 裝酒機背面應該設置固定柵欄和固定防護進行防護（只能通過借助工具進行移除）4. Access doors shall be int

52、erlocked. (Minimum Safety Category 3). Access doors must be made accessible需要進出的防護門應該設置聯鎖開關，（安全類別為需要進出的防護門應該設置聯鎖開關，（安全類別為3類）類）且必須是容易進入的。且必須是容易進入的。- Interlocks must be robust and not easy to override 聯鎖裝置必須堅固耐用且不易失靈聯鎖裝置必須堅固耐用且不易失靈- A reset command must be given before the re-start command is accepted

53、. 必須先復位才可以重新啟動。必須先復位才可以重新啟動。433Extra requirements for all new machines with jog function （Jog for filler and labeler）4For jog function:4Two handed (two pushbutton) jog is required (with spacing of the pushbuttons greater than the distance of the width of a hand to avoid a one handed jog.)4An E-stop

54、should always be included on the jog control station4Only one jog control station (CST) can be enabled at any given time.4Only one safety door can be opened at one time for jog mode to be enabled.4The jog pushbutton station can only be enabled for its visible zone when a guard door is opened. (For e

55、xample, if a guard door is open on the front of a machine, the jog control station on the rear of the machine will not be enabled even though a guard door is opened. This is because the front guard door is out of the visible/safe zone for the rear CST.)4Confirm jog speed is programmed as slow/safe a

56、s possible yet still provide the needed functionality4Sign on machine in local language, (above the location of the CTS): Do not enter machine while the machine is in jog mode. Example of jog with two pushbuttons新設備點動器的要求新設備點動器的要求(適用于灌酒機和貼標機的點動器適用于灌酒機和貼標機的點動器)4點動器點動器:4點動器是雙手同時（兩個控制按鈕）操作點動器是雙手同時（兩個控制

57、按鈕）操作的。的。 (兩個按鈕的距離大于人手的寬度。避免兩個按鈕的距離大于人手的寬度。避免一只手操作兩個按鈕一只手操作兩個按鈕)。4點動器上需安裝急停按鈕。點動器上需安裝急停按鈕。4只在特定情況下激活一個按鈕點動控制的模式。只在特定情況下激活一個按鈕點動控制的模式。4只有打開一扇安全門時才可以啟動點動模式。只有打開一扇安全門時才可以啟動點動模式。4當打開的安全門在視線范圍內時，才可以啟動當打開的安全門在視線范圍內時，才可以啟動該處的點動模式。該處的點動模式。 (例如：如果在機器正面的安全門打開，點動器例如：如果在機器正面的安全門打開，點動器在機器側面，無法看到打開的安全門，這種情在機器側面，無

58、法看到打開的安全門，這種情況下無法啟動點動模式。況下無法啟動點動模式。 4確認點動速度，在保證功能的情況下越慢確認點動速度，在保證功能的情況下越慢/安安全越好。全越好。4在點動器上方張貼標識：在點動器上方張貼標識：“禁止點動狀態下進禁止點動狀態下進入機器入機器”。雙手操作的點動器例雙手操作的點動器例子子Modules & Content分類和目錄4FLT Loading/Un-loading point叉車裝卸點4De-palletiser/Palletiser卸垛機/碼垛機4Pallet Stacker/De-stacker托盤碼垛機/卸垛機4De-crater/Crater卸箱機/

59、裝箱機4Carton former成型機4Carton sealer封箱機4Crate Turner翻箱機4Crate Washer洗箱機4Crate Buffer塑箱提升機4Bottle Washer洗瓶機4Filler裝酒機4Tunnel Pasteuriser 隧道式巴式殺菌機4Labeler貼標機4EBI空瓶檢驗機4Top Saw割紙箱機4Conveyors輸送帶4General Requirements一般要求4Acceptance Checklist驗收檢查清單 Platform Guardrails: Guardrails are installed on working pla

60、tforms, they must meet the following safety requirements (Dimensions in millimeter): 1 Handrail 2 Knee rail 3 Kick plate 4 Stanchion 5 Walking level 1 4 5 2 3 Tunnel Pasteuriser 隧道式巴式殺菌機Attention points關注關注點點:1. The frontside of the tunnel pasteuriser shall be safeguarded by movable screens, protecting operators against burstin