無線樓宇數據傳輸系統的仿真

1、無線樓宇數據傳輸系統的仿真1. 摘要本實驗的內容是無線樓宇數據傳輸仿真，分析915M的樓宇通信特性，建立樓宇數據通信系統的仿真模型，采用無線收發芯片NRF905，依據其性能參數來判斷樓宇內兩點能否進行數據傳輸。2. 實驗內容：無線樓宇數據傳輸系統的仿真。分析915M的樓宇通信特性，建立樓宇數據通信系統的仿真模型，采用無線收發芯片NRF905，依據其性能參數來判斷樓宇內兩點之間能否進行數據傳輸。路徑損耗（Path Loss）主要是由三個方面的因素導致的：一是發射機和接收機之間相隔的距離；二是同一樓層的軟隔板；三是豎直方向的混凝土墻。它們?cè)斐傻穆窂綋p耗可用以下公式表示：PL(d)dB=20*log

2、10(4*pi*d/l)+p*AF(soft partition)dB+q*AF(concret wall)dB.其中d是收發之間相隔的距離(m)，l是芯片發出信號的波長（l= c / f = 300 M / 914 M = 0. m），p是軟隔墻數，其相應的AF(soft partition)=1.39dB,q是混凝土墻數,其相應的 AF(concret wall)=2.38dB。由此，考慮此仿真系統為二維。即：當知道軟隔墻數p和混凝土墻數q時，根據平面兩點之間距離公式，可以得到收發之間相隔的近似距離：d=sqrt(p*x)2+(q*y)2).其中x為每?jī)蓚€(gè)軟隔墻之間的水平距離，y為每?jī)蓚€(gè)混

3、凝土墻樓層之間的豎直高度。x,y為已知參數。所以程序需輸入p、q兩個變量，即可得到收發之間相隔的近似距離，進而算出收發之間的路徑損耗。無線收發芯片NRF905的最大輸出功率為10dBm=-20dB，接收分辨功率（能接收到的最小功率）為-100dBm=-130dB，所以其能允許的最大衰減范圍為-20-（-130）=110dB，當路徑損耗在此范圍內芯片能夠收發信號。程序中先算出發射機和接收機之間的路徑損耗，再與110dB相比較。若小于110dB，則在允許的衰減范圍內，能夠進行無線樓宇數據通信；若大于110dB，則超出允許的衰減范圍，不能進行無線樓宇數據通信。最后，程序分別繪制出路徑損耗隨軟隔墻數p

4、和混凝土墻數q的變化曲線。即同一樓層（q=0）的路徑損耗隨軟隔墻數的增加（水平距離的增大）的變化曲線；和豎直方向上(p=0)路徑損耗隨混凝土墻數的增加（豎直高度的增加）的變化曲線。3. 實驗程序及結果：function varargout = Wirelesscommunication_building(varargin)% WIRELESSCOMMUNICATION_BUILDING M-file for Wirelesscommunication_building.fig% WIRELESSCOMMUNICATION_BUILDING, by itself, creates a new W

5、IRELESSCOMMUNICATION_BUILDING or raises the existing% singleton*.% H = WIRELESSCOMMUNICATION_BUILDING returns the handle to a new WIRELESSCOMMUNICATION_BUILDING or the handle to% the existing singleton*.% WIRELESSCOMMUNICATION_BUILDING('CALLBACK',hObject,eventData,handles,.) calls the local%

6、 function named CALLBACK in WIRELESSCOMMUNICATION_BUILDING.M with the given input arguments.% WIRELESSCOMMUNICATION_BUILDING('Property','Value',.) creates a new WIRELESSCOMMUNICATION_BUILDING or raises the% existing singleton*. Starting from the left, property value pairs are% applie

7、d to the GUI before Wirelesscommunication_building_OpeningFunction gets called. An% unrecognized property name or invalid value makes property application% stop. All inputs are passed to Wirelesscommunication_building_OpeningFcn via varargin.% *See GUI Options on GUIDE's Tools menu. Choose "

8、;GUI allows only one% instance to run (singleton)".% See also: GUIDE, GUIDATA, GUIHANDLES% Edit the above text to modify the response to help Wirelesscommunication_building% Last Modified by GUIDE v2.5 18-May-2006 22:38:07% Begin initialization code - DO NOT EDITgui_Singleton = 1;gui_State = st

9、ruct('gui_Name', mfilename, . 'gui_Singleton', gui_Singleton, . 'gui_OpeningFcn', Wirelesscommunication_building_OpeningFcn, . 'gui_OutputFcn', Wirelesscommunication_building_OutputFcn, . 'gui_LayoutFcn', , . 'gui_Callback', );if nargin && isch

10、ar(varargin1) gui_State.gui_Callback = str2func(varargin1);endif nargout varargout1:nargout = gui_mainfcn(gui_State, varargin:);else gui_mainfcn(gui_State, varargin:);end% End initialization code - DO NOT EDIT% - Executes just before Wirelesscommunication_building is made visible.function Wirelessco

11、mmunication_building_OpeningFcn(hObject, eventdata, handles, varargin)% This function has no output args, see OutputFcn.% hObject handle to figure% eventdata reserved - to be defined in a future version of MATLAB% handles structure with handles and user data (see GUIDATA)% varargin command line argu

12、ments to Wirelesscommunication_building (see VARARGIN)% Choose default command line output for Wirelesscommunication_buildinghandles.output = hObject;% Update handles structureguidata(hObject, handles);% UIWAIT makes Wirelesscommunication_building wait for user response (see UIRESUME)% uiwait(handle

13、s.figure1);% - Outputs from this function are returned to the command line.function varargout = Wirelesscommunication_building_OutputFcn(hObject, eventdata, handles) % varargout cell array for returning output args (see VARARGOUT);% hObject handle to figure% eventdata reserved - to be defined in a f

14、uture version of MATLAB% handles structure with handles and user data (see GUIDATA)% Get default command line output from handles structurevarargout1 = handles.output;function edit1_Callback(hObject, eventdata, handles)% hObject handle to edit1 (see GCBO)% eventdata reserved - to be defined in a fut

15、ure version of MATLAB% handles structure with handles and user data (see GUIDATA)% Hints: get(hObject,'String') returns contents of edit1 as text% str2double(get(hObject,'String') returns contents of edit1 as a double% Read the input value edit1 = str2double(get(hObject,'String&#

16、39;);% Check whether the input is a numberif isnan(edit1) set(hObject, 'String', 1); errordlg('Input must be a number','Error');endif (edit1<0|edit1>4) errordlg('發射機和接收機相隔的樓層數必須在零到四層之間','Error');end;% Save the new valuedata = getappdata(gcbf, 'metric

17、data');data.edit1 = edit1;setappdata(gcbf, 'metricdata', data);% - Executes during object creation, after setting all properties.function edit1_CreateFcn(hObject, eventdata, handles)% hObject handle to edit1 (see GCBO)% eventdata reserved - to be defined in a future version of MATLAB% ha

18、ndles empty - handles not created until after all CreateFcns called% Hint: edit controls usually have a white background on Windows.% See ISPC and COMPUTER.if ispc && isequal(get(hObject,'BackgroundColor'), get(0,'defaultUicontrolBackgroundColor') set(hObject,'BackgroundC

19、olor','white');endfunction edit2_Callback(hObject, eventdata, handles)% hObject handle to edit2 (see GCBO)% eventdata reserved - to be defined in a future version of MATLAB% handles structure with handles and user data (see GUIDATA)% Hints: get(hObject,'String') returns contents

20、of edit2 as text% str2double(get(hObject,'String') returns contents of edit2 as a double% Read the input valueedit2 = str2double(get(hObject,'String');% Check whether the input is a numberif isnan(edit2) set(hObject, 'String', 1); errordlg('Input must be a number',

21、9;Error');endif edit2<0 errordlg('發射機和接收機相隔的距離必須大于0','Error');end;% Save the new valuedata = getappdata(gcbf, 'metricdata');data.edit2 = edit2;setappdata(gcbf, 'metricdata', data);% - Executes during object creation, after setting all properties.function edit2_

22、CreateFcn(hObject, eventdata, handles)% hObject handle to edit2 (see GCBO)% eventdata reserved - to be defined in a future version of MATLAB% handles empty - handles not created until after all CreateFcns called% Hint: edit controls usually have a white background on Windows.% See ISPC and COMPUTER.

23、if ispc && isequal(get(hObject,'BackgroundColor'), get(0,'defaultUicontrolBackgroundColor') set(hObject,'BackgroundColor','white');endfunction edit3_Callback(hObject, eventdata, handles)% hObject handle to edit3 (see GCBO)% eventdata reserved - to be defined i

24、n a future version of MATLAB% handles structure with handles and user data (see GUIDATA)% Hints: get(hObject,'String') returns contents of edit3 as text% str2double(get(hObject,'String') returns contents of edit3 as a double% Read the input valueedit3 = str2double(get(hObject,'St

25、ring');% Check whether the input is a numberif isnan(edit3) set(hObject, 'String', 1); errordlg('Input must be a number','Error');endif edit3<0 errordlg('收發之間的軟隔墻數必須大于或等于0','Error');end;% Save the new valuedata = getappdata(gcbf, 'metricdata');d

26、ata.edit3 = edit3;setappdata(gcbf, 'metricdata', data);% - Executes during object creation, after setting all properties.function edit3_CreateFcn(hObject, eventdata, handles)% hObject handle to edit3 (see GCBO)% eventdata reserved - to be defined in a future version of MATLAB% handles empty

27、- handles not created until after all CreateFcns called% Hint: edit controls usually have a white background on Windows.% See ISPC and COMPUTER.if ispc && isequal(get(hObject,'BackgroundColor'), get(0,'defaultUicontrolBackgroundColor') set(hObject,'BackgroundColor',&#

28、39;white');endfunction edit4_Callback(hObject, eventdata, handles)% hObject handle to edit4 (see GCBO)% eventdata reserved - to be defined in a future version of MATLAB% handles structure with handles and user data (see GUIDATA)% Hints: get(hObject,'String') returns contents of edit4 as

29、text% str2double(get(hObject,'String') returns contents of edit4 as a double% Read the input valueedit4 = str2double(get(hObject,'String');% Check whether the input is a numberif isnan(edit4) set(hObject, 'String', 1); errordlg('Input must be a number','Error'

30、);endif edit4<0 errordlg('收發之間的混凝墻數必須大于或等于0','Error');end;% Save the new valuedata = getappdata(gcbf, 'metricdata');data.edit4 = edit4;setappdata(gcbf, 'metricdata', data);% - Executes during object creation, after setting all properties.function edit4_CreateFcn(hO

31、bject, eventdata, handles)% hObject handle to edit4 (see GCBO)% eventdata reserved - to be defined in a future version of MATLAB% handles empty - handles not created until after all CreateFcns called% Hint: edit controls usually have a white background on Windows.% See ISPC and COMPUTER.if ispc &

32、;& isequal(get(hObject,'BackgroundColor'), get(0,'defaultUicontrolBackgroundColor') set(hObject,'BackgroundColor','white');end% - Executes on button press in pushbutton1.function pushbutton1_Callback(hObject, eventdata, handles)% hObject handle to pushbutton1 (see GCBO)% eventdata reserved - to be defined in a future version of MATLAB% handles structure with handles and user data (see GUIDATA)data = getappdata(gcbf, 'metricdata');p=data.edit3; %收發之間的軟隔墻數q=data.edit4; %收發之間的混凝土墻數x=5; %每?jī)蓚€(gè)軟隔墻之間的距離(m)y=3; %每一樓層的高度(m)d=sq