GSM手機測試參數和測試內容

1、GSM基本參數：發射頻率范圍GSM850GSM ：890-915MHZEGSM ：880-915MHZDCS1800 ：1710-1785MHZPCS1900:接收頻率范圍GSM850GSM ：935-960MHZEGSM ：925-960MHZDCS1800 ：1805-1880MHZPCS1900:TX-RX雙頻間隔GSM850GSM/EGSM ：45MHZDCS1800 ：95MHZPCS1900:信道間隔GSM850:200KHZGSM/EGSM ：200KHZDCS1800 ：200KHZPCS1900: 200KHZ信道數GSM850:GSM ：124（1-124）EGSM ：50

2、（975-10230）DCS1800 ： 374（512-885）PCS1900: 299(512-810)功率等級GSM850GSM/EGSM ：Class4(33+/-2dBm)DCS1800 ：Class1(30+/-2dBm)PCS1900: Class1(30+/-2dBm)發射最大電流250mAGSM/GSM850射頻指標發射頻率輸出相位與頻率誤差DCS/PCS射頻指標發射頻率輸出：相位與頻率誤差后線測試項目英譯漢：BT/RF測試內容_|1|Initialize System初始化系統_|2|Off current check關機電流檢測_|3|Power on Check開機檢測

3、_|4|Check Serial number檢查SN_|5|Current of test mode|33.92|1.06|75|30|mA測試模式下的電流35+/-4mA_|6|Check SIM pin|0|.56|0|0|-檢查SIM卡_|7|ADC value of 4.2V|1182|.48|1500|200|-檢測電池校準_|8|ADC Value of 3.4 V|974|.52|1500|200|-檢測電池校準_|9|Voltage Calibration|0|2.05|0|0|-檢測電池校準_|10|Write Default Radio table|0|2.45|0|0|

4、-寫入默認的射頻參數_|11|Verify Radio table|0|1.45|0|0|-檢測射頻參數_|12|Wait for GSM Test set control|0|.03|0|0|-對CMU200控制_|13|Initialize Test set|0|5.42|0|0|-對CMU200控制_|14|Switch to GSM1800 NSIG Mode|0|0|0|0|-對CMU200控制_|15|Switch RF Path to connector|0|.02|0|0|-對CMU200控制_|16|Config to BCH+TCH Mode|0|0|0|0|-對CMU20

5、0控制_|17|Calculate FoiInit|1827|5.22|4000|800|-校準26M晶振_|18|Validate FOIinit Value|0|1.42|0|0|-保存校準值_|19|Switch GSM900 NSIG Mode|0|0|0|0|-對CMU200控制_|20|Config Test set to CW Mode|0|.52|0|0|-對CMU200控制_|21|Set RFG for P1 GSM|0|.44|0|0|-對CMU200控制_|22|Measure Rx Power|-62.375|.44|-43|-83|dbm檢測接受信號（應該在-63d

6、Bm左右）_|23|Calculate P1 GSM|-100|0|-80|-110|dbm校準接受信號_|24|Save P1 GSM to EEPROM|0|.02|0|0|-保存校準值_|25|Switch to GSM1800 NSIG Mode|0|0|0|0|-對CMU200控制_|26|Set RFG for P1 DCS|0|.45|0|0|-對CMU200控制_|27|Measure Rx Power|-61.125|.45|-43|-83|-檢測接收信號（應該在-63dBm左右）_|28|Calculate P1 DCS|-101|.01|-80|-110|dbm校準接收信

7、號_|29|Save P1 DCS to EEPROM|0|1.75|0|0|-保存校準值_|30|Switch to GSM900 NSIG Mode|0|0|0|0|-對CMU200控制_|31|Adjust GSM Rx FineGain|0|4.61|0|0|-校準GSM各頻段的接收_|32|Save GSM FineGain to EEPROM|0|.01|0|0|-保存校準值_|33|Switch to GSM1800 NSIG|0|0|0|0|-對CMU200控制_|34|Adjust DCS Rx FineGain|0|4.61|0|0|-校準DCS各頻段的接收_|35|Sav

8、e DCS FineGain to EEPROM|0|.02|0|0|-保存校準值_|36|Switch to GSM900 NSIG mode|0|.01|0|0|-對CMU200控制_|37|Config to BCH+TCH Mode|0|0|0|0|-對CMU200控制_|38|Initialize GSM power calibration|0|0|0|0|-對CMU200控制_|39|Measure Power(32,5)|32.04|1.42|38|20|dbm測量32信道5功率級的功率_|40|Measure Power(124,5)|32.32|.58|38|20|dbm測量

9、124信道5功率級的功率_|41|Measure Power(32,10)|22.5|.58|33|13|dbm測量32信道10功率級的功率_|42|Measure Power(32,15)|11.84|.58|23|3|dbm測量32信道15功率級的功率_|43|Measure Power(32,19)|5.48|1.01|11|1|dbm測量32信道19功率級的功率_|44|Solve Coefficients GSM|0|.05|0|0|-對CMU200控制_|45|Calculate H15 for PCL5 (GSM)|672|.03|1023|35|-校準發射應該在700以下_|4

10、6|Calculate H15 for PCL6 (GSM)|624|.01|1023|35|-校準發射_|47|Calculate H15 for PCL7(GSM)|568|.03|1023|35|-校準發射_|48|Calculate H15 for PCL8(GSM)|520|.01|1023|35|-校準發射_|49|Calculate H15 for PCL9(GSM)|480|.03|1023|35|-校準發射_|50|Calculate H15 for PCL10(GSM)|452|.02|1023|35|-校準發射_|51|Calculate H15 for PCL11(GS

11、M)|424|.03|1023|35|-校準發射_|52|Calculate H15 for PCL12(GSM)|400|.02|1023|35|-校準發射_|53|Calculate H15 for PCL13(GSM)|380|.03|1023|35|-校準發射_|54|Calculate H15 for PCL14(GSM)|364|0|1023|35|-校準發射_|55|Calculate H15 for PCL15(GSM)|348|.02|1023|35|-校準發射_|56|Calculate H15 for PCL16(GSM)|332|.01|1023|35|-校準發射_|5

12、7|Calculate H15 for PCL17(GSM)|320|.01|1023|35|-校準發射_|58|Calculate H15 for PCL18(GSM)|308|0|1023|35|-校準發射_|59|Calculate H15 for PCL19(GSM)|298|.01|1023|35|-校準發射_|60|Save GSM calibration result|0|0|0|0|-保存校準值_|61|Config to BCH+TCH Mode|0|.02|0|0|-對CMU200控制_|62|GSM H0 Alignment(PCL5)|247|1.17|290|30|-

13、校準功率包絡_|63|GSM H0 Alignment(PCL19)|243|8.64|280|30|-校準功率包絡_|64|Calculate H0 for all GSM PCL|0|1.86|0|0|-校準功率包絡_|65|Switch to GSM1800 NSIG mode|0|.02|0|0|-對CMU200控制_|66|Config to BCH+TCH Mode|0|0|0|0|-對CMU200控制_|67|Initialize DCS Power calibration|0|.02|0|0|-對CMU200控制_|68|Measure Power(698,0)|28.86|2

14、.64|35|25|dbm測量698信道0功率級的功率_|69|Measure Power(512,0)|28.95|.59|38|20|dbm測量512信道0功率級的功率_|70|Measure Power(698,5)|18.75|.56|30|10|dbm測量698信道5功率級的功率_|71|Measure Power(698,10)|8.31|.56|20|0|dbm測量698信道10功率級的功率_|72|Measure Power(698,15)|1.63|1.42|10|-2|dbm測量698信道15功率級的功率_|73|Solve Coefficients DCS|0|.05|0

15、|0|-對CMU200控制_|74|Calculate H15 for PCL0(DCS)|736|.03|1023|35|-校準發射應該在750以下_|75|Calculate H15 for PCL1(DCS)|640|.01|1023|35|-校準發射_|76|Calculate H15 for PCL2(DCS)|560|.03|1023|35|-校準發射_|77|Calculate H15 for PCL3(DCS)|512|.02|1023|35|-校準發射_|78|Calculate H15 for PCL4(DCS)|472|.03|1023|35|-校準發射_|79|Calc

16、ulate H15 for PCL5(DCS)|440|.02|1023|35|-校準發射_|80|Calaulate H15 for PCL6(DCS)|408|.03|1023|35|-校準發射_|81|Calculate H15 for PCL7(DCS)|388|.03|1023|35|-校準發射_|82|Calculate H15 for PCL8(DCS)|364|.02|1023|35|-校準發射_|83|Calculate H15 for PCL9(DCS)|348|.03|1023|35|-校準發射_|84|Calculate H15 for PCL10(DCS)|332|.

17、01|1023|35|-校準發射_|85|Calculate H15 for PCL11(DCS)|316|.03|1023|35|-校準發射_|86|Calculate H15 for PCL12(DCS)|304|.01|1023|35|-校準發射_|87|Calculate H15 for PCL13(DCS)|292|.03|1023|35|-校準發射_|88|Calculate H15 for PCL14(DCS)|280|.02|1023|35|-校準發射_|89|Calculate H15 for PCL15(DCS)|270|.03|1023|35|-校準發射_|90|Save

18、 DCS calibration result|0|.02|0|0|-保存校準值_|91|Config to BCH+TCH Mode|0|.02|0|0|-對CMU200控制_|92|DCS H0 Alignment(PCL0)|210|.7|330|30|-校準功率包絡_|93|DCS H0 Alignment(PCL15)|222|5.78|280|30|-校準功率包絡_|94|Calculate h0 for all DCS PCL|0|3.72|0|0|-校準功率包絡FT(Call) 測試內容_|95|Initialize System|0|4.98|0|0|-對CMU200控制_|

19、96|Initialize GSM Test set|0|5.45|0|0|-對CMU200控制_|97|Reset Test Set|0|2.56|0|0|對CMU200控制_|98|Power On MS|0|2.78|0|0|-開機檢測_|99|Switch to GSM900 signalling mode|0|.01|0|0|-對CMU200控制_|100|Switch RF Path to connector|0|.02|0|0|-對CMU200控制_|101|Setup BCCH|0|.64|0|0|-對CMU200控制_|102|Setup TCH|0|.03|0|0|-對CM

20、U200控制_|103|Wait for MS Registering|0|20.7|0|0|-等待網絡注冊_|104|MS Call to BS|1|36.48|1|1|用手機Call CMU_|105|Change PCL(975,19)|0|2.52|0|0|-切換測試信道和功率_|106|Start Tx Measurement(975,19)|0|2.36|0|0|開始測試功率_|107|Average Power(975,19)|4.77|.02|10|0|測試平均功率_|108|Peak Phs Error(975,19)|4.05|.01|20|0|Deg測試峰值相位誤差_|1

21、09|RMS Phs Error(975,19)|1.73|.02|5|0|Deg測試均方根相位誤差_|110|Wait Time|0|2.02|0|0|等待2秒_|111|Frequency Error(975,19)|47.33|.01|90|-90|Hz測試頻率誤差_|112|Time Mask(975,19)|0|.01|0|0|-測試功率包絡_|113|Change PCL(975,5)|0|2.52|0|0|-切換功率_|114|Start Tx Measurement(975,5)|0|2.33|0|0|開始測試功率_|115|Average Power(975,5)|32.17

22、|.02|35|31|測試平均功率_|116|Peak Phs Error(975,5)|3.99|.02|20|0|Deg測試峰值相位誤差_|117|RMS Phs Error(975,5)|1.63|.01|5|0|Deg測試均方根相位誤差_|118|Wait Time|0|1.01|0|0|等待2秒_|119|Frequency Error(975,5)|34.68|.02|90|-90|Hz測試頻率誤差_|120|Time Mask(975,5)|0|.02|0|0|-測試功率包絡_|121|switching spectrum(975,5)|0|.53|0|0|-測試開關頻譜_|12

23、2|ORFS Offset -1200Khz(975,5)|-47.55|0|-24|-99|dbm測試開關頻譜_|123|ORFS Offset -800Khz(975,5)|-42.85|0|-21|-99|dbm測試開關頻譜_|124|ORFS Offset -600Khz(975,5)|-33.3|0|-21|-99|dbm測試開關頻譜_|125|ORFS Offset -400Khz(975,5)|-28.55|0|-19|-99|dbm測試開關頻譜_|126|ORFS Offset +400Khz(975,5)|-27.44|0|-19|-99|dbm測試開關頻譜_|127|ORF

24、S Offset +600Khz(975,5)|-29.99|0|-21|-99|dbm測試開關頻譜_|128|ORFS Offset +800Khz(975,5)|-43.93|0|-21|-99|dbm測試開關頻譜_|129|ORFS Offset +1200Khz(975,5)|-45.85|0|-24|-99|dbm測試開關頻譜_|130|Start BER Measurement(975,-106)|0|1.81|0|0|-開始測試RBER_|131|RBER ClassII(975,-106)|.1|.01|2.44|0|%測試RBER_|132|FER(975,-106)|0|0

25、|0|0|-測試FER_|133|Rx Level(975,-106)|5|0|11|1|-測試接收等級_|134|Rx Quality(975,-106)|0|0|4|0|-測試接收質量_|135|Change TCH(40,19)|0|2.52|0|0|-切換測試信道和功率_|136|Start Tx Measurement(40,19)|0|.23|0|0|開始測試功率_|137|Average Power(40,19)|4.74|.02|10|0|測試平均功率_|138|Peak Phs Error(40,19)|4.31|.01|20|0|Deg測試峰值相位誤差_|139|RMS P

26、hs Error(40,19)|1.58|.01|5|0|Deg測試均方根相位誤差_|140|Wait Time|0|1.02|0|0|等待2秒_|141|Frequency Error(40,19)|26.67|.02|90|-90|Hz測試頻率誤差_|142|Time Mask(40,19)|0|.01|0|0|-測試功率包絡_|143|Change PCL(40,5)|0|2.51|0|0|-切換功率_|144|Start Tx Measurement(40,5)|0|.22|0|0|開始測試功率_|145|Average Power(40,5)|32.11|0|35|31|測試平均功率

27、_|146|Peak Phs Error(40,5)|4.1|0|20|0|Deg測試峰值相位誤差_|147|RMS Phs Error(40,5)|1.55|0|5|0|Deg測試均方根相位誤差_|148|Wait Time|0|1.01|0|0|等待2秒_|149|Frequency Error(40,5)|13.95|.02|90|-90|Hz測試頻率誤差_|150|Time Mask(40,5)|0|.02|0|0|-測試功率包絡_|151|switching spectrum(40,5)|0|.42|0|0|-測試開關頻譜_|152|ORFS Offset -1200Khz(40,5

28、)|-47.08|0|-24|-99|dbm測試開關頻譜_|153|ORFS Offset -800Khz(40,5)|-42.97|0|-21|-99|dbm測試開關頻譜_|154|ORFS Offset -600Khz(40,5)|-33.61|0|-21|-99|dbm測試開關頻譜_|155|ORFS Offset -400Khz(40,5)|-28.33|0|-19|-99|dbm測試開關頻譜_|156|ORFS Offset +400Khz(40,5)|-27.21|0|-19|-99|dbm測試開關頻譜_|157|ORFS Offset +600Khz(40,5)|-29.72|0

29、|-21|-99|dbm測試開關頻譜_|158|ORFS Offset +800Khz(40,5)|-44.32|0|-21|-99|dbm測試開關頻譜_|159|ORFS Offset +1200Khz(40,5)|-47.31|0|-24|-99|dbm測試開關頻譜_|160|Tx Max current(GSM)|255.8|.05|400|200|mA檢測GSM最大發射電流_|161|Start BER Measurement(40,-106)|0|1.78|0|0|-開始測試RBER_|162|RBER ClassII(40,-106)|.49|.01|2.44|0|%測試RBER_

30、|163|FER(40,-106)|0|.03|0|0|-測試FER_|164|Rx Level(40,-106)|6|0|11|1|-測試接收等級_|165|Rx Quality(40,-106)|1|0|4|0|-測試接收質量_|166|Change TCH(124,19)|0|2.51|0|0|-切換測試信道和功率_|167|Start Tx Measurement(124,19)|0|.23|0|0|開始測試功率_|168|Average Power(124,19)|5.22|.02|10|0|測試平均功率_|169|Peak Phs Error(124,19)|4.41|.02|20

31、|0|Deg測試峰值相位誤差_|170|RMS Phs Error(124,19)|1.72|.01|5|0|Deg測試均方根相位誤差_|171|Wait Time|0|1.12|0|0|等待2秒_|172|Frequency Error(124,19)|17.76|0|90|-90|Hz測試頻率誤差_|173|Time Mask(124,19)|0|0|0|0|-測試功率包絡_|174|Change PCL(124,5)|0|2.52|0|0|-切換功率_|175|switching spectrum(124,5)|0|.42|0|0|-測試開關頻譜_|176|ORFS Offset -12

32、00Khz(124,5)|-46.88|0|-24|-99|dbm測試開關頻譜_|177|ORFS Offset -800Khz(124,5)|-42.2|0|-21|-99|dbm測試開關頻譜_|178|ORFS Offset -600Khz(124,5)|-32.22|0|-21|-99|dbm測試開關頻譜_|179|ORFS Offset -400Khz(124,5)|-27.14|0|-19|-99|dbm測試開關頻譜_|180|ORFS Offset +400Khz(124,5)|-26.74|0|-19|-99|dbm測試開關頻譜_|181|ORFS Offset +600Khz(

33、124,5)|-29.33|0|-21|-99|dbm測試開關頻譜_|182|ORFS Offset +800Khz(124,5)|-43.59|0|-21|-99|dbm測試開關頻譜_|183|ORFS Offset +1200Khz(124,5)|-47.03|0|-24|-99|dbm測試開關頻譜_|184|Start Tx Measurement(124,5)|0|.17|0|0|檢測GSM最大發射電流_|185|Average Power(124,5)|32.23|.02|35|31|測試平均功率_|186|Peak Phs Error(124,5)|4.21|.02|20|0|De

34、g測試峰值相位誤差_|187|RMS Phs Error(124,5)|1.7|.01|5|0|Deg測試均方根相位誤差_|188|Wait Time|0|1.01|0|0|等待2秒_|189|Frequency Error(124,5)|17.43|.02|90|-90|Hz測試頻率誤差_|190|Time Mask(124,5)|0|.02|0|0|-測試功率包絡_|191|Start BER Measurement(124,-106)|0|1.8|0|0|-開始測試RBER_|192|RBER ClassII(124,-106)|.03|0|2.44|0|%測試RBER_|193|FER

35、(124,-106)|0|0|0|0|-測試FER_|194|Rx Level(124,-106)|5|0|11|1|-測試接收等級_|195|Rx Quality(124,-106)|0|0|4|0|-測試接收質量_|196|Handover to DCS band|4|.64|4|4|-切換到DCS_|197|Change TCH(512,15)|0|2.52|0|0|-切換測試信道和功率_|198|Start Tx Measurement(512,15)|0|2.33|0|0|開始測試功率_|199|Average Power(512,15)|-.83|.01|5|-5|測試平均功率_|

36、200|Peak Phs Error(512,15)|5.87|.01|20|0|Deg測試峰值相位誤差_|201|RMS Phs Error(512,15)|2.18|.02|5|0|Deg測試均方根相位誤差_|202|Wait Time|0|1.02|0|0|等待2秒_|203|Frequency Error(512,15)|42.1|.01|180|-180|Hz測試頻率誤差_|204|Time Mask(512,15)|0|.01|0|0|-測試功率包絡_|205|Change PCL(512,0)|0|2.52|0|0|-切換功率_|206|switching spectrum(51

37、2,0)|0|.42|0|0|-測試開關頻譜_|207|ORFS Offset -1200Khz(512,0)|-46.29|.01|-27|-99|dbm測試開關頻譜_|208|ORFS Offset -800Khz(512,0)|-42.93|.02|-24|-99|dbm測試開關頻譜_|209|ORFS Offset -600Khz(512,0)|-38.94|.02|-24|-99|dbm測試開關頻譜_|210|ORFS Offset -400Khz(512,0)|-32.91|.01|-22|-99|dbm測試開關頻譜_|211|ORFS Offset +400Khz(512,0)|

38、-26.81|.01|-22|-99|dbm測試開關頻譜_|212|ORFS Offset +600Khz(512,0)|-35.95|.02|-24|-99|dbm測試開關頻譜_|213|ORFS Offset +800Khz(512,0)|-44.14|.02|-24|-99|dbm測試開關頻譜_|214|ORFS Offset +1200Khz(512,0)|-48.93|.01|-27|-99|dbm測試開關頻譜_|215|Start Tx Measurement(512,0)|0|.19|0|0|開始測試發射_|216|Average Power(512,0)|29.73|0|32|

39、28|測試平均功率_|217|Peak Phs Error(512,0)|7.34|0|20|0|Deg測試峰值相位誤差_|218|Wait Time|0|1.02|0|0|等待2秒_|219|Frequency Error(512,0)|31.38|.02|180|-180|Hz測試頻率誤差_|220|Time Mask(512,0)|0|.01|0|0|-測試功率包絡_|221|Start BER Measurement(512,-105)|0|1.84|0|0|-開始測試RBER_|222|RBER ClassII(512,-105)|.03|0|2.44|0|%測試RBER_|223|

40、FER(512,-105)|0|0|0|0|-測試FER_|224|Rx Level(512,-105)|7|0|11|2|-測試接收等級_|225|Rx Quality(512,-105)|0|0|4|0|-測試接收質量_|226|Change TCH(698,15)|0|2.51|0|0|-切換測試信道和功率_|227|Start Tx Measurement(698,15)|0|.17|0|0|開始測試功率_|228|Average Power(698,15)|-.34|.01|5|-5|測試平均功率_|229|Peak Phs Error(698,15)|4.79|.01|20|0|D

41、eg測試峰值相位誤差_|230|RMS Phs Error(698,15)|1.86|.02|5|0|Deg測試均方根相位誤差_|231|Wait Time|0|1.02|0|0|等待2秒_|232|Frequency Error(698,15)|17.63|.01|180|-180|Hz測試頻率誤差_|233|Time Mask(698,15)|0|.01|0|0|-測試功率包絡_|234|Change PCL(698,0)|0|2.52|0|0|-切換功率_|235|Start Tx Measurement(698,0)|0|.19|0|0|開始測試功率_|236|Average Powe

42、r(698,0)|29.39|0|32|28|測試平均功率_|237|Peak Phs Error(698,0)|10.25|0|20|0|Deg測試峰值相位誤差_|238|RMS Phs Error(698,0)|3.42|0|5|0|Deg測試均方根相位誤差_|239|Wait Time|0|1.01|0|0|等待2秒_|240|Frequency Error(698,0)|-8.39|.02|180|-180|Hz測試頻率誤差_|241|Time Mask(698,0)|0|.02|0|0|-測試功率包絡_|242|Start BER Measurement(698,-105)|0|1.

43、84|0|0|-開始測試RBER_|243|RBER ClassII(698,-105)|.03|0|2.44|0|%測試RBER_|244|FER(698,-105)|0|0|0|0|-測試FER_|245|Rx Level(698,-105)|8|.02|11|2|-測試接收等級_|246|Rx Quality(698,-105)|0|.02|4|0|-測試接收質量_|247|switching spectrum(698,0)|0|.42|0|0|-測試開關頻譜_|248|ORFS Offset -1200Khz(698,0)|-45.04|.02|-27|-99|dbm測試開關頻譜_|2

44、49|ORFS Offset -800Khz(698,0)|-42.62|.02|-24|-99|dbm測試開關頻譜_|250|ORFS Offset -600Khz(698,0)|-38.68|.01|-24|-99|dbm測試開關頻譜_|251|ORFS Offset -400Khz(698,0)|-32.14|.01|-22|-99|dbm測試開關頻譜_|252|ORFS Offset +400Khz(698,0)|-26.77|.02|-22|-99|dbm測試開關頻譜_|253|ORFS Offset +600Khz(698,0)|-36.29|.02|-24|-99|dbm測試開關

45、頻譜_|254|ORFS Offset +800Khz(698,0)|-42.41|.01|-24|-99|dbm測試開關頻譜_|255|ORFS Offset +1200Khz(698,0)|-47.9|.01|-27|-99|dbm測試開關頻譜_|256|Tx Max current(DCS)|191.9|.06|350|150|mA檢測最大DCS最大發射電流_|257|Change TCH(885,15)|0|2.51|0|0|-切換測試信道和功率_|258|Start Tx Measurement(885,15)|0|.23|0|0|開始測試功率_|259|Average Power(885,15)|-1.68|.02|5|-5|測試平均功率_|260|Peak Phs Error(885,15)|5.09|.02|20|0|Deg測試峰值相位誤差_|261|RMS Phs Error(885,15)|1.76|.01