DMX512控制器說明及介紹

1、DMX512空制器說明及介紹產品概述： products description? AT3010D控制器是一款帶LCD顯示，無線遙控，音頻輸入，地址編輯 的DMX控制器。? AT3010D controller is a DMX controller with LCD display,wireless control,audio input,IP edition.主要特點：main features? 輸入電壓：AC110V 或 AC220V。input voltage:AC110V or AC220v? 輸出 DMX 信號符合 DMX512/1990 標準。Input DMX signal

2、by DMX DMX512/1990 standard? 具有一個標準的DMX512輸出通道，可以實現最多170個全彩點的控制。? With a standard DMX512 output channel,it can realize 170 full color dot control at most? 內部具有常亮七彩，一致跳變，一致漸變，流水，追逐，中分，堆積等 燈光模式。? Internal has normally on seven color,consistency flash,consistencystrobe,smooth,pursuit,halve,accumulate a

3、nd other lighting mode? 各種變化效果可分別設定16種不同的變化速度和顏色選擇設定。? Each change effects can set 16 different change speed and color selection? 具有簡易的編程功能，可以方便的定義輸出燈光效果。? Simple program function,can easliy define input lighting effects? 編程可自由定義內部的各種變化模式為一個步驟。? Program can easily define all change mode inside to a

4、step.? 最多可定義8個獨立的循環的步驟。? define8 separate independent loop steps? 具有四個操作按鍵，可以方便進行功能操作。? With four operation keys,can easily operate? 具有LCD輸出指示，所有功能在LCD上均有操作提示。? With LCD output indication,all function is showed in the LCD.? 有無線遙控器可以遠距離調試和更改操作。? Wireless controller can be used in operation of remote

5、debug and change? 有音頻輸入接口，內置有兩種音頻模式。? With audio input connector,two inside audio mode? 具有DMX地址編輯功能，方便地址的修改。? With DMX IP edition function,convienent to modify the ID應用范圍：application? 小型變化效果的燈光系統的DMX接口輸出控制。? DMX connector output control of small change effects產品標準規格表 ：specification standard diagram產

6、品編號item no交流電壓輸入DC voltage input驅動能力drive power控制類型control way接線方式connecting wayAT3010D100 V-240V標準模組 (standard module)32PCSDMXRJ11典型性能參數 ：typifcal feature parameters性能項目feature project測試條件test condition最小值min典型值 typical最大值max輸出全彩節點 output full colornode一個RGB組為一節 點 a RGB group is anode1/170輸出DMX通道數O

7、utput DMX channel QTY1輸出DXM驅動能 力Output DMX drive power標準DMX模組standard DMX module1/32驅動距離drive instance無中繼白罟no repeater0/300m最大無損范圍 : max no-damage range參數項目parameter project代表符號represent sign最小值min最大值max備注remark輸入電壓(交流)Input voltage(DC)Vin_AC0AC260V工作溫度范圍 working temperatureTwork-20 C60 c實物照片：real o

8、bject photo機械尺寸：machine size項目 project規格說明 specification最小值min典型值 typical最大值max長度length160mm寬度width包拈天線 include antenna135mm厚度thickness32mm驅動輸出接口 RJ11: drive output connector端了termin al線顏色 linecolor功能 function備注remark1NC12NCU1UM3DMX-4DMX+15GND6SOUT地址編輯時有用到ID is available whenedittingion instruction操

9、作說明:operatWELCOME USEAT TECFWLOGYSTATIC RED 1R1G0G0STATIC YELLOW ElR1G1B0STATIC GKEEN 1ROG1BOSTATIC CYAN 1R0G1B1STATIC BLUE 1ROGOB1STATIC PURFLM1R1GQB1STATIC WHITE 1R1G1B11CHANGE FLASH 2C:OO S:31這是開機畫面，開機后顯示，約兩秒后自動進入到程序模式。按FUNTION鍵可以在下面的主功能間切換。Turn on picture,it is showed after turning on.Enter prog

10、ram mode automatically two seconds later.Press FUNTION to switch in the following main function常亮七色模式： normally on seven color mode1,紅色 red2,黃色 yellow3,綠色 green4.青色cyan5,藍色blue6,紫色 purple7,白色 whiteB,在常亮模式下，可以通過 UP, DOWN按鍵上來選取這七 種顏色之一。 Under this mode,select one of seven color by pressing UP,DOWN key

11、.C,可以通過FUNTION按鍵選取進入下一模式。Enter next mode through FUNTIOND,在常亮模式下，長按CONFIRM鍵進入保存參數頁面，確認, 下次上電進入當前狀態.Under this mode,press CONFIRM for a long time to enter save parameter page,confirm,enter current situation next timeE,功能代號1。Fucction code1A.整體跳變功能，輸出的顏色可以通過C:后面的參數修改. 默認為 00,即七彩跳變。Whole flash function,

12、output color can be modified by parameter after C:default 00,seven color flashB,短按CONFIRM鍵可以在顏色和時間上選擇要修改項.C為 顏色,S為顯示時間，口為當前被選取項.Press CONFIRM for a short time can modify color and time,C is color,S is time, is the current selected optionC.在時間參數被選取時，跳變的時間可以由UP, DOWN鍵加 或減。when time parameter selected,

13、Add or minus the flash time by UP,DOWN D.D.跳變時間共有16級，其中速度1速度最快。Flash time has 16 grades,1is the fastestE,顏色參數用16進制表示,bit0:紅色,bit1:黃,bit2:綠,bit3:青,bit4: 藍,bit5:紫,bit6:白,bit7:黑.如果該位為1,相應位的顏色被選取，為 0,則該色不輸出.如果為00,則默認七彩跳變.Color parameter adopts 16 system,bit0red,bit1yellow,bit2green,bit3 ,bit4 blue,bit5

14、purple,bit6 white,bit7 black.if it is 1,the corresponding color is selected.if it is 0,it doesn output the color.if it is 00,default 7 color flash.F,在顏色參數被選取時，按UP或DOWN可以加減該參數.When color parameter selected,pressUP or DOWN to add or reduce this parameter.G,可以通過FUNTION按鍵選取進入下一模式。Enter next mode through

15、 FUNTION key.H,在此模式下，長按CONFIRM鍵進入保存參數頁面，確認， 下次上電進入當前狀態.In this mode,press CONFIRM to enter save parameter page,confirm,enter current situation next time.I,功能代號2。Function code 2CHAHGE FABEl 3C:00S:lCHANGE F疝E2 4C:00S:lA.整體漸變功能，輸出的所有燈光按七色順序漸變，顏色不可 更改。Whole flash function,all output lighting flash acco

16、rding to seven color rank.color is unchangeable.B. 短按 CONFIRM 無意義.press CONFIRM for a short time has no meaning.C.漸變的時間可以由UP, DOWN鍵選取。Select UP/down to control flash time.D.漸變時間共有16級，其中速度1速度最快。Flash time has 16 grades,in which 1 is the fastestE,可以通過FUNTION按鍵選取進入下一模式。Enter next mode through FUNTIONF,

17、在此模式下，長按CONFIRM鍵進入保存參數頁面，確信， 下次上電進入當前狀態.In this mode ,press CONFIRM for a long time to enter save parameter page,confirm,enter current page next timeG,功能代號3。Function code 3A.整體漸明漸暗功能，輸出的顏色可以通過C:后面的參數修改.默認為 00,即七彩色。Whole brightness function,modify output color through parameter after C:B.短按CONFIRM鍵可以

18、在顏色和時間上選擇要修改項.C為 顏色,S為顯示時間，口為當前被選取項.Press CONFIRM for a short time to select the color and time to b modified.C is color,S is time, is current selected optionC.在時間參數被選取時，跳變的時間可以由UP, DOWN鍵加或 減。When time parameter selected,control flash time through UP,DOWND.跳變時間共有16級，其中速度1速度最快。STROBEhas 16 grades,in

19、which 1 is the fastestCHANGE MOVE 5C:00S:lCHANGE FLO6C:008:3E,顏色參數用16進制表示,bit0:紅色,bit1:黃,bit2:綠,bit3:青,bit4: 藍,bit5:紫,bit6:白,bit7:黑.如果該位為1,相應位的顏色被選取，為 0,則該色不輸出.如果為00,則默認七彩色.Colorparameteradopts16system,bit0red,bit1yellow,bit2 green,bit3 cyan bit4blue,bit5 purple,bit6 white,bit7 black.if it is 1,the

20、correspond color is selected.if it is 0,it doesHt output the color.if it is 00,default 7 color flash.F,在顏色參數被選取時，按UP或DOWN可以加減該參數.When color parameter selected,press UP/DOWN to add or reduce this parameterG,可以通過FUNTION按鍵選取進入下一模式。Enter next mode through FUNTIONH,在此模式下，長按CONFIRM鍵進入保存參數頁面，確認， 下次上電進入當前狀態

21、.In this mode,press CONFIRM to enter save parameter page,confirm,enter current situation next timeI,功能代號4。 Function code4A.七彩追逐功能，輸出的燈為七彩交替追逐變化，顏色不可更 改。Seven color pursuit,output light is seven color pursuit by turns,color is not changeable.B.短按CONFIRM無意義.Press CONFIRM for a short time has no meanin

22、g.C.漸變的時間可以由UP, DOWN鍵選取。Select flash time through UP,DOWND.漸變時間共有16級，其中速度1速度最快。Flash time has 16 grades,in which 1 is the fastestE,可以通過FUNTION按鍵選取進入下一模式。Enter next mode through FUNTIONI, F,在此模式下，長按CONFIRM鍵進入保存參數頁面，確 信，下次上電進入當前狀態.In this mode ,press CONFIRM for a long time to enter save parameter pag

23、e,confirm,enter current page next timeG,功能代號5。Function code5A.從小地址到大地址流水模式，輸出的顏色可以通過 C:后面的參數修改.默認為00,即七彩色Smooth mode:from small ID to big ID,modify output color through parameter after C:B.短按CONFIRM鍵可以在顏色和時間上選擇要修改項.C為 顏色,S為顯示時間，為當前被選取項.Press CONFIRM for a short time can modify color and time,C is co

24、lor,S is time, is the current selected optionC.在時間參數被選取時，跳變的時間可以由UP, DOWN鍵加或 減。When time parameter selected,control strobe timethrough UP,DOWN.D.跳變時間共有16級，其中速度1速度最快。strobe time has 16 grades,in which 1 is the fastestE,顏色參數用16進制表示,bit0:紅色,bit1:黃,bit2:綠,bit3:青,bit4: 藍,bit5:紫,bit6:白,bit7:黑.如果該位為1,相應位的顏

25、色被選取，為 0,則該色不輸出.如果為00,則默認七彩色.Color parameter adopts 16 system,bit0red,bit1yellow,bit2 green,bit3 cyan bit4blue,bit5 purple,bit6 white,bit7 black.if it is 1,the correspond color is selected.if it is 0,it doesn't output the color.if it is 00,default 7 colorF,在顏色參數被選取時，按UP或DOWN可以加減該參數.When color pa

26、rameter selected,add or reduce this parameter through UP,DOWNG,可以通過FUNTION按鍵選取進入下一模式。Enter next mode through FUNTIONH,在此模式下，長按CONFIRM鍵進入保存參數頁面，確認， 下次上電進入當前狀態.In this mode ,press CONFIRM for a long time to enter save parameter page,confirm,enter current page next timeI,功能代號6。 Function code6A.從大地址到小地址

27、流水模式，輸出的顏色可以通過 C:后面的 參數修改.默認為00,即七彩色。CHANGE FL0W<-E7C:00S:3Smooth mode from big ID to small ID,modify output color through parameter after C: default 00,seven colorB.短按CONFIRM鍵可以在顏色和時間上選擇要修改項.C為 顏色,S為顯示時間，口為當前被選取項.Press CONFIRM for a short time to select color and time to be modified. C is color,

28、S is time, is the current selected optionC.在時間參數被選取時，跳變的時間可以由UP, DOWN鍵加或減。When time parameter selected,add or reduce this time through UP,DOWND.跳變時間共有16級，其中速度1速度最快。strobe time has 16 grades,in which 1 is the fastestE,顏色參數用16進制表示,bit0:紅色,bit1:黃,bit2:綠,bit3:青,bit4: 藍,bit5:紫,bit6:白,bit7:黑.如果該位為1,相應位的顏色

29、被選取，為0,則該色不輸出.如果為00,則默認七彩色.Color parameter adopts 16 system,bit0red,bit1yellow,bit2 green,bit3 cyan bit4blue,bit5 purple,bit6 white,bit7 black.if it is 1,the correspond color is selected.if it is 0,it doesn't output the color.if it is 00,default 7 colorF,在顏色參數被選取時，按UP或DOWN可以加減該參數.When color para

30、meter selected,add or reduce this parameter through UP,DOWNG,可以通過FUNTION按鍵選取進入下一模式。Enter next mode through FUNTIONCHANGE WAVE->8|C:00 S:llC:00S:l IH,在此模式下，長按CONFIRM鍵進入保存參數頁面，確認, 下次上電進入當前狀態.In this mode ,press CONFIRM for a long time to enter save parameter page,confirm,enter current pag next time

31、I,功能代號7。. Function code7A.漸變從小地址向大地址方向流水模式，顏色不可更改。Flash from small ID to big ID smooth mode, color is not changeableB.短按CONFIRM無意義.Press CONFIRM for a short time has no meaningC.漸變的時間可以由UP, DOWN鍵選取。Control flash time through UP,DOWND.漸變時間共有16級，其中速度1速度最快。flash time has 16 grades,in which 1 is the fas

32、testE,可以通過FUNTION按鍵選取進入下一模式。Enter next mode through FUNTIONF,在此模式下，長按CONFIRM鍵進入保存參數頁面，確信， 下次上電進入當前狀態.In this mode ,press CONFIRM for a long time to enter save parameter page,confirm,enter current pag next timeG,功能代號8。Function code8A.漸變從大地址向水地址方向流水模式，顏色不可更改。Flash from big ID to small ID smooth mode,c

33、olor is not changeableB. 短按 CONFIRM 無意義.Press CONFIRM for a short time has no meaningC.漸變的時間可以由 UP, DOWN鍵選取。Control flash time through UP,DOWND.漸變時間共有16級，其中速度1速度最快。flash time has16 grades,in which 1 is the fastestE,可以通過FUNTION按鍵選取進入下一模式。Enter next mode through FUNTIONF,在此模式下，長按CONFIRM鍵進入保存參數頁面，確認， 下

34、次上電進入當前狀態.In this mode ,press CONFIRM for a long time to enter save parameter page,confirm,enter current pag next timeG,功能代號9。Function code9A.從小地址到大地址拖尾模式，輸出的顏色可以通過C:后面的 參數修改.默認為00,即七彩色。From small ID to big ID trailing mode,modify output color though parameter after C: default 00,seven colorB.短按CONF

35、IRM鍵可以在顏色和時間上選擇要修改項.C為 顏色,S為顯示時間，口為當前被選取項.Press CONFIRM for a short time to select color and time to beCHANGE DRAG EkC:00S:lCHANGE SPLIT BC:00S:lmodified. C is color,S is time, 口 is the current selected optionC.在時間參數被選取時，跳變的時間可以由UP, DOWN鍵加或 減。When time parameter selected,add or reduce this time thro

36、ugh UP,DOWND.跳變時間共有16級，其中速度1速度最快。strobe time has 16 grades,in which 1 is the fastestE,顏色參數用16進制表示,bit0:紅色,bit1:黃,bit2:綠,bit3:青,bit4: 藍,bit5:紫,bit6:白,bit7:黑.如果該位為1,相應位的顏色被選取，為 0,則該色不輸出.如果為00,則默認七彩色.Color parameter adopts 16 system,bit0red,bit1yellow,bit2 green,bit3 cyan bit4blue,bit5 purple,bit6 whit

37、e,bit7 black.if it is 1,the correspond color is selected.if it is 0,it doesn't output the color.if it is 00,default 7 colorF,在顏色參數被選取時，按UP或DOWN可以加減該參數.When color parameter selected,add or reduce this parameter through UP,DOWNG,可以通過FUNTION按鍵選取進入下一模式。Enter next mode through FUNTIONH,在此模式下，長按CONFIR

38、M鍵進入保存參數頁面，確認， 下次上電進入當前狀態.In this mode ,press CONFIRM for a long time to enter save parameter page,confirm,enter current pag next timeI,功能代號A o . Function codeAA.從中間向兩邊分開模式，輸出的顏色可以通過C:后面的參數 修改.默認為00,即七彩色。Halve mode from middle to sides, modify output color though parameter after C: default 00,seven

39、colorB.短按CONFIRM鍵可以在顏色和時間上選擇要修改項.C為 顏色,S為顯示時間，口為當前被選取項.Press CONFIRM for a short time to select color and time to be modified. C is color,S is time, is the current selected optionC.在時間參數被選取時，跳變的時間可以由UP, DOWN鍵加或減。When time parameter selected,add or reduce this time throughUP,DOWND.跳變時間共有16級，其中速度1速度最快

40、。strobe time has 16 grades,in which 1 is the fastestE,顏色參數用16進制表示,bit0:紅色,bit1:黃,bit2:綠,bit3:青,bit4: 藍,bit5:紫,bit6:白,bit7:黑.如果該位為1,相應位的顏色被選取，為 0,則該色不輸出.如果為00,則默認七彩色.Color parameter adopts 16 system,bit0red,bit1yellow,bit2 green,bit3 cyan bit4blue,bit5 purple,bit6 white,bit7 black.if it is 1,the corr

41、espond color is selected.if it is 0,it doesn't output the color.if it is 00,default 7 colorF,在顏色參數被選取時，按UP或DOWN 可以加減該參數.CHANGE PILE CC:00LS:11CHANGE SOOTTd)H:12K fklK 1: 83When color parameter selected,add or reduce this parameter through UP,DOWNG,可以通過FUNTION按鍵選取進入下一模式。Enter next mode through FU

42、NTIONH,在此模式下，長按CONFIRM鍵進入保存參數頁面，確認， 下次上電進入當前狀態.In this mode ,press CONFIRM for a long time to enter save parameter page,confirm,enter current pag next timeI,功能代號B。 Function codeBA.堆積模式，輸出的顏色可以通過C:后面的參數修改.默認為 00,即白色。 Accumulate mode, modify output color though parameter after C: default 00,whiteB.短按C

43、ONFIRM鍵可以在顏色和時間上選擇要修改項.C為 顏色,S為顯示時間，為當前被選取項.Press CONFIRM for a short time to select color and time to be modified. C is color,S is time, is the current selected optionC.在時間參數被選取時，跳變的時間可以由UP, DOWN鍵加或 減。When time parameter selected,add or reduce this time throuc UP,DOWND.跳變時間共有16級，其中速度1速度最快。strobe ti

44、me has 16 grades,in which 1 is the fastestE,顏色參數用16進制表示,bit0:紅色,bit1:黃,bit2:綠,bit3:青,bit4: 藍,bit5:紫,bit6:白,bit7:黑.如果該位為1,相應位的顏色被選取，為 0,則該色不輸出.如果為00,則默認白色.Color parameter adopts 16 system,bit0red,bit1yellow,bit2 green,bit3 cyan bit4blue,bit5 purple,bit6 white,bit7 black.if it is 1,the correspond colo

45、r is selected.if it is 0,it doesn t output the color.if it is 00,default 7 colorF,在顏色參數被選取時，按UP或DOWN可以加減該參數.When color parameter selected,add or reduce this parameter through UP,DOWNG,可以通過FUNTION按鍵選取進入下一模式。Enter next mode through FUNTIONH,在此模式下，長按CONFIRM鍵進入保存參數頁面，確認， 下次上電進入當前狀態.In this mode ,press C

46、ONFIRM for a long time to enter save parameter page,confirm,enter current pag next timeI,功能代號C。Function codeCA.聲控模式1,紅色的亮度對應12KHZ的頻率分量，綠色的 亮度值對應1KHZ的頻率分量，藍色對應63HZ的頻率分量。Sound control mode1,recfs brightness is 12KHZ,green is 1KHZ,blue is 63KHZ.B. 短按 CONFIRM 無意義.press CONFIRM for a short time has no me

47、aningC.按 UP, DOWN 鍵無意義。Press UP,DOWN has no meanin D,可以通過FUNTION按鍵選取進入下一模式。Enter next mode through FUNTIONE,在此模式下，長按CONFIRM鍵進入保存參數頁面，確認， 下次上電進入當前狀態.In this mode ,press CONFIRM for a long time to enter save parameter page,confirm,enter current pag next timeF,無功能代號。No function codeA.聲控模式2,地址在總地址中的百分比小

48、于12KHz的頻率 分量亮紅色，否則紅色不亮，小于1KHZ的頻率分量亮綠色，否則 綠色不亮，小于63HZ的頻率分量亮藍色，否則藍色不亮。CHANGE S0UNT)(2)H:12K I:1K L:63CHANGE JOIN -DMX- 23E7Z9BCSound control mode2,the percentage of ID is less than color is red,otherwise,it doesn t work.less than 1KHZ,color is green,otherwise it doesn't work.less than 63KHZ,the co

49、lor is blue,otherwise it doesH t work,B. 短按 CONFIRM 無意義.press CONFIRM for a short time has no meaningC,按 UP, DOWN 鍵無意義。Press UP,DOWN has no meanin D,可以通過FUNTION按鍵選取進入下一模式。Enter next mode through FUNTIONE,在此模式下，長按CONFIRM鍵進入保存參數頁面，確認， 下次上電進入當前狀態.In this mode ,press CONFIRM for a long time to enter sav

50、e parameter page,confirm,enter current pag next timeF,無功能代號。No function codeA .程序燈光模式，此模式按編輯的程序執行燈光效果。Program lighting mode,this mode excutes lighting effects according to edition program.B.此模式下內的內容為8個程序步驟的燈光效果代號。In this mode,the context in is 8 program lighting effects codeC.目前燈效代號從1到C。含義見前面的說明。Cur

51、rent lighting effects code is 1 to C.See the above instructionD.燈效包含速度均各模式中定義。Lighting effects containsdefinition in speed.E.短按CONFIRM 鍵可以移動內的光標，按UP或DOWN 鍵可以修改對應的值.press CONFIRM to move cursor in ,press UP,DOWN to modify corresponding valueE,可以通過FUNTION按鍵選取進入下一模式。Enter next mode through FUNTIONF.在此模

52、式下，長按CONFIRM鍵進入保存參數頁面，確定， 下次上電進入當前狀態.In this mode ,press CONFIRM for a long time to enter save parameter page,confirm,enter current pag next timeA.設定燈數目?？稍O定燈數目從1到170from 1 to 170.B. 一個燈代表一個 RGB 下點。One lighting represents one RGB dot.C.可以通過FUNTION按鍵選取進入下一模式。Enter next mode through FUNTIOND.在此模式卜，長按 C

53、ONFIRM 鍵進入保存參數貝聞，確認， 下次上電進入當前狀態。In this mode ,press CONFIRM for a long time to enter save parameter page,confirm,enter current pag next timeA.遙控器快捷鍵設置。 Remote shortcut key set.B .短按CONFIRM,可以更改要修改哪個參數。Press CONFIRM,modify the parameter to be changed.C.按UP或DOWN可以更改選取的值.modify selected value pressing

54、UP,DOWND.可以通過FUNTION按鍵選取進入下一模式。Enter next mode through FUNTIONE.在此模式卜，長按CONFIRM 鍵進入保存參數貝聞，確認， 下次上電進入當前狀態。In this mode ,press CONFIRM for a long time to enter save parameter page,confirm,enter current pag next timeF.F1是遙控器上的按鍵，可以在F1F7之間更改，M是控制器的 變化模式,S是在M變化模式時的時間值，保存后，當按下遙控器 Fn鍵，就會進入M模式，以S時間工作.F1 is

55、the key in remote controller,you can change from F1 to F7.M is the change mode of controller.S is the time value of M change mode,saved,when you press remoter Fn,then enter M mode with 3 time working.A.遙控器的ID設置。為了實現一個遙控器對應一個控制器，所 以遙控器內肩一個8位ID可以設定,每位可設定成0,1,F三個 值.只有遙控器內的ID與這個ID值T時，這個遙控器才1時空 制這個控制器.re

56、mote controller s ID set.To realize one remote controller corresponding to one controller.All remote controller have a 8 digital ID,each digital can set 0,1,F.Remote controller ca control controller only when ID in remote controller is in accordance with this ID.B.短按CONFIRM,可以更改要修改哪個ID。Press CONFIRM to change the ID to be changedC.按UP或DOWN 可以更改選取的值 .Press UP,Down to change selected value.D.可以通過FUNTION按鍵選取進入下一模式。Enter next mode through FUNTIONE.在此模式卜，長按CONFIRM 鍵進入保存參數貝聞，確認， 下次上電進入當前狀態。In this mode ,press CONFIRM for a long