模糊PID控制器的設計及仿真——設計步驟修改

1、-模糊PID控制器的設計與仿真設計模糊PID控制器時，首先要將準確量轉換為模糊量，并且要把轉換后的模糊量映射到模糊控制論域當中，這個過程就是準確量模糊化的過程。模糊化的主要功能就是將輸入量準確值轉換成為一個模糊變量的值，最終形成一個模糊集合。 本次設計系統的準確量包括以下變量：變化量e ，變化量的變化速率ec 還有參數整定過程中的輸出量KP，KD，KI，在設計模糊PID 的過程中，需要將這些準確量轉換成為模糊論域上的模糊值。本系統的誤差與誤差變化率的模糊論域與根本論域?yàn)椋篍=-6,-4,-2,0,2,4,6;Ec=-6,-4,-2,0,2,4,6。模糊PID控制器的設計選用二維模糊控制器。以給

2、定值的偏差e和偏差變化ec為輸入；KP，KD，KI為輸出的自適應模糊PID控制器，見圖1。圖1模糊PID控制器1模糊變量選取 輸入變量E和EC的模糊化將一定圍(根本論域)的輸入變量映射到離散區間(論域)需要先驗知識來確定輸入變量的圍。就本系統而言，設置語言變量取七個，分別為 NB，NM，NS，ZO，PS，PM，PB。(2) 語言變量及隸屬函數根據控制要求，對各個輸入，輸出變量作如下劃定：e，ec論域：-6，-5，-4，-3，-2，-1，0，1，2，3，4，5，6KP，KD，KI論域：-6，-5，-4，-3，-2，-1，0，1，2，3，4，5，6應用模糊合成推理PID參數的整定算法。第k個采樣時

3、間的整定為式中為經典PID控制器的初始參數。設置輸入變量隸屬度函數如圖2所示，輸出變量隸屬度函數如圖3所示。圖2 輸入變量隸屬度函圖3 輸出變量隸屬度函（3） 編輯模糊規則庫根據以上各輸出參數的模糊規則表，可以歸納出49條控制邏輯規則，具體的控制規則如下所示：1. If (e is NB) and (ec is NB) then (kp is NB)(ki is PB)(kd is NS)(1)2. If (e is NB) and (ec is NM) then (kp is NB)(ki is PB)(kd is PS)(1)3. If (e is NB) and (ec is NS) t

4、hen (kp is NM)(ki is PM)(kd is PB)(1)4. If (e is NB) and (ec is ZO) then (kp is NM)(ki is PM)(kd is PB)(1)5. If (e is NB) and (ec is PS) then (kp is NS)(ki is PS)(kd is PB)(1)6. If (e is NB) and (ec is PM) then (kp is ZO)(ki is ZO)(kd is PM)(1)7. If (e is NB) and (ec is PB) then (kp is ZO)(ki is ZO)

5、(kd is NS)(1)8. If (e is NM) and (ec is NB) then (kp is NB)(ki is PB)(kd is NS)(1)9. If (e is NM) and (ec is NM) then (kp is NB)(ki is PB)(kd is PS)(1)10. If (e is NM) and (ec is NS) then (kp is NM)(ki is PM)(kd is PB)(1)11. If (e is NM) and (ec is ZO) then (kp is NS)(ki is PS)(kd is PM)(1)12. If (e

6、 is NM) and (ec is PS) then (kp is NS)(ki is PS)(kd is PM)(1)13. If (e is NM) and (ec is PM) then (kp is ZO)(ki is ZO)(kd is PS)(1)14. If (e is NM) and (ec is PB) then (kp is PS)(ki is ZO)(kd is ZO)(1)15. If (e is NS) and (ec is NB) then (kp is NM)(ki is PB)(kd is ZO)(1)16. If (e is NS) and (ec is N

7、M) then (kp is NM)(ki is PM)(kd is PS)(1)17. If (e is NS) and (ec is NS) then (kp is NM)(ki is PS)(kd is PM)(1)18. If (e is NS) and (ec is ZO) then (kp is NS)(ki is PS)(kd is PM)(1)19. If (e is NS) and (ec is PS) then (kp is ZO)(ki is ZO)(kd is PS)(1)20. If (e is NS) and (ec is PM) then (kp is PS)(k

8、i is NS)(kd is PS)(1)21. If (e is NS) and (ec is PB) then (kp is PS)(ki is NS)(kd is ZO)(1)22. If (e is ZO) and (ec is NB) then (kp is NM)(ki is PM)(kd is ZO)(1)23. If (e is ZO) and (ec is NM) then (kp is NM)(ki is PM)(kd is PS)(1)24. If (e is ZO) and (ec is NS) then (kp is NS)(ki is PS)(kd is PS)(1

9、)25. If (e is ZO) and (ec is ZO) then (kp is ZO)(ki is ZO)(kd is PS)(1)26. If (e is ZO) and (ec is PS) then (kp is PS)(ki is NS)(kd is PS)(1)27. If (e is ZO) and (ec is PM) then (kp is PM)(ki is NM)(kd is PS)(1)28. If (e is ZO) and (ec is PB) then (kp is PM)(ki is NM)(kd is ZO)(1)29. If (e is PS) an

10、d (ec is NB) then (kp is NS)(ki is PM)(kd is ZO)(1)30. If (e is PS) and (ec is NM) then (kp is NS)(ki is PS)(kd is ZO)(1)31. If (e is PS) and (ec is NS) then (kp is ZO)(ki is ZO)(kd is ZO)(1)32. If (e is PS) and (ec is ZO) then (kp is PS)(ki is NS)(kd is ZO)(1)33. If (e is PS) and (ec is PS) then (k

11、p is PS)(ki is NS)(kd is ZO)(1)34. If (e is PS) and (ec is PM) then (kp is PM)(ki is NM)(kd is ZO)(1)35. If (e is PS) and (ec is PB) then (kp is PM)(ki is NB)(kd is ZO)(1)36. If (e is PM) and (ec is NB) then (kp is NS)(ki is ZO)(kd is NB)(1)37. If (e is PM) and (ec is NM) then (kp is ZO)(ki is ZO)(k

12、d is PS)(1)38. If (e is PM) and (ec is NS) then (kp is PS)(ki is NS)(kd is NS)(1)39. If (e is PM) and (ec is ZO) then (kp is PM)(ki is NS)(kd is NS)(1)40. If (e is PM) and (ec is PS) then (kp is PM)(ki is NM)(kd is NS)(1)41. If (e is PM) and (ec is PM) then (kp is PM)(ki is NB)(kd is NS)(1)42. If (e

13、 is PM) and (ec is PB) then (kp is PB)(ki is NB)(kd is NB)(1)43. If (e is PB) and (ec is NB) then (kp is ZO)(ki is ZO)(kd is NB)(1)44. If (e is PB) and (ec is NM) then (kp is ZO)(ki is ZO)(kd is NM)(1)45. If (e is PB) and (ec is NS) then (kp is PM)(ki is NS)(kd is NM)(1)46. If (e is PB) and (ec is Z

14、O) then (kp is PM)(ki is NM)(kd is NM)(1)47. If (e is PB) and (ec is PS) then (kp is PM)(ki is NM)(kd is NS)(1)48. If (e is PB) and (ec is PM) then (kp is PB)(ki is NB)(kd is NS)(1)49. If (e is PB) and (ec is PB) then (kp is PB)(ki is NB)(kd is NB)(1)把這49條控制邏輯規則，鍵入到模糊規則庫中，如圖4。圖4 模糊規則庫5模糊PID控制器仿真利用MA

15、TLAB軟件中的Simulink仿真環境，可以對模糊PID控制器系統進展模擬仿真實驗，來檢驗設計是否到達要求。針對本次控制器設計，我們?cè)O(shè)置被控對象為，根據被控對象，設置相應的PID參數為：=6;=3;=2。圖5為控制器系統在Simulink中的仿真模型。為了方便與傳統PID控制器進展比擬，在Simulink仿真環境中作出傳統PID控制以便于對模糊PID進展比擬。在傳統PID控制器中設置相應的PID參數為：=6;=3;=2。圖6是傳統PID與模糊PID控制器在Simulink中的階躍仿真波形比擬。圖5傳統PID與模糊PID控制器在Simulink中的仿真模型圖6傳統PID與模糊PID控制器在Simulink中的階躍仿真波形比擬圖6中，黃色線為輸入的階躍信號，紫色為輸出的傳統PID控制信號，青色為輸出的模糊PID控制信號，通過圖1-7中傳統PID控制方式與模糊PID控制控制曲線的比照結果可以看出，模糊控制的控制性能要明顯好于傳統的PID控制效果。我們把輸入信號變?yōu)檎?/p>