溫度傳感器DS18B20 外文翻譯

1、DS18B20 Programmable Resolution 1-Wire Digital Thermometer1、DS18B20 FEATURESUnique 1-Wire interface requires only one Port pin for communication, requires no external componentsEach device has a unique 64-bit serial code stored in an onboard ROMCan be powered form data line .Power supply range is 3.

2、0Vto 5.5VMeasures temperatures form -55C to +125C , 0.5C accuracy from -10C to +85 CThermometer resolution is user-selected from 9 to 12 bitsConverts temperature to 12-bit digital word in 750ms (max)Alarm search command identifies and addresses devices whose temperature is outside of programmed limi

3、ts (temperature alarm condition)Available in 8-pin SOIC, and 3-bin TO -92 packages2、DS18B20 BLOCK DIAFRAMFigure 1 shows a block diagram of the DS18B20, The 64-bite ROM stores the devices serial code. The scratchpad memory cont-biyts temperature egister that stores the digital output from the tempera

4、ture sensor. In addition, the scratchpad provides access to the 1-byte upper and lower alarm trigger register (TH and TL), and the 1-byte configuratuion register. The configuration register allows the user to set the resolution of the temperature-to-digital conversion to 9, 10, 11 or 12 bits. The TH

5、,TL and configuration registers are nonvolatile(EEPROM), so they will retain data when the device is powered down.VD1Ll_POMSUPPYSENSEa64-BITEkOM .孫D Eire PortFigure 1 block diagram of the DS18B203、DS18B20 ROM COMMANDSSEARCH ROM 0F0HWhen a system is initially powered up, the master must identify the

6、ROM codes of all slave devices on the bus, which allows the master to determine the number of slaves and their device types. The master learns the ROM codes through a process of elimination that requires the master to perform a Search ROM cycle as many times as necessary to identify all of the -biaR

7、OM? devices.READ ROM 55HThis command can only be used when there is one slave on the bus. It allows the bus master to read the slave64-bit ROM code without using the Search ROM procedure. If this command is used when there is more than one slave present on the bus, a data collision will occur when a

8、ll the slaves attempt to respond at the same time.MATCH ROM 55HThe match ROM command followed by a 64-bit ROM code sequence allows the bus master to address a specific DS18B20 on a multidrop or single-drop bus. Only the DS18B20 that exactly matches the 64-bitROM code sequence will respond to thefunc

9、tion command issued by the master; all other slaves on the bus will wait for a reset pulse.SKIP ROM 0CCHThe master can use this command to address all devices on the bus simultaneously without sending out any ROM code information. Note that the Read Scratchpad command can follow the Skip ROM command

10、 only if there is a single slave device on the bus. In this case time is saved by allowing the master to read from the slave without sending the devices 64-bit ROM code. A Skip ROM command followed by a Read Scratchpad command will cause a data collision on the bus if there is more than one slave si

11、nce multiple devices will attempt to transmit data simultaneously.ALARM SEARCH 0ECHThe operation of this command is identical to the operation of the Search ROM command except that only slaves with a set alarm flag will respond .This command allows the master device to determine if any DS18B20s expe

12、rienced an alarm condition during the most recent temperature conversion .Refer to the OPERATION-ALARM SIGNAING section for an explanation of alarm flag operation.CONVERTT 44HThis command initiates a single temperature conversion. Following the conversion, the resulting thermal data is stored in the

13、 2-bute temperature register in the scratchpad memory and the DS18B20 returns to its low-power idle state. If the device is being used in parasite power mode, within 10us after this command is issued the master must enable a strong pullup on the 1-Wire bus for the duration of the conversion as descr

14、ibed in the POWERING THE DS18320 section. If the DS18B20 is powered by an external supply, the master can issue read time slots after the Convert T command and the DS18B20 will respond by transmitting a 0 while the temperature conversion is in Progress and a 1 when the conversion is done. In parasit

15、e power mode this notification technique cannot be used since the bus1 is pulled high by the strong pullup during the conversion.WRITE SCRACHPAD 4EHThis command allows the master to write 3 bytes of the data to the DS18B20s scratchpad. The first data byte is writer into the TH register , the second

16、byte is written into the TL register, and the third byte is written into the configuration register.Data must be transmitted least significant bit first. All three bytes must be written before the master issues a reset ,or the data may be corrupted.READ SCRACHPAD 0BEHThis command allows the master t

17、o read the contents of the scratchpad .The data transfer starts with the least significant bit of byte 0 and continues through the scratchpad until 9 byte(byte 8-CRC) is read.The master may issue a reset to terminate reading at any time if only partof the scratchpad data is needed.COPY SCRATCHPAD 48

18、HThis command copies the contents of the scratchpad TH,TL and configuration registers to EEPROM. If the device is being used in parasite power mode ,within 10us(max) after this command is issued the master must enable a strong pullup on the 1-Wire bus for at least 10ms as described in the POWERING T

19、HE DS18B20 section.RECALL E2 B8HThis command recalls the alarm trigger values(TH and TL) and configuration data from EEPROM,respectively,in the scratchpad memory .The master device can issue read time slots following the Recall E2 command and the DS18B20 will indicate the status of the recall by tra

20、nsmitting 0 while the recall is in progress and 1 when the recall is done.The recall operation happens automatically at power-up, so valid data is available in the scratchpad as soon as power is applied to the device.DS18B20單總線數字溫度計1、DS18B20的特性獨特的單總線接口只占用一個I/O端口，而無需外圍元件；可以由總線提供電源，電壓適用范圍為3.0V5.5V；測量溫

21、度范圍為-55C+125C，在-10C+85C范圍內精度為0.5C；每個DS18B20含有一個唯一的64位ROM編碼；用戶可以通過編程實現912位的溫度分辨率；分辨率為12時最大轉換時間為750ms；報警搜索命令可識別哪片DS18B20溫度超限；采用3腳T0-92或8腳SOIC封裝。2、DS18B20的內部結構DS18B20的內部結構如圖1所示。主要包括：寄生電源、溫度傳感器、64 位激光ROM和單總線接口、存放中間數據的高速暫存器RAM、用于存儲用戶設定 溫度上下限值的TM和TL觸發器、存儲和控制邏輯、8位循環冗余校驗碼發生器 等。溫度轉換為數的改變時通過改變寄存器的值來實現的，用戶可以根據

22、需要將 DS18B20的溫度轉化位數設置為9,10,11,12位。溫度報警觸發器的設置寄存器 都由非易失性電可擦寫存儲器(EEROM)組成，設置值可以通過相應命令寫入，一 旦寫入后不會因?yàn)榈綦姸鴣G失。3、DS18B20的各個ROM命令（1）Search ROM 0F0H當一個系統初次啟動時，總線控制器可能并不知道單線總線上有多少器件 或它們的64位ROM編碼。搜索ROM命令允許總線控制器用排除法識別總線上的 所有從機的64位編碼。（2）Read ROM 33H這個命令允許總線控制器讀到DS18B20的8位系列編碼、唯一的序列號和 8位CRC碼。只有在總線上存在單只DS18B20的時候才能使用這

23、個命令。如果 總線上有不止一個從機，當所有從機試圖同時傳送信號時就會發生數據沖突。（3）Match ROM 55H這個是匹配ROM命令，后跟64位ROM序列，讓總線控制器在多點總線上定 位一只特定的DS18B20O只有和64位ROM序列完全匹配的DS18B20才能響應隨 后的存儲器操作。所有和64位ROM序列不匹配的從機都將等待復位脈沖。這條 命令在總線上有單個或多個器件時都可以使用。（4）Skip ROM 0CCH這條命令允許總線控制器不用提供64位ROM編碼就使用存儲器操作命令， 在單點總線情況下，可以節約時間。如果總線上不止一個從機，在Skip ROM 命令之后跟著發一條讀命令，由于多個從機同時發送信號?？偩€上就會發生數 據沖突。（5）Alarm Search 0ECH這條命令的流程和Search ROM相同。然而，只有在最近一次測溫