化工機械字典

1、PAGE PAGE 148A阿a阿登生圈Adamson ring阿登生式爐膽Adamson furnace; Adamson type furnace埃aianstrom unit (A)安an安定化shake-down安定到彈性行為 shakedown to elastic action安定狀態 shake-down安培計分流器ammeter shunt壓力容器安全技術監督規程 supervision regulation on safety technology for pressure vessels安全閥safety valve安全閥回座壓力 blow-down for safety

2、valve安全閥接口connections to safety valve安全閥殼casing of safety valve安全閥排放量 discharge capacity of safety valve安全閥排汽管 discharge pipe from safety valve安全閥容量換算 capacity conversion for safety valve安全閥整定壓力 safety valve setting安全規則 rules of safety安全殼 containment vessel安全排放地點safe discharge point安全-破壞空間 safety-fa

3、ilure space安全釋放地點 safe point of discharge安全水平 safe level安全停堆safe shutdown安全溫度范圍 safe temperature limits安全限度safe limits安全泄壓閥safety relief valve安全系數safety factor安全應力范圍 safe range of stress安全運行壽命safe operation life安全裝置safety appliance安全裝置失靈 circumventing of safety device安匝ampere turns安裝mounting安裝隊伍 ere

4、ction staff安裝方法 assembly method安裝靜載荷 erection dead load安裝者的鋼印assemblers stamp氨an氨合成塔ammonia converter鞍an鞍式支座saddle support鞍式支座臥式容器horizontal vessel on saddle support鞍型接管 saddle type nozzle鞍座 saddle鞍座包角contact angle of saddle support鞍座邊角horn of saddle 鞍座反力reaction of saddle鞍座寬度width of saddle support

5、鞍座數目 number of saddle support鞍座位置 location of saddle support鞍座型連接件saddle type fittings按an按規范檢驗 code inspection按規范建造的過程 code construction process暗an暗帶 dark band暗盒 cassette暗紅色dull red凹ao凹槽 recess; groove凹角焊縫concave fillet weld凹口接頭rabbet joint凹面concave side凹凸面法蘭male and female (facing )flange凹凸密封面 male

6、-female seal face凹形concave; dishing凹形爆破片reverse buckling rupture disk凹陷sag奧ao奧氏體不銹鋼austenitic stainless steel奧氏體鋼austenitic steel奧氏體鉻鎳不銹鋼 austenitic chromium-nickel stainless steel奧氏體晶界austenite grain boundaries奧氏體抗蠕變速器鋼austenitic creep-resistant steelANo.成分階段 A-number analysis型掃描 A-scanANSI鋼制管法蘭和附件

7、標準ANSI standard pipe flanges and fittingsASME標志ASME symbolsASME規范技術內容technical aspects of the ASME code.ASME指定人員ASME designeeASTM代號ASTM designationAWS型號AWS classificationB八ba八角墊octagonal ring八字型開裂chevron cracking巴ba巴氏裂紋擴展公式Paris crack growth equation鈀ba鈀屏檢漏儀palladium barrier leak detector靶ba靶板target

8、靶板/底鐵界面target/anvil interface靶板厚度target thickness白bai白點fish-eye白光white light百百分誤差percent error百萬電子伏Mev=million electron volts擺bai擺動焊weave bead welding; welding with weaving擺動焊道 weave bead擺幅oscillation displacement扳ban扳邊的板flanged sheet扳邊開孔flued opening扳緊螺紋用的面wrenching surfaces扳手spanner; wrench扳手面wren

9、ching surfaces扳彎試驗deflection bend test班ban班數number of shift頒ban頒發issuance搬ban搬運handling; carry; transport板ban板邊plate edge; edges of plates板邊偏移plate edge offset板邊缺陷edge imperfections板波plate wave板材的確認plate material validation板材的驗收plate material receipt板材識別號plate identification number板翅式換熱器plate-fin ex

10、changer板的串動和變形plate shifting and warpage板的底角處bottom corner of plate板的兩端both ends of the plate板的位置plate position板和殼 plate and shell板厚中部mid-thickness板殼理論plate and shell theory板坯slab板式換熱器plate heat exchanger(PHE)板條lath板條覆蓋strip covering板條狀馬氏體lath martensite板頭預彎pre-setting of the ends板樁sheet piling半ban半

11、頂角half apex-angle半焊道half-bead半焊道法half bead technique半價層厚度half-value thickness (HVT)(半)徑比radius ratio半精加工semi-finished半經驗基礎semi empirical basis半靠背half coupling半波電流half-wave current (HW)半波整流電流half-wave rectified current半煙煤semibituminous coal半圓形頂板semicircle top sheet半圓形火箱頂板semicircular crown sheet半自動焊s

12、emi-automatic welding半自動弧焊semiautomatic arc welding半自動弧焊機semiautomatic arc welding machine半自動釬焊semiautomatic brazing半鎮靜鋼semi-killed steel半鎮靜狀態semi-killed state半值層厚度half-value thickness (HVT)瓣ban瓣片petal-shaped pieces; petals;curved plate segments棒bang棒材bar; bar stock material棒鋼steel bar棒料bar stock包ba

13、o包復板上的開孔opening in wrapper sheet包角contact angle包晶反應peritectic reaction包括在內inclusive包內真空除氣法ladle degassing包札式容器wrapped vessel包裝packaging包裝標記package marking薄bao薄板sheet薄板坯sheet bar薄壁容器 thin-walled vessel薄壁套管thin-walled sleeve薄壁柱殼thin-wall cylindrical shell薄殼membrane shell薄殼理論membrane shell theory薄殼微體th

14、in-shell elements薄膜力membrane force薄膜應力membrane stress薄膜應力的合力membrane stress resultant薄膜應力分析membrane stress analysis薄膜應力強度membrane stress intensity薄膜應力概念membrane stress concept薄片thin sheet薄片彎曲slice bend薄片狀的lamellar薄弱環節weak link薄藥皮焊條lightly coated electrode飽bao飽和電平saturation level飽和溫度saturation level飽

15、和蒸汽安全閥saturated-steam safety valve飽和蒸汽溫度saturated steam temperature飽和狀態的疏水器saturated drain保bao保持泵holding pump保持塊retainer保護層buffer保護連鎖裝置protective interlocks保護膜 protective film保護氣體shroud gas; shrouding gas; protective atmosphere; cover gas保護涂層protective coating保護裝置secured by guide; guard arrangement保

16、留不予修理left unrepaired保留墊板permanent backing保留在原處left in place保守的conservative保守觀點 conservatism保守主義conservatism保單費用warranty cost保溫insulation;lagging保溫階段holding period保溫期間holding period保溫時間soak time; time at soak temperature; holding times at temperature; time at temperature保溫視鏡thermo-protective sight gl

17、ass保溫溫度soak temperature保險公司insurance company保險式fail-safe manner保險單 Insurance policy報bao報廢率rejection rate報廢原因cause for rejection報價tender保審設計designs for approval暴bao暴露表面exposed surfaces鮑bao鮑辛格效應Bauschinger effect爆bao爆轟產物detonation products爆轟膨脹產物expanding detonation products爆轟速度detonation velocity爆破片bu

18、rsting disk; rupture disk爆破片爆破試驗bursting test of rupture disk爆破片箔材foil of rupture disk爆破片額定泄放流量rated discharge capacity of rupture disk爆破片公稱直徑norminal diameter of rupture disk爆破片夾盤rupture disk holder爆破片坯片blank of rupture disk爆破片起拱工藝和爆破試驗technological doming and bursting test of rupture disk爆破試驗burst

19、 test; bursting test爆破片試驗泄放流量test discharge capacity of rupture disk爆破片泄放直徑discharge diameter of rupture disk爆破片泄壓面積relief area of rupture disk爆破片裝置rupture disk device爆破片最大泄放流量maximum discharge capacity of rupture disk爆破片最小泄放面積minimum net flow area of rupture disk爆破片溫度允差tolerance of bursting tempera

20、ture爆破壓力bursting pressure爆破壓力允差tolerance of bursting pressure爆破元件rupture element 爆炸成形explosive forming爆炸復合板explosively clad plate爆炸復合法explosive cladding爆炸復合連接件explosive clad connections爆炸過渡explosive transfer爆炸焊explosive welding爆炸焊技術explosive welding technique爆炸焊塞子explosively welded plug爆炸焊修理技術explos

21、ive welding repair technique爆炸氣浪blast爆炸塞焊技術explosive plugging爆炸消除應力explosive stress relieving爆炸脹接explosive expansion爆炸滴噴射過渡explosive droplet spray transfer爆破允差bursting tolerance爆破片裝置額定泄放系數rated relieving coefficient of bursting disc device爆破片試樣爆破試驗burst testing of sample bursting disc爆破片裝置額定泄放量rated

22、 relieving capacity of bursting disc device爆破片裝置實際泄放量actual relieving capacity of bursting device爆破片裝置理論泄放量theoretical relieving capacity of bursting disc device爆破片裝置泄放面積relief area of bursting disc device爆破片裝置公稱直徑nominal diameter of bursting disc device爆破片裝置泄放直徑relief diameter of bursting disc devi

23、ce爆破片夾持器bursting disc holder爆破片組件bursting disc assembly杯bei杯-錐狀斷裂面cup-and-cone form fracture surface貝bei貝氏體bainite貝氏體鋼bainite steel貝氏體相變bainitic transformation貝氏體-針狀鐵素體鋼bainitic-acicular ferrite steels貝氏體轉變bainite transformation貝殼狀條紋oyster shell markings背bei背部連接件back connections背反射back reflection背風側

24、leeward side背加壓試驗back pressurizing testing背面back face; root surface背面?zhèn)萻ide evading the wind背面縫隙back crevice背面焊縫back-face weld背面焊接back-face welding背面余高root reinforcement背壓back pressure背壓托架back pressure support被bei被捕集的射流trapped jet被緊密裝配在一起的表面closely fitted surfaces被錄用的焊工approved welders被強烈氧化的表面drossed

25、 surface被攝物襯度subject contrast被攝物對比度subject contrast被授權的代表authorized representative被水濕潤的鍋爐受壓元件water wetted boiler pressure parts被正式授權的官員duly authorized officer倍bei倍尺長度multiple lengths本ben本底background本底信號background signal本體試塊test lug本底熒光background fluorescence本影umbra本票 promissory泵beng泵殼casing of pump迸

26、beng迸裂點pop-in point迸裂現象phenomenon of pop-in比bi比較測量comparative measurements比較讀數comparative reader比較試塊comparative test block比較線圈comparator coils比較系統comparative system比例極限limit of proportionality; proportional limit比例探頭proportioning probe筆bi筆試written examination必bi必須達到的一致性mandatory conformance必要的質量requ

27、isite quality閉bi閉環操作closed loop operation閉環控制closed loop control閉環再現closed loop playback閉路電視closed circuit television(CCTV)閉鎖lock壁bi壁厚wall thickness壁厚變薄wall thinning壁厚中部裂紋midthickness crack壁孔opening in the wall壁溫變化changes in metal temperature邊bian邊角料scrap邊界層boundary layer邊界條件boundary conditions邊線bor

28、derline邊排管bounding row of tubes邊緣穿透裂紋through edge crack邊緣反力boundary reaction邊緣滑移型edge sliding mode邊緣力矩edge moment邊緣區boundary region; boundary zone邊緣缺陷edge defects; edge imperfections邊緣效應edge effect邊緣應力boundary stress邊緣質量marginal quality編bian編碼標志coded marking扁bian扁材flat扁坯slab扁平鋼帶錯繞式容器crossly wound ve

29、ssel by flat ribbon扁平區flatted spot扁塌現象collapse phenomenon變bian變動應力fluctuating stress變動載荷variable loading變壞degradation變截面殼體non-uniform sectional變徑段reducer變量variable變色discoloration變形distortion; deformation變性材料modified material變形測定器tensometer變形層deformed layer變性能理論distortion energy theory變形速度velocity of

30、 deformation標biao標定爆破壓力stamped bursting pressure標定過的流量計calibrated flow meter標定壓力stamped pressure標記鉛筆marking pencil標距gage length標簽tagging標書tender標志mark; denotation標志移植transfer of markings; transfer of marks; mark shift(MS)標準standard; specification; criterion標準參考照片standard reference photographs標準尺寸的容器

31、vessels of standard dimensions標準穿透深度standard depth of penetration標準大氣壓normal atmosphere標準化的補充要求standardized supplementary requirements標準受壓元件standard pressure parts標準測漏孔standard leak標準壓力表master gage標準硬度塊hardness standard block標準正文body of specification標準重力式壓力表檢驗儀standard deadweight tester標準編制組織standar

32、d preparing organization標準草案draft standard表biao表面標定缺口surface calibration notch表面不平整surface irregularities表面層surface coat表面層下缺陷subsurface defects表面鏟傷chipping mark表面粗糙surface asperity表面粗糙度surface roughness表面粗糙度檢查儀surface roughness tester表面鍍層surface coating表面堆焊層surface weld metal buildup表面鈍化surface pas

33、sivation表面多孔性surface porosity表面發暗surface staining表面分層surface lamellation表面割炬gouging blowpipe表面鼓包surface bulging表面光潔度surface roughness; surface finish; surface smoothness表面光潔度檢查儀surface finish indicator表面火焰清理surface scarfing表面積surface area表面檢查surface examination表面精整surface dressing; surface finish表面孔

34、隙度surface porosity表面亮度surface brightness表面裂紋surface crack表面面積surface area表面敏感性surface sensitivity表面膜surface film表面磨傷grinding mark表面能surface energy表面排污surface blow off表面疲勞破壞surface fatigue failure表面波surface wave表面氣孔surface pore; surface blowhole表面氣泡surface blowhole表面清潔度surface cleanliness表面氫化surface

35、hydriding表面清理surface dressing; surface cleaning表面缺陷surface defects; surface imperfections; 表面熱電偶surface thermocouple表面?zhèn)踫urface flaws表面燒剝surface scarfing表面失去光澤surface staining表面撕裂torn surface表面損傷作用surface damage effect表面縮孔surface pipe表面淬硬金屬hard surfaced metal表面填加face feed表面涂層surface coating表面彎曲試驗fac

36、e bend test表面位錯surface dislocation表面溫度surface temperature表面溫度計surface thermometer表面污染surface staining表面修整surface conditioning表面壓印surface indentation表面橢圓形裂紋elliptical surface crack表面硬度surface hardness表面硬化金屬hard surfaced metal表面化應力surface stress表面自由能surface free energy表面張力surface tension表面折疊surface fo

37、lding表面針孔surface pinholes表面枝晶組織 surface dendritic structure表面狀況surface condition; surface appearance表面準備surface preparation表旋塞gage cock表壓力gage pressure表值tabular value表格form表觀surface appearance表列屈服強度值tabulated yield strength表層surface layer表面凹凸不平surface asperity; surface irregularities表達明晰clarity of p

38、resentation表面分析surface analysis表面熱處理surface heat treatment表面凹凸量unevenness of surface表面粗糙度surface roughness并bing并聯開孔補強reinforcement of multi-opening并排的焊縫in-line welds泊bo泊桑比poissons ratio泊蕭流poiseuille flow波bo波動wave motion; fluctuation波幅wave amplitude波高wave height波根外徑root diameter of bellows wave波弧外半徑r

39、adius of outer corrugation波距wave distance波列wave train波利克尼質譜儀bleakney MS波數number of lobes波束擴散beam spread波紋ripple; waviness; corrugation波紋管bellows波紋殼體corrugated shell波形waveform; waveshape; corrugation; rippled波形墊corrugated gasket波形頂部top corrugation波形焊接界面rippled weld interface波形界面rippled interface波形金屬帶

40、crinkled metal ribbon波形爐膽corrugated furnace波形圖oscillogram波陣面wave front波狀界面wavy interface玻bo玻璃glass玻璃板glass plate玻璃板液位計glass plate liquid level gauge玻璃管glass tube玻璃管液位計glass tube liquid level gauge玻璃棉glass wool玻璃水位表water glass; water gage glass玻璃水位表連接法gage glass connection玻璃水位表影象的傳遞transmission of ga

41、ge glass image玻璃狀vitreous玻璃狀熔渣vitreous slag剝bo剝離peeling off; stripping剝離強度peel resistance剝離試驗peel test補bi補償compensation補充addendum; supplement補充材料試驗報告supplementary material test report補充規程supplement rules補充規定additional regulations補充規則supplement rules補充設計規則addition design principles補充試驗supplementary t

42、est補充說明additional remarks補充要求supplementary requirements補充頁supplementary sheet補強reinforcement; reinforcing補強板reinforcing pad補強板-接管連接pad-to-nozzle attachment補強不足under-reinforcement 補強的開孔reinforcement opening補強范圍reinforcement range補強件強度strength of reinforcement補強截面積gross sectional area of reinforcement

43、補強面積area of reinforcement補強面積要求area requirement for reinforcement補強圈補強pad reinforcement補強設計reinforcement design補加鋼印supplementary stamping補脹re-expansion捕bu捕集的射流量amount of trapped jet捕獲capture, trap不bu不按本規范設計的受壓室non-code chambers不扳邊的管板unflanged tubesheet不扳邊的人孔圈unflanged manhole ring不包括腐蝕裕量exclusive of

44、 corrosion allowance不包括襯里厚度thickness exclusive of lining不包括復層厚度thickness exclusive of cladding不包括在內exclusive of 不重合mismatch; non-overlapping不等焊腳unequal leg不等焊腳角焊縫unequal leg fillet weld不斷提供新的服務update service不對稱asymmetry; unsymmetry不對稱的asymmetrical; unsymmetrical不對稱X形坡口 asymmetric double V groove不對稱載

45、荷unsymmetrical loading不對中misalignment不對準misalignment不符合設計形狀departure from design shape不合格的顯示rejectable indications不合理要求illogical requirement不充分的支持insufficient support不加強的圓筒unstiffened cylinder不均勻non-uniform; ununiform; uneven不均勻沉淀ununiform precipitation不均勻加熱uneven heating不均勻冷卻uneven cooling不均勻塑性應變di

46、fferential plastic strain不均勻析出ununiform precipitation不均勻應變differential strains不可得到not available(N/A)不可分式省煤器integral economizer不可焊unweldable不可回變形nonrecoverable deformation不可靠unreliability不可靠系數factor of uncertainty不可逆non-reciprocal不可逆變形nonrecoverable deformation不擴展non-propagating不擴展裂紋non-propagating c

47、rack不連續discontinuity不連續處discontinuity不連續處局部應力discontinuity stress不連續的裂紋群group of disconnected不連續性discontinuity不裂斷準則no-break criterion不另行補強的最大開孔maximum opening diameter of needless reinforcement不另作補強的開孔unreinforced opening不能確定的化學成分uncertain chemical composition不平度irregularities; out-of-flatness不平衡unb

48、alance不平整的表面uneven surface不匹配mismatch; misfit; incompatible不匹配的材料incompatible materials不清晰unsharp不清晰度unsharpness不清晰圖象unsharp image不起皮non-scaling不起皮合金non-scaling alloy不確定uncertain不確定區area of uncertainty不確定性uncertainty不確知uncertainty不確知系數factor of uncertainty不熔化nonconsumable; non-melt不熔化電極nonconsumable

49、 electrode不允許的角接接頭non-permissible corner joint不受壓部件nonpressure parts不受這些限制departure from these limits不水平度out of level不同材料的組合combination of different materials不同的壓力等級different pressure levels不同焊縫金屬dissimilar weld metal不同看法controversial opinion不穩定unstable不穩定奧氏體unstable austenite不穩定電弧unstable arc不穩定流動i

50、nstability of flow不穩定區region of instability不穩定燃燒unstable combustion不穩定性instability不穩定性能unstable properties不穩定型破裂instability type of bursting不穩定運轉unsteady running不穩定狀態non-steady state不穩定組織unstable structure不相干的irrelevant不相關顯示nonrelevant indication不向外供氣no extraction of steam不銹stainless不銹鋼stainless ste

51、el不宣布的隨時復查random unannounced reassessment不一致nonconformity不一致項nonconformities不一致性nonconformity不圓度out of roundness不著火non-inflammable不正常unusual; abnormal不正常操作條件unusual operating conditions不正確incorrect不正確支承incorrect support不證自明的原理first principles不重要unimportant; trivial不重要缺陷trivial faults不作射線照相檢驗no radio

52、graphy不足shortfall布bu布管區最外側outer-tube-limit (OTL)布朗式爐膽brown furnace布氏硬度試驗brinel hardness test步bu步進step; step by step步進電機stepper motor步進馬達stepper motor部bu部分part; component部分夾套partial jackets部分射線探傷的對接焊縫partially radiographed butt welds部分射線探傷的焊接接頭partially radiographed joints部分射線照相檢查partial radiography部

53、分射線探傷partial radiography部分支承板partial support band部件part部件整體釬焊block brazing部位location型掃描B-scanB-A型電離計bayard-alpert lonization gageB-J型質譜儀Bainbridge Jordan MS材cai材料material材料標志marking on material材料標準material specification材料標準號material specification number材料不穩定instability of material材料采購和驗收procurement

54、and receipt of material材料采購科material procurement section材料參數material parameters材料常數material constant材料成本cost of material材料成分material composition材料尺寸scantling材料沖擊試驗impact tests of material材料發放release of material材料剛度material stiffness材料加工特點fabricating characteristics material材料鑒定identification of mate

55、rial材料檢驗inspection of material材料斷裂韌性material fracture toughness材料管理material control材料技術條件material specification材料技術條件號material specification number材料力學mechanics of materials材料明細表material list材料缺陷修補repair of defects in materials材料入庫驗收receipt of material材料識別標記material identification材料識別標記的可追蹤性traceabi

56、lity of material identification材料試驗報告material test report材料試驗合格證material test certificate材料性能material behavior材料性能下降degradation of material properties材料形狀form of material材料選擇material selection材料樣品material sample材料驗收acceptance of material;材料制造廠material manufacturer材料組合materials in combination采cai采購pu

57、rchase采購標準purchasing specifications采購科procurement department采購指南procurement guideline采暖蒸汽鍋爐steam heating boiler采樣sampling彩cai彩頁colored-sheet彩頁增補colored-sheet addenda參can參考consult; reference參考標準reference standard參考點reference point參考斷面reference section參考面reference surface參考試塊reference block參考水平referen

58、ce level參考文獻referenced documents參考線reference line參考線圈reference coil參量parameter參數parameter參照consult; refer to殘can殘留residual; vestige殘留焊劑flux residue殘留試驗液體traces of testing liquid殘留壓縮應力residual compressive stress殘留雜質residual impurity殘品damaged article; Defective goods殘液traces of liquid殘余residue; Residu

59、al殘余奧氏體retained austenite殘余變形residual deformation permanent set殘余硅residual silicon殘余剪應力residual shear stress殘余拉應力 tensile residual stress殘余內應力場residual internal stress field殘余扭矩residual torsion殘余氫residual hydrogen殘余伸長residual elongation殘余彈性應變場residual elastic strain field殘余壓應力compressive residual st

60、ress殘余應變residual strain殘余應力residual stress; remaining stress殘余應力分布residual stress distribution殘余應力模式residual stress pattern殘余應力模型residual stress pattern殘余應力譜residual stress pattern殘余元素含量residual element content殘渣residue倉cngstorehouse; warehouse倉庫storehouse; warehouse; depository倉庫管理員storekeeper; sto