milling machine operate instruction 銑床作業規范

1、1.0 PURPOSE目的Define the milling machine operation instruction.詳細說明銃床操作規范。2.0 SCOPE3.0范圍milling machine operation shall be in accordance with this procedure.臺式銃床操作需依照本規程.4.0 DEPATMENT:涉及部門Tooling department模具部Quality System質量體系COMTENT:內容操作面板介紹PRESET is the main power switch；PRESET為主電源開關；START button

2、for the spindle rotationSTART為主軸旋轉按鈕Work platform lift buttons, UP, DOWN；工作平臺升降按鈕、UP升、DOWN下降EMERGENC；EMERGENCY緊急停止開關；Start and stop the machine機臺的啟動及停上Start and stop the machine: First power off the total electric box at ON. Then turn control switch forward or reverse. Turn control switch to the mid

3、dle of the spindle to stop;機臺的啟動及停止：先將電箱的總電源關至ON,然后將主軸控制開關正轉或反轉，控制開關旋至中 間時主軸停止；Spindle rotation, the steps are as follows主軸頭的旋轉，操作步驟如下The spindle head tilt 主軸頭的左右傾斜Loosen the four nuts evenly, not all release.均勻松開四個螺絲帽，不可全松開Rotating head screw to the required angle. Rotate the right fine-tuning with

4、 a hex nut wrench 旋轉機頭座螺桿至所需要角度，用六角扳手轉動右側微調螺母Balance locking head Nut.將機頭螺帽均衡鎖緊。Correct specification of X-Y axis perpendicular主軸的X、丫方向垂直校正規范：Rotate spindle in the same way, adjusting head nut. Adjusts the main axle and the platform is in vertical.和主軸的旋轉方式相同，調整機頭微調螺母，調至主軸與平臺垂直即可Installation tool chu

5、ck安裝機床夾頭Clean the spindle taper with a rag用抹布清潔主軸錐孔。Align the groove on the spindle chuck machine boss將機床夾頭的凹槽對準主軸凸臺。Rotating Pull screw into screw, locking nut將拉引螺桿旋進夾頭螺孔內，鎖緊螺帽Remove the machine chuck卸下機床夾頭Put spindle on the low speed or use the brakes.將主軸轉速放調在低速檔后開始或使用剎車器Locking nut with a wrench

6、to relax用扳手放松鎖緊螺帽With brass rod or a soft hammer tapping Pull end. Separate the machine BOSS head from taper hole.用軟錘或銅棒敲打拉引螺桿頭端部，使機床夾頭別離錐孔Hand-holding machine chuck, Rotate the top nut, Pull the machine screw, then remove from the chuck用手握持機床夾頭，旋轉頂部螺母，使機床夾頭脫離拉引螺桿后取下5. Attentions考前須知Can not be used

7、equipment without the training.未經培訓合格人員不可動用設備；Convert low-high spindle speed should pay attention to matters.轉換主軸高低檔應該考前須知：When shifts gears of the high low speed should confirm the main axle in the static condition; 高低速換檔時應該確認主軸于靜止?fàn)顟B(tài)；When the spindle in a high class, should Reduce the speed when ge

8、ar shift.當主軸處在高檔，應先調低速度后開始轉換檔；High-speed shifting, the manual spindle micro-switch to combined teeth tooth高低速換檔時，手動微轉主軸，以利齒輪齒合；Not under the spindle rotation in the absence of stalls 不可以使主軸在無檔位下轉動。Notes機臺的操作考前須知：When operating the machine, X、Y axis feed must be uniform, and the head can not be stay on the work piece.操作機臺時，X、Y軸進給一定要均勻，且刀頭不可在工件上停留；Machine spindle is High-precision, whether processing or other reasons are not to be hit 機臺主軸屬于高精度局部，不管加工還是其它原因均不能使其受到撞擊。Failure of the machine should be timely maintenance.機器出現故障應及時維修，嚴禁機臺帶病作業或自行維修；After processing, cle