adc0832數字電壓表(程序+仿真圖).doc

仿真圖：/*包含頭文件*/#include #include /*端口定義*/sbit CS = P35;sbit Clk = P33;sbit DATI = P34;sbit DATO = P34;sbit P20=P20 ;/*定義全局變量*/unsigned char dat = 0x00; /AD值unsigned char count = 0x00; /定時器計數unsigned char CH; /通道變量unsigned char dis = 0x00, 0x00, 0x00; /顯示數值/*共陽LED段碼表*/unsigned char code tab=0xc0,0xf9,0xa4,0xb0,0x99,0x92,0x82,0xf8,0x80,0x90;char code tablewe= 0xfd,0xfb,0xf7,0xef,0xdf,0xfe ;/*函數功能:AD轉換子程序入口參數:CH出口參數:dat*/unsigned char adc0832(unsigned char CH) unsigned char i,test,adval; adval = 0x00; test = 0x00; Clk = 0; /初始化 DATI = 1; _nop_(); CS = 0; _nop_(); Clk = 1; _nop_(); if ( CH = 0x00 ) /通道選擇 Clk = 0; DATI = 1; /通道0的第一位 _nop_(); Clk = 1; _nop_(); Clk = 0; DATI = 0; /通道0的第二位 _nop_(); Clk = 1; _nop_(); else Clk = 0; DATI = 1; /通道1的第一位 _nop_(); Clk = 1; _nop_(); Clk = 0; DATI = 1; /通道1的第二位 _nop_(); Clk = 1; _nop_(); Clk = 0; DATI = 1; for( i = 0;i 8;i+ ) /讀取前8位的值 _nop_(); adval = 1; Clk = 1; _nop_(); Clk = 0; if (DATO) adval |= 0x01; else adval |= 0x00; for (i = 0; i = 1; if (DATO) test |= 0x80; else test |= 0x00; _nop_(); Clk = 1; _nop_(); Clk = 0; if (adval = test) /比較前8位與后8位的值，如果不相同舍去。若一直出現顯示為零，請將該行去掉 dat = test; _nop_(); CS = 1; /釋放ADC0832 DATO = 1; Clk = 1; return dat;/*函數功能:延時子程序入口參數:出口參數:*/void delay(void) int k; for(k=10;k500;k+);/*函數功能:將0-255級換算成0.00-5.00的電壓數值入口參數:i出口參數:*/void convdata(unsigned char i) dis0 = i/51; /個位 dis1 = (i%51)*10/51*2; /小數點后第一位 dis2 = (i%51)*10%51)*10/51*2; /小數點后第二位/*函數功能:數碼管顯示子程序入口參數:出口參數:*/void display(void) P2=0xff; P0=tabdis0 & 0x7f; /顯示個位和小數點delay(); P2=0xfd; P2=0xff; P0=tabdis1; /顯示小數點后第一位delay(); P2=0xfb; P2=0xff; P0=tabdis2; /顯示小數點后第二位delay(); P2=0xf7; P2=0xff; P0=0xff; /顯示小數點后第二位delay(); P2=0xfe; /*函數功能:主程序入口參數:出口參數:*/void main(void) P2=0xff; /端口初始化 P0=0xff; delay(); CH = 0x00; /在這里選擇通道 0x00或0x01 TMOD = 0x01; /設置中斷 TH0=(65536-50000)/256;/定時器1初值定時50msTL0=(65536-50000)%256; IE = 0x82; TR0 = 1; while(1) /主循環 dat = adc0832(CH); convdata(dat); /數據轉換 display(); /顯示數值 /*函數功能:定時器中斷延時程序 這一段的作用時隔一段時間抽樣一次 否側顯示的最后一位會不穩定入口參數:出口參數:*/void timer0(void) interrupt 1 TMOD = 0x01; TH0=(65536-50000)/256;/定時器1初值