采購技術條件-鋼板516(中英文對照)

1、HGPURCHASE SPECIFICATION采購技術條件DOC. NO. UD2-08U1-1REV. 0PAGE 1 OF 5PURCHASE SPECIFICATIONFOR CARBON STEEL PLATES. SA-516MGr.485SA-516MGr.485鋼板采購技術條件JOB NO. 08U1DRAWING NO.: U-08-1/Rev.00REV.DATEDESCRIPTIONDESIGNED BYAPPROVED BYHONGGUANG CHEMICAL EQUIPMENT Co.,Ltd.HGPURCHASE SPECIFICATION采購技術條件DOC. NO

2、. UD2-08U1-1REV. 0PAGE 2 OF 5This specification is provided description for purchasing material.本技術條件對采購下列材料進行了規定.1. Dimension: mm piece 尺寸 件 2. Name of material: 材料名稱 Pressure vessel plates carbon for moderate-and lower- temperature service. 中、低溫壓力容器用碳鋼板3. Specification designation 材料牌號 ASME Code S

3、ect. II 2007Ed, SA-516MGr.4854. Supply condition and dimensional tolerance 供貨狀態和尺寸公差 Supply condition: hot-rolled 供貨狀態：熱軋NO.THICKNESS mm厚度PERMISSIBLE VARIATIONIN THICKNESS mm厚度允許偏差REMARKS備注128+1.1+0.25 5. Manufacture 制造The plate shall be killed and shall conform to the fine austenitic grain size req

4、uirement .鋼板應為鎮靜鋼，并應符合細奧氏體精粒度的要求。6. Chemical requirements 化學成分 An analysis of each heat shall conform to the chemical requirements shown in the following table: 鋼的熔煉分析化學成分應符合下表的規定。Elements元素Heat analysiscomposition. 熔煉分析成分Carbon, max 碳的最大含量Manganese錳的含量Phosphorus, max.磷的最大含量Sulfur, max.硫的最大含量Silicon

5、硅的含量0.280.85-1.200.0350.0350.15-0.40Unspecified elements on heat analysis shall conform to the chemical requirements shown in the following table (SA-20, Table 1): 熔煉分析未規定的元素應符合下表的規定（(SA-20, 表 1)：HGPURCHASE SPECIFICATIONDOC. NO. UD2-08U1-1REV. 0PAGE 3 OF 5Elements元素Heat analysiscomposition. 熔煉分析成分Co

6、pper, max.銅的最大含量Nickel, max. 鎳的最大含量Chromium, max. 鉻的最大含量Molybdenum, max.鉬的最大含量Vanadium, max.釩的最大含量 Columbium, max.鈮的最大含量Titanium, max.鈦的最大含量0.400.400.300.120.030.020.03Note: A. The sum of copper, nickel, chromium and molybdenum shall not exceed 1.00% on heat analysis. Cu、Ni、Cr及Mo含量總和不應超過1.00（熔煉分析）。B

7、. The sum of chromium and molybdenum shall not exceed 0.32% on heat analysis. Cr、Mo元素含量總和不應超過0.32（熔煉分析）。7. Mechanical requirements力學性能要求 7.1 Tension test requirement-The material as represented by the tension specimen shall conform to the requirements prescribed in following table: 拉伸試驗要求鋼板的拉伸試驗性能應符

8、合下表要求：Tensile strength, Mpa 抗拉強度Yield strength, min. Mpa 屈服強度Elongation in 50 mm min. % 伸長率，標矩50mmor Elongation in 200mm min. % 伸長率，標矩200mm48562026021177.2 Impact test (charpy V-notch): Not required沖擊試驗（夏比V型缺口）：不要求8. Supplementary requirements: None附加要求：無9. Nondestructive examination: Not required無損

9、檢測：不要求10. Repair by welding補焊Repair welding shall not be permitted.不允許補焊HGPURCHASE SPECIFICATIONDOC. NO. UD2-08U1-1REV. 0PAGE 4 OF 511. Material test report材料試驗報告 The material test report shall be furnished to XXXX in Chinese- English bilingual format and in SI units.材料試驗報告應以中英文兩種語言和SI單位制的格式提供給HG. T

10、he following items shall be reported: 報告中應包括下列內容：11.1 Applicable code : ASME Code Sect. II 2007Ed 適用規范：ASME Code Sect. II 2007Ed 11.2 Material designation: SA-516M Gr.485 材料牌號：SA-516M Gr.48511.3 Heat number and batch number and nominal plate thickness and size 熔煉爐號、批號及鋼板的名義厚度和規格11.4 Chemical analysi

11、s results including unspecified elements 化學分析結果包括未規定元素11.5 Mechanical test results 力學性能試驗結果11.6 Condition of supply: hotrolled 供貨狀態：熱軋11.7 Austenitic Grain Size : Austenitic Grain Size shall be not less than 5 size on cementation process or The total aluminum shall be not less than 0.020% on heat an

12、alysis or 0.015 on acid-soluble aluminum. 奧氏體晶粒度：用滲碳法測量所得的奧氏體晶粒度應為5號及5號以上或熔煉分析中總鋁含量不低于0.020或酸溶鋁含量不低于0.015。12. Identification of plates鋼板的標識 Identified marking shall be legibly steel die stamped and stenciled on each finished plate in two places not less than 300 mm from the edges with the following

13、data: 應該在已完成的鋼板距邊緣300mm的兩處清楚的模印或鋼印上如下數據：12.1 Manufacturers name or trade mark 制造廠的名稱或商標12.2 Heat number and Plate identifier. 爐號和鋼板的識別符12.3 Specification number and grade. (SA-516MGr.485) 規范編號和材料等級. (SA-516MGr.485)12.4 Dimension (TWL) 尺寸(TWL)13. Packing, marking and loading for shipment包裝、標記和裝運HGPURCHASE SPECIFICATIONDOC. NO. UD2-08U1-1REV. 0PAGE 5 OF 5Packing, marking and loading for shipment shall be in accordance with the ASTM spec