可充電型真空吸塵器電池排氣測試

1、真空吸塵器電池排氣測試（可充電型）修訂日期修訂單號修訂內容摘要頁次版次修訂審核批準2011/03/30/系統文件新制定2A/0/批準:審核:編制:真空吸塵器電池排氣測試（可充電型）1.0Purp ose /目的To evaluate the safety of battery pack empioyed in therechargeable type sample whe n term in als of battery p ack areshort-circuited.評估可充電型樣機的電池是否符合安全要求2.0Defini tio n/ 概念:2.1Discharge-Op erate t

2、he sample no Ion ger to op erate with theswitch in the ” on” position for an additional hour.電池完全放電-運行樣機直到其完全停止，再保持開關處在開的位2.2置上多一個小時.Recharge-Charge the discharged sample for 16 hours throughthe charger conn ected to a supply main of 120V/60Hz.充電-讓電池完全放電的樣機通過充電器接上120V/60HZ電源充電16小時.3.0 Reference Docu

3、ments/ 參考文獻 :ULS-01017-DMLW-DataSheet-2001 Form Issued: 1992-07-01 FormRevised: 2006-07-074.0Equipment/ 設備 :4.1Frequency Converter.變頻電源4.2Nonconductive oil and test box.絕緣油和測試容器4.3Digtal multimeter.萬用表4.4Knife switch閘刀開發5.0General Instructions/講明:5.1Tests may be conducted at any ambient temperature

4、within arange of 10-40 C (50-100 F).測試可在1040C (50100 F )之內的環境溫度下進行.5.2 Unless otherwise noted, all tests are to be conducted withappliance connected to a 120VAC, 60Hz power source.除非另外標注 , 否則所有樣機都將連接在 120V/60Hz 電源下進行測試.5.3All equipment used must be calibrated on an annual basis.Calibration stickers

5、with last calibration and calibrationdue date must be affixed to each instrument.使用的所有設備都必須以一年為周期進行調校 . 載有最后調校日期和調校周期的調校粘紙必須被粘固在每一個儀表上6.0Procedure/ 步驟 :6.1Obtain a representative sample of the appliance to be tested.預備一臺有代表性的樣機用來測試6.2Obtain Test Results Form TTR1033 and completely fill in theinforma

6、tion describing the sample and the equipmentused6.36.4prior to running the test.用TTR1033吉果的表格，在測試運作前完整地填入樣機和使用的設備的情況 .Discharge and recharge the sample.將樣機電池完全放電后充滿電 .Short-circuit the terminals of battery pack through knifeswitch making sure it open.把樣機電池包兩極端子分不引一條線出來接到一開關裝置操縱的兩側，確保開關裝置處于斷開狀態。6.5 I

7、mmerse the sample completely into nonconductive oil.將樣機完全浸入裝滿油的容器中。如圖 1 示意圖。6.6 Close the knife switch until the ultimate results are obtained.合上開關裝置，觀看測試現象，直到最終結果出現，停止測試6.7As a result of the testa) There is/is no venting of the battery b) There is no rupturing or distortion of the battery case;c) T

8、here is no expulsion of the battery electrolyte.觀看測試中是否有冒泡，測試后電池殼是否斷裂或變形，電池電極是否脫位。7.0Results/ 結果 :7.17.2Use the corresponding Test Results Form TTR1032to report allnumerical results as the information described below.使用TTR1032測試結果的表格,除報告所有數字結果外，還有下列描述的數據 .Clearly and completely describe all parts that are part ofthis evaluation. Include all model numbers, manufacturing date codes, materials, p lastic part revisio n letters, and modificati on status.清晰并完整地描述本評估的所有零件，包括所有型號名稱，材料和塑料零件改版符號7.3 Clearly and completely describe all special conditionsof thetest (i.e. Was the test