JRCJAX-9A氣象傳真機的操作規程

1、JRC/JAX-9A氣象傳真機的操作規程氣象傳真機的操作規程TYPE：JRC/JAX-9A一接收頻率的設定。For example, a frequency of 7305 kHz of the JMH can be set as follows:例如, JMH 臺的 7305 kHz 的頻率可以按下列方法設定1.Press POWER switch on the rear.3.將傳真機背面上的POWER 開關打到ON 的位置。2.PressPressCLRbutton.CLR按鈕。0 key.按數字鍵二接收頻率的登記。(1)Registering reception frequencies

2、for automatic frequency selection (Ex. 1)This example registers JMH frequencies to channel group 00.為自動頻率選擇而登記接收頻率（例 1）。該例將 JMH 的頻率登記到 00 組。1.PressPOWER switch on the rear.將傳真機背面上的POWER開關打到ON 的位置。2.PressCLR button.CLR 按鈕。3.Pressnumeric keys to enter a frequency of 3622.5kHz.5.Press按數字鍵4.PressENT按數字鍵

3、6.來輸入頻率 3622.5 kHzENT button.按鈕。numeric keys to enter a frequency of 7305.0kHz.9 來輸入頻率 7305.0 kHz.PressENT button.7.按 ENT 按鈕。Repeat the above steps 3 to 6 to register the remaining frequencies.8.Press重復上述 3ENT ENTENT ENT到 6 的步驟來登記剩下的頻率。ENT button to leave channel 07 08 09 unregistered.ENT 按鈕使 07 08

4、09 頻道不登記。2) Registering reception frequencies for automatic frequency selection (Ex.2)This example register JMH frequencies to channel group 30.為自動頻率選擇而登記接收頻率（例 2）。該例將 JMH 的頻率到 30 組1Press POWER switch on the rear.2將傳真機背面上的 POWER 開關打到 ON 的位置Press CLR button. To clear the data on the LCD.按 CLR 按鈕來清除液晶

5、屏上的數據。Press numeric keys 09 to enter a frequency of 3622.5kHz.4按數字鍵 0Press CH button9 來輸入頻率 3622.5kHzto set the channel set mode.按 CH 按鈕來設置頻道方式。5Press numeric keys3 and 1in this order to enter the channel number 31.按數字鍵 3 和 1 來輸入頻道號碼 316Press ENT button to register the entered frequency to channel 3

6、1.按 ENT 按鈕把輸入的頻率登記到 31 頻道。7 Press numeric key 09 to enter a frequency of 7305.0kHz.8Press按數字鍵 09 來登記頻率 7305.0kHzENT button to register the entered frequency to channel 32.按 ENT 按鈕把輸入的頻率登記到 32 頻道。9Repeat the above steps2 to 6 to register the remaining frequencies.重復上述 2 到 6 步 登記剩下的頻率。10 PressENTENTEN

7、T button to leave channel 37,38,39 unregistered.按 ENT ENTENT 按鈕使 37,38,39 頻道不登記(3) Registering receiving frequencies when the Automatic Frequency Selection function is notUsed (Ex.1).The method of registering receiving frequency without need for the use of the CH button.3.2.Press numeric keys按數字鍵4.P

8、ress不使用自動頻率選擇功能時，接收頻率的登記不使用 CH1.Press將傳真機背面上的PressENTCLRCLR例 1）按鈕進行登記接收頻率的方法。POWER switch on the rear.POWER開關打到ON的位置。button to clear the data on the按鈕來清除 LCD 上的數據。LCD.2 2 and 5 to enter a frequency of 3622.5kHz.2 和 5 來輸入 3622.5kHz 的頻率。button to register the entered frequency to channel 01.按 ENT 按鈕把輸

9、入的頻率登記到 01 頻道。重復上述第 3 和第 4 步驟， 使頻道號碼自動增加。(4)CHRegistering reception frequencies When the Automatic Frequency Selection function is not used (Ex.2).The method of registering receiving frequency with need for the use of theButton.不使用自動頻率選擇功能時，接收頻率的登記。使用 CH 按鈕來登記接收頻率的方法。1. Press POWER switch on the rea

10、r.將傳真機背面上的 POWER開關打到ON 的位置2.PressCLR按CLR3.Press numeric keys0按數字鍵 0-4.PressCH按CH5.Press numeric keys按數字鍵3button to clear the data on the LCD.按鈕來清除屏上的數據。- 9to enter a frequency of 3622.5kHz.9 來輸入頻率 3622.5kHz 。: 9 e1 p5 I) Y( |3 v8 s1 8 j#button to set the Channel Set mode.: E2 P9 Z) e$ v, U3 z按鈕來設置頻道

11、設置方式。3 1to enter the channel number 31.1 來輸入頻道號碼 31。6.Press ENT button to register the entered frequency to the channel 31.按 ENT 按鈕把輸入的頻率登記到 31 頻道。7.Press numeric keys0按數字鍵 0 -8.Press CH按 CH9 Press numeric keys4按數字鍵- 9 to enter a frequency of 7305.0kHz.9 來輸入頻率 7305.0kHz 。button to set the Channel Se

12、t Mode.# O! P2 V3 e9 o: E) S+ M# E按鈕來設置頻道設置方式。1to enter the channel number.% z. u$ R0 K1 |- m) , q4 1 來輸入頻道號碼。10. Press ENT button to register the entered frequency to channel 41.按 ENT 按鈕把輸入的頻率登記到 41 頻道。11. Repeat the above steps 7 and 8 to register another frequency to the next channel.重復上述第 7 和第 8

13、 步驟把另一頻率登記到下一個頻道。三調出已登記的頻率。1)Calling a registered frequency when the Automatic Frequency Selection function is used.This examplecalls one of JMH frequency stored in memory.1.Press POWER switch on the rear.將傳真機背面上的 POWER 開關打到 ON 的位置2.PressMO button to set the memory out mode.按 MO 按鈕來設置儲存器輸出方式。3. Pres

14、s numeric keys 0 0in this order to call the group channel 00.The frequencies belonging to the channel group 00 are displayed in sequence from the beginning.按數字鍵 0 0 來調出 00 頻道組。屬于 00 頻道組的頻率從開始按序被顯示。 ) x/ |7 x7 o& A; v% zCalling a registered frequency when the Automatic Frequency Selection functionis

15、not used . This examplecalls a frequency channel 01.1Press不使用自動頻率選擇功能時，調出已登記的頻率。該例調出 01 頻道的頻率。POWER switch on the rear.將傳真機背面上的POWER 開關打到 ON 的位置2 PressMO button to set the memory out mode.3. Press numeric keys0 and 1in this order to call the frequency channel 01.按數字鍵 0 和 1 來調出 01 頻道的頻率。4 Repeat the

16、above step 3 to call the registered frequencies in sequence.重復上述第 3 步按順序調出所登記的頻率。四傳真接收方式的設定。（ 一）.自動接收方式的設置。In this mode, the JAX-9A automatically receives facsimile broadcasting signals on a selected channel. Take steps below toset the AUTO reception mode.AUTO 接收方式。用這種方式， JAX-9A 傳真機自動在被選擇的頻道上接收傳真信號。

17、采用下列步驟來設置1.Press POWERswitch on the rear.按傳真機背面上的 POWER 開關打到 ON 的位置2.PressMO CLR button and numeric keys9 to set the reception frequency.3. Press按 MO CLR 按鈕和數字鍵 09 來設置接收頻率。MAN button to change the reception modefromMANUto AUTO(When “MAN”U is displayedon the top of the first line of the LCD).MANU 按鈕把

18、接收方式從人工轉到自動方式當“ MANU” 顯示在屏上第一行時）4. With this step, the AUTO receiving mode is set.Whenreceivinga STARTsignal, the JAX-9A automaticallysets the IOC and the scanning speed, matchesphases and starts to record the facsimile signal.When receiving a STOP signal, the JAX-9A stops recording, feeds the paper

19、 to the cutter position,and stops.To stop recording halfway, press the MANU button twice.“Waiting start signal ” appears signal and start recording again.on the LCD. Whenyou press theMANUbutton once, theMANUreceiving modeis set. The JAX-9A detects a similarity到了這一步， 就設置好了自動接收方式。當收到啟動信號時，傳真機自動設置 IOC

20、和掃描速度，匹配相位并開始記錄傳真信號。當收到停止信號時，傳真機停止記錄，把記錄紙送到切割器并停止。中途要停止記錄，按 MANU 按鈕兩次, “Waiting start signal” 出現在熒光屏上。當按 MANU 按鈕一次， 人工接收方式被設置。傳真機檢測到類似的信號并重新記錄。z/ I h: h% W6 c# y5 c二）人工接收方式的設置程序1. PressPOWER switch on the rear.將傳真機背面上的POWER 開關打到ON 的位置上。2. Press MAN button to change the reception mode from AUTO to MA

21、NU (When “WAITS FOR START SIGNALis displayedon the top of the first line of the LCD). When thisMAN button is pressed, the MANU reception mode is set .MAN 按鈕把接收方式從自動改到手動（當WAITS FORSTARTSIGNAL” 顯示在屏上第一行時）。當按下MAN 按鈕時，人工接收方式被設置。3.Select a scanning density (288 or 576) by pressing theIOCbutton. 288 and 5

22、76 appears alternately each timethe IOC button is pressed.通過按IOC 按鈕來選擇掃描密度（ 288 或 576）IOC 按鈕每按一次 288 和 576 將交替出現。4.Select a scanning speed (60, 90,120 or 240) by pressing theSCAN button. The scanning speed changes in the orderof 60, 90, 120 and 240 each time theSCAN button is pressed.通過按SCAN 按鈕來選擇掃描

23、速度（ 60， 90， 120 或 240）SCAN按鈕每被按一次，掃描速度就按 60，90， 120 和 240依次改變一次。or:MO CLR button and numeric5. Set a reception frequency by pressingkeysSet a reception frequency by calling a group channel (for automatic frequency selection), by calling afrequency channel.This example calls a group channel.通過按MOCLR

24、按鈕和數字鍵9 來設置接收頻率或：6.通過調出頻道組（為自動頻率選擇），或調出頻道來設置接收頻率。With this step, the JAX-9A is ready for MANU receiving.Whenreceivinga STARTsignal or a similarity signal in this status, the JAX-9A startsto record the facsimilesignal.When receiving a STOP signal, the JAX-9A stops recording.To recording halfway, pres

25、s theMAN button once.“Waiting start signalappears on the LCD.到了這一步，傳真機為人工接收做好了準備。在這種狀態下，當收到啟動信號或類似的信號時，傳真機開始記錄傳真信號。當收到停止信號時，傳真機停止記錄。中途要停止記錄，按MAN 按鈕一次。 屏上出現“Waiting start signal三）強制記錄操作的設置1.Press # andMANbutton in this order. The JAX-9A starts recording and show#REC” on the LCD. (In this case, phase

26、matching has not been completed.)2.MAN 按鈕，傳真機開始記錄并在熒屏上顯示Press the#REC”FEED button and check where the在這種情況下，相位匹配還沒有完成。phase signal (or similarity signal)is recorded.Use the scale having divisions 1 to 31 to read the position.FEED 按鈕并檢查相位信號（或類似信號）是否有記錄。（使用1到31的刻度來讀出相位的位置。3.Press thePH button.PH 按鈕。4.

27、Enter the phase signal recording position (scale value) in thePH” entry field.For example,the phase signal is recorded on scale division 23, press 2 and 3 in this order.在“PH輸入?yún)^(qū)輸入相位信號所在的位置（刻度值）。5.PressENT button. Phase matching is completed andPH=” disappears.按 ENT按鈕，相位匹配被完成PH=” 消失。To stop recording,

28、 press theandRECbuttons again in this order.要停止記錄， 按順序再按REC 按鈕。( 三).定時接收方式1.時間的設定2).Press1).PressPOWER將傳真機背面上的 POWERCLOCK button. The present time appears onswitch on the rear.開關打到ON 的位置。the LCD. The time is always represented in the 24-hour system.按 CLOCK 按鈕?，F(xiàn)在的時間出現在熒屏上。時間總是按 24 小時制表示。3).Enter a ti

29、me later than the present time by entering a value in an underlined column by numeric keys 0用數字鍵9 在有下畫線的欄內輸入比現在的時間稍早一點的時間。Press ENT button immediately when your standard time tells the entered time. the built-in timerstarts.當時間到了你輸入的時間時立即按ENT 按鈕，內部的計時開始。5).Press CLOCK button to reset the Time Set Mo

30、de. The AUTO or MANU reception mode returns.按 CLOCK 按鈕使時間設置方式復位，變成自動或人工接收方式。2.定時接收方式的設置1).PressPOWER switch on the rear.2).將傳真機背面上的POWEF開關打到ON 的位置。Press MAN button to change the reception mode from MANU to AUTO (when the MANU mode is set).按 MAN 按鈕把人工接收方式改成自動方式（當傳真機被設置為人工方式時）。3).PressPROG button to s

31、et the program mode.PROG 按鈕以設置編程方式。Press numeric keyto enter a program channel. TheCH=1” appears on the LCD.5).PressENT按數字鍵1 以輸入程序的頻道?！癈H=1出現在熒屏上。button to register the entered channel and the underline moves to the next entry column (Start timeentry).按 ENT按鈕以登記所輸入的頻道并且下劃線移動到下一欄（啟動時間欄）。7).Press6).EN

32、TPress numeric keys按數字鍵9(such as 12:05) to set the start time 12:05.如 12：05）來設置啟動時間 12： 05。button to register the entered start time and the underline moves to the next entry column (StopTime entry).按 ENT 按鈕以登記所輸入的啟動時間并且下劃線移動到下一欄（停止時間欄）。8).Press numeric keys9(such as 12:30) to set the stop time 12： 30 .9).Press按數字鍵ENT button to register如 12： 30）來設置停止時間 12： 30。the entered stop time and the underline moves to the next entry column