ISO140012015廢氣監測管理程序英文版

1、AIR EMISSION CONTROLQKW-666-EMS0013/AAPage: 1of 4 Date: 99-10-061. Contents1. Con te nts2. Scope and applicatio n3. In troduct ion4. Definitions and abbreviations5. Resp on sibilities6. Procedures7. In teract ing Procedure8. Support ing form9. Flow Chart of Procedure10. Appe ndix2. Scope and applica

2、tionThis procedure serves to define and monitor the quality of air emission . This procedure is applicable to Shen zhe n Factory only.3. IntroductionIn order to avoid air polluti on, air emitted to the atmosphere must be con trolled within a pre-determined condition. This procedure is a guide line f

3、or air emission monitoring.4. Definitions and AbbreviationsPTEPla nt Engin eeri ng Sectio n of Maintenance Engin eeri ng Departme nt.EMSEn vir onmen tal Man ageme nt System.EIRFEn vir onmen tal In cide nt Registrati on Form5. ResponsibilitiesPTE mecha nic - Perform the regular check ing.PTE Engin ee

4、r - Main tai n and Mon itor the system and make sure the air emissi on is un der con trolled.EMS officer - Follow up in cide nt of air emissi on.6. Procedures6.1 PTE mecha nic visual check power gen erator exhaust vapor and record dow n the result every week.6.2 Mon itori ng method.Use the in specti

5、 on Film to compare the content of the exhaust vapor see if it is with in the acceptance limit and record down the result and other data.AIR EMISSION CONTROLQKW-666-EMS0013/AAPage: 2of 4 Date: 99-10-066.3 Emerge ncy Pla n6.3.1 System failure.If the test result is over-5)：GPTE mecl(3 nic shall inform

6、 the servicepeople to repair the system at once. He shall fill in the EIRF and submit the completed form to EMS officer. The EMS officer shall follow up the case accordi ng to the procedure QKW-666-EMS0003 and QKW-666-EMS0004.6.3.2 When the problem occurred in sect ion 6.3.1 cannot be fixed within f

7、our hours and PTE mechanic shall inform PTE Supervisor or his superior and the service people to arrange the machi ne supplier to come for the system urge nt repair.6.3.3 As service people cannot repair or arrange the supplier to repair the machine withi n one day, it is n ecessary to stop the mach

8、ine for no rmal use and use the machine only for backup with close monitoring until problem fixed.6.3.4 In case of sect ion 6.3.1, if the test result is over Gray 5 ' it is neto use the machine until the problem fixed since the environment is serious affected.6.4 Exhaust Vapour Content Measureme

9、 nt6. 4.1 The content should be measured once per year in order to make sure the machine is un der good con diti on and avoid air pollutio n.7. Interacting ProceduresQKW-666-EMS0003En viro nmental In cide nt Registratio n ProcedureQKW-666-EMS0004 Corrective and Preve ntive Actio n Procedure - EMS8.

10、Supporting FormsQKW-666-EMS0013 Air Emissio n Con trol Form 19. Flow ChartN.A.AIR EMISSION CONTROL FORM 1AIR EMISSION CONTROLQKW-666-EMS0013/AA Page: 3of4Date: 99-10-06Date / TimeResultDone ByRemarkSupplementary RecordWeek :PTE Supervisor : Date : QKW-666-EMS0013 FORM 1 AA10. Appendix - Chinese translation of point 6.1 to 6.3AIR EMISSION CONTROLQKW-666-EMS0013/AAPage: 4of 4 Date: 99-10-06空氣排放限制的程序：6.1 廠房維修人員必須每星期測試發電機空氣排放及記 錄所有結果,6.2 監察方法：使用檢查膠片監察黑煙排放是否在限制范圍內.6.3 緊急安排6.3.1系統問題當空氣排放濃度大于“灰度2灰度3 - 5以上時,廠房維修人員必須立即通知維修人員進行維修,同時要填寫一份EIRF表格交EMS主任,當EMS主任收到表格後必須跟進及根據 QKW-