配置手工負載分擔模式鏈路聚合

1、企業案例計算機網絡系統集成項目（工程項目案例及實踐）所在系別： 計算機技術系 所屬專業： 計算機網絡技術 指導教師: 張海峰 專業負責人： 孫志成 配置手工負載分擔模式鏈路聚合一、組網需求如圖1所示，Switch和SwitchA之間用Eth-Trunk鏈路連接。要求Switch和SwitchA之間的鏈路有較高的可靠性。圖1 配置手工負載分擔模式鏈路聚合組網圖 二、配置思路采用如下的思路配置負載分擔鏈路聚合：1. 創建Eth-Trunk。2. 加入成員接口。三、數據準備為完成此配置例，需準備的數據：· 鏈路聚合組編號。· Eth-Trunk的成員接口類型和

2、編號。四、操作步驟1. 創建Eth-Trunk# 創建Eth-Trunk 1。<Quidway> system-viewQuidway sysname SwitchSwitch interface eth-trunk 1Switch-Eth-Trunk1 quit2. 向Eth-Trunk中加入成員接口# 將Eth0/0/3加入Eth-Trunk 1。Switch interface ethernet 0/0/3Switch-Ethernet0/0/3 eth-trunk 1Switch-Ethernet0/0/3 quit# 將Eth0/0/4加入Eth-Trunk 1。Swit

3、ch interface ethernet 0/0/4Switch-Ethernet0/0/4 eth-trunk 1Switch-Ethernet0/0/4 quit3. 配置Eth-Trunk 1# 配置Eth-Trunk 1允許VLAN100-200的報文通過。Switch interface eth-trunk 1Switch-Eth-Trunk1 port link-type trunkSwitch-Eth-Trunk1 port trunk allow-pass vlan 100 to 200Switch-Eth-Trunk1 quit4. 驗證配置結果在任意視圖下執行displa

4、y trunkmembership命令，檢查Eth-Trunk 1是否創建成功，及成員接口是否正確加入。Switch display trunkmembership eth-trunk 1Trunk ID: 1used status: VALIDTYPE: ethernetWorking Mode : NormalNumber Of Ports in Trunk = 2Number Of UP Ports in Trunk = 2operate status: upInterface Ethernet0/0/3, valid, operate up, weight=1,Interface Et

5、hernet0/0/4, valid, operate up, weight=1,# 顯示Eth-Trunk 1的配置信息。Switch display eth-trunk 1Eth-Trunk1's state information is: WorkingMode: NORMAL Hash arithmetic: According to SA-XOR-DA Least Active-linknumber: 1 Max Bandwidth-affected-linknumber: 8Operate status: up Number Of Up Port In Trunk: 2 -PortName Status Weight Ethernet0/0/3 Up 1 Ethernet0/0/4 Up 1從以上信息看出Eth-Trunk 1中包含2個成員接口Eth0/0/3和Eth0/0/4。成員接口的狀態都為Up。五、配置文件Switch的配置文件# sysname Switch# interface Eth-Trunk1 port link-type trunk port trunk allow-pass vlan 1