海洋石油鉆井英語(分類整理-非常好)

1、A Handbook of English for Offshore Oil Drilling 海洋石油鉆井常用英語手冊Drilling 鉆井 Carry out drilling operation in accordance with the drilling program. 按鉆井程序進行鉆井作業. Prepared bell nipple. 準備”喇叭口”短節. Make up 2 joints of drill pipe. 接兩根鉆桿. Break out this connection. 卸開該接頭. Run hole opener to sea bed. 下擴眼器到海底 Mix

2、 gel fluid for drilling conductor hole. 為鉆導管井眼配制高粘度泥漿. Make up bottom hole assembly. 組合下部鉆具 Check and reset crown-saver on every tour. 每個班都要檢查并重新調整天車防碰裝置. Number stands on trip out and trip in. 起下鉆時給立柱編號. Pick up BHA and run to seafloor. 將下部鉆具下到海底. Pick up stands. 接立柱 Dont drill faster than 15 minut

3、es for 1 stand. 鉆進速度別超過15分鐘1根立柱 Drop TOTCO. 投(陶特)測斜儀 Fish TOTCO with overshot. 用打撈筒撈起測斜儀 Resume drilling to T.D. 繼續鉆進到總深 Circulate 15 minutes.循環15分鐘 Run in hole. 下鉆 Put out of hole. 起鉆 Make an inventory of all ring gaskets. 開一個所有墊圈的清單 Use spinning tong. 使用氣動扳手 Operate the air winch. 操作氣動絞車 Lay down

4、57 joints of 5” drill pipe. 甩57根鉆桿 Pick up drill stem test tool. 提起鉆桿測試工具 Circulate mud for 2 hours. 循環泥漿2小時 Move string during circulation. 在循環時注意活動鉆具 Circulate hole clean. 循環清洗井眼 Circulate bottoms up. 循環泥漿幾周 Fill up every 5 stands. 每5柱灌泥漿一次 Check mud weight every 15 minutes. 每15分鐘檢查泥漿比重 Reverse ou

5、t excess cement. 反循環替出多余的泥漿 Change/replace old mud by new mud. 用新的泥漿替換出舊的泥漿 Stop drilling. 停止鉆進 Drilling ahead. 鉆進 Pull out of hole bit. 起出鉆頭 Change bit. 換鉆頭 Run the wear bushing. 下抗磨補心 The bit thread type is regular pin. 鉆頭絲扣是正規公扣 Whats the make-up torque? 上扣扭矩要多大? Run in 9” collars. 下9”鉆鋌 The cath

6、ead cant give enough torque. 貓頭力量不夠 Connect crossover sub. 接上配合接頭 The tong angle is too small. 大鉗的角度太小了 Stop circulating. 停止循環泥漿 Break out the stand. 卸立柱 Set the single into the mousehole. 把這個單根放進鼠洞 Can we break out the pipe with rotary table? 可用轉盤卸扣嗎? No! Break it out with tong. 不行! 要用大鉗卸扣 Spin it

7、out with the air spanner. 用氣動扳手卸扣 Put the pipe wiper on the string. 裝上鉆桿刮泥器 Dont set this stand back. 這根鉆桿不要放在鉆桿盒上 Make up the lift sub. 接好提升短節 Secure the safety clamp. 上緊安全卡瓦 The bit is nearing the shoe. 鉆頭快到套管鞋了 Slow down the running speed. 放慢下放速度 This is the undergauged interval. 這是縮徑井段 This is t

8、he drilling program. 這是鉆井設計書 How much weight on bit is required? 要加多少鉆壓? Keep the rotary speed at 120-140 RPM. 轉速保持120-140轉/分 Keep the flow rate at 3000 LPM. 保持排量3000升/分 The pump pressure is too high. 泵壓太高了 Dont ream the hole too fast. 劃眼不要太快 Notice the rotary torque. 注意轉盤扭矩的變化 The penetration rate

9、is getting slower. 鉆速變慢了 The bit is nearly worn out. 鉆頭快磨光了 Stop drilling at 2000 meters. 鉆至2000米停鉆 Circulate for one hour. 循環一個小時 The pump pressure has increased. 泵壓升高了 One nozzle may be plugged. 可能有一個水眼(或: 噴嘴)堵了 What is the hook load? 懸重多少? Whats the pick-up weight? 上提重量是多少? Whats the lowering wei

10、ght? 下放重量是多少? Run in HWDP. 下加重鉆桿 A stabilizer is needed here. 這里需要一個扶正器 This is a flexible sub. 這是撓性接頭 This is the BHA log. 這是下部鉆具組合記錄 Record all outside and inside diameters. 記錄好所有(入井工具的)內外徑 We need a short drill collar. 需要一根短鉆鋌 Pull the cat line. 拉貓頭 Operate the break lever. 操作(或:扶)剎把 Stop the pum

11、ps. 停泵 Make a wiper trip. 通井 Retrieve wear bushing. 取出抗磨補心 Bleed off pressure. (釋)放壓(力) Keep 5 wraps on the drum. 滾筒上留5圈 Set slips. 座上卡瓦 If tight hole, repeat wiper trip. 如果井眼緊, 重復劃眼 Setback bottom hole assembly. 將下部鉆具立于鉆桿盒內 Make sure all alarms are on. 確保所有的警報信號都開著 Lay down TDS spinner. 拆下頂部驅動的旋扣器

12、Run in hole bit #15 to bottom. 用15號鉆頭下鉆到井底 Run in hole to casing shoe. 下鉆至套管鞋 Pick up same bit and BHA. 裝上同樣的鉆頭和鉆具組合 Lay down 5” HW drill pipe. 甩5”加重鉆桿 Move string every 2 hours. 每2小時活動鉆具一次 Keep area around shaker clean. 保持振動篩區域干凈 Control trip gas. 控制起下鉆氣 Ream if needed. 如必要時進行劃眼 Select the best pen

13、etration rate. 選擇最佳鉆進速度 Fix the traveling assembly. 固定游動系統100. Check power tongs and spinning rope are on drill floor. 檢查動力鉗和尾繩是否在鉆臺Whats the weight on bit? 鉆壓是多少? What is the BHA of this well? 這口井的下部鉆具如何組合? Drill out cement. 鉆穿水泥 Drill out 20” casing shoe. 鉆穿20”套管鞋 Latch the elevator. 扣吊卡 Unlatch t

14、he elevator. 開吊卡 Set the slips. 放卡瓦 Adjust the crown-o-matic (crown saver). 調整防碰天車 Lock the hook pin. 鎖緊大鉤銷子 Check OD of stabilizer. 檢查扶正器的外徑 Perform leak off test. 進行地層破裂(或:滲漏)測試 Connect kill and choke line. 接上壓井和放噴管線 Reverse out the drill pipe. 反循環清洗鉆桿 Make a short trip. 進行短途起下鉆 Change the cutters

15、. 換割刀 Slug the pipe. 灌重泥漿 Drill the stand down. 鉆完立柱 Start/run the shale shaker. 開振動篩 Start the desanders. 開除砂器 Start the desilters. 開除泥器 Change it with a 40 mesh screen. 換成40目篩布 Shut it off. 關掉 Pull it to the cat ramp. 把它拉到坡道上去 Make a fast connection. 接單根要快 Dont dump the mud into the sea. 不要把泥漿排放到海

16、里 Disconnect it with a chain tong. 用鏈鉗卸開 Put a thread protector. 加一個(絲扣)護箍 Can we use the power slips? 可以使用動力卡瓦嗎?Casing and Cementing 下套管與固井 Run in hole to bottom for wiper trip. 下鉆通井 This is the casing program. 這是套管程序 Prepare for running casing. 準備下套管 Make everything ready for running 7”casing. 做好下

17、7”套管的準備 Make cementing job. 固井 Displace cementing with mud pump. 用泥漿泵替泥漿 Set cement plug from 2940 to 2790m. 在2940到2790米井段打水泥塞 Pick up cementing head. 接水泥頭 Cement samples are hard. 水泥樣已凝固 Pump in 3 cubic meters of spacer. 注3方隔離液 Pump down the plug. 泵壓(膠)塞 Wait on cement. 候凝 The guide shoe will be co

18、nnected. 接引鞋 Connect the floor collar. 接浮箍 Connect the air line to the casing stabbing board. 接好套管 扶正臺的氣管線 Run casing with the 350T slip elevator. 用350噸卡瓦式吊卡下套管 Clean and dry 20” casing threads with rags. 清潔并擦干20”套管絲扣 Where is the rabbit for drifting the casing? 套管通徑規在哪里?Rig Move, Anchoring and Posi

19、tioning 拖航, 拋錨, 定位What is our position now? 我們現在船位在哪里? Whats the moving speed now? (Whats the towering speed?) 拖航速度是多少? The speed is about 4 knots. 船速是4節左右 Which one is the main tug? 主拖是哪條船? The main tug is Nanhai 205. 主拖是南海205 Which one is the chase boat? 護航船是哪一條? How much is the horse power? 有多大馬力

20、? She has 6000 HP. 有6000馬力 Move the rig off location 50 feet. 將平臺移開50英尺 We are ready to drop the anchor. 我們已經做好拋錨的準備了 Secure all the movable equipment. 固定好各種活動的設備 Preload. (自升式)壓載 Ballast. (半潛式)壓載 Put the preload water into the tank. 向壓載艙灌壓壓載水 We need 5500 tons of preload water. 需要5500噸壓載水 Shall we

21、preload right now? 馬上開始?jí)狠d嗎? Drain the water off. 放水 The rig is overloaded. 平臺已超載 Jack up (jack down) the rig. 升(降)船 The draft is 3.5 meters. 船體吃水3.5米 The jetting pressure is 100psi. 沖樁壓力是100psi Penetrate the legs. 插樁 How much penetration do we have? 入泥多深了? No.1 and No.2 legs indicate 10 meters. 1,2號

22、樁腿插入10米 Fix the upper and lower wedges. 固定上下楔塊 Pay out the anchor line. 放出錨纜繩 Skid the derrick. 移開井架 The rig is short of potable water now. 平臺缺乏飲用水 Drop No.2 and No.3 anchors. 拋2號和3號錨 Why has the main engine stopped? 主機為什么停? Unleash the drilling tools. 卸開鉆具 Tighten up. 繃緊(或:上緊)一點 Turn on the cooling

23、 water for the windlasses. 開錨機剎車?yán)鋮s水 Retrieve the No.1 to No.8 anchors. 起1到8號錨 Check the paint marks at the anchor winches. 檢查錨機上的油漆記號 Prepare for a location move. 準備好移井位 Commence anchor handling. 開始起錨(或拋錨) Secure all equipment stored on deck. 固定好所有存放在甲板上的設備 Carry out stability and load calculations.

24、 做穩性和載荷計算 Pass pendant line, shackle and buoy to anchor handling vessel. 將起拋錨短索, 卸扣和浮標吊起給起錨船 Lower the windward anchor to seafloor. 拋上風錨到海底 Pick up the leeward anchor first. 先起下風錨 Take anchor chaser (or chaser) back to rig. 將撈/拋錨環送回平臺 Hook up towing lines to tug boat. 將拖纜連接到拖輪 Sound fog signal for t

25、wo seconds every twenty seconds. 發大霧信號, 每20秒鐘響兩秒Fishing 打撈 The bit cutters have been lost in the hole. 牙輪落井 Run in the reverse-circulation basket. 下反循環打撈籃 There is a lot of junk in the hole. 井下有很多落物 The fish is 235.46 meters long. 落魚長度235.46米 The fish top is at 2478.34 meters. 魚頂位置2478.34米Coring 取芯

26、Stop drilling for coring. 停鉆準備取芯 Make up core bit. 接取芯鉆頭 What type of core bit is it? 這是什么 型號的取芯鉆頭? Run in a diamond core bit. 下金剛石取芯鉆頭 Lets drop the ball for coring. 可以投球取芯 The core has been broken off. 巖芯斷了 Put the core in the boxes. 把巖芯裝在巖芯盒里 Dont brake suddenly. 不要猛剎車 Take out the core. 巖芯出筒 How

27、 long is the core? 巖芯多長 The core recovery is 98%. 巖芯收獲率是98% Run in the core barrel again. 繼續下巖芯筒(或: 取芯筒) Run in hole core barrel. 下取芯筒 Drop ball. 投鋼球 Recover core. 取出巖芯 Use same parameters as for core #1. 使用與1#取芯同樣的參數Freeing Stuck Pipe 卡鉆與解卡 The down-hole problems are very complicated. 井下情況很復雜 The h

28、ole is tight. 遇阻了 Overpull while tripping out. 起鉆遇卡(overpull: 超拉力) The formation is unstable. 地層不穩定 The wall caving is severe. 井壁垮塌嚴重 There are many return cuttings. 返出巖屑特別多 The mud returns have decreased. 返出泥漿減少 The hole is enlarged. 井眼擴大了 The pipes stuck. 卡鉆了 Pull up to 150 tons. 上提150噸 Slack off

29、to 50 tons. 下放至50噸 Ream down all the tight points. 在所有遇阻點進行劃眼 The rotary table cant rotate. 轉盤轉不動 Where is the sticking point? 卡點在哪里 Make a tensile test. 做拉伸試驗 Back it off above the free point. 在卡點以上倒扣 Where is the back-off position? 脫扣位置在哪 Plug the well for side tracking. 打水泥塞側鉆Abnormal Well Condit

30、ion and Well Control異常井況與壓井 The mud is gas out. 泥漿有氣侵 The pit has lowered quickly. 泥漿池液面下降很快 The hole lost returns. 井口不返泥漿 The returns are unstable. 返出泥漿量忽大忽小 Wheres the thief zone? 漏失層在哪里 Cut down the flow rate. 降低排量 Lower the mud density. 降低比重 Cut down the hydrostatic pressure. 減少靜壓 The gas smell

31、is strong. 天然氣味度很濃 Theres some trace of oil. 發現有油花 The pump pressure is fluctuating. 泵壓不穩 It is a zone of abnormal pressure. 這是異常壓力層 The hole (well) is kicking! 井涌啦! Shut in the BOP! 關閉防噴器 Sound the general alarm quickly! 快發出綜合警報 The stand pipe pressure is 10 kg/cm2. 立管壓力10公斤/厘米2 The casing pressure

32、 is 25 kg/cm2. 套壓2510公斤/厘米2 Fill out the kill sheet. 填寫壓井記錄表 Kill the well. 壓井 Theres a combination of lost returns and the kick. 又噴又漏, 情況復雜 Reverse the gas out of the hole. 反循環排氣 Whats the lag time? 遲到時間是多少 The well is now stable. 現在井眼已經穩定BOP and subsea Equipment 防噴器與水下設備 Cut off the 30” conductor.

33、 割掉30”隔水管 Weld on the 30” bottom flange. 焊接30”法蘭 Hoist and nipple up 30” diverter. 吊裝30”轉噴器 Change the 5” pipe rams to 3-1/2” rams. 把這個5”閘板換成3-1/2” Install blind ram. 安裝防噴器的盲板芯子 Check the seal ring of the conductor. 檢查隔水管密封圈 Cut off the lifting eye of the conductor. 切割隔水管耳環 Test BOP. 測試防噴器 Change an

34、nular BOP packing. 更換萬能防噴器芯子 Full pressure test the ram preventers. 對閘板防噴器進行全壓試壓 Test annular BOP at 2500psi. 萬能防噴器試壓至2500psi Check annular pressure. 檢查環形空間壓力 Confirm the angle of the guide base. 確定基板角度 The thread is covered with the quick-release protectors. 已戴好快卸護絲 Establish the guide lines. 裝導向繩

35、Connect the TGB running tool. 接臨時導向基板送入工具 Land the TGB to sea. 下臨時導向基板到海底 Retrieve the running tool. 退出送入工具 Run the BOP and risers. 下防噴器和隔水管 Pick up the marine riser. 吊出隔水管 Pick up the slip joint. 起伸縮節 Adjust the riser tensioners. 調整隔水管張力 Function test the diverter system. 對防噴器系統進行功能測試 Retrieve the

36、pin connector. 取出銷釘連接器 Move the BOP to the moonpool door. 將防噴器移到園井甲板的活動門上 Run the test plug. 下試壓塞 Close the upper pipe ram. 關上部鉆桿閘板防噴器 Open the kill line valve. 開壓井管線閥 The compensation capacity is 400000 pounds. 補償能力是400千磅 The locking load is 1000000 pounds. 鎖緊負荷1000千磅 Support the riser. 接隔水管支撐環 Rem

37、ove the hose bundles. 卸下垮接軟管 Assure the self-controlled rotation. 保證自控轉動 Set the LMRP on the test pump. 將下部防噴器插入總成座放到試壓樁上 Connect the flex joint to the riser. 連接隔水管與撓性接頭 Land the BOP onto the well head. 座防噴器到井口頭 Run the subsea TV for monitoring. 下水下電視觀察 Remove all the riser running tools. 取出所有的隔水管送入

38、工具 BOP carrier. 防噴器叉車 Lower the universal guide frame. 下放萬能導向架 Paint mark the top 6 meters of 30” conductor white. 在30”隔水管的頂部6米處用白漆涂上記號 Check adequate length for guidelines. 檢查導向繩的長度是否足夠 Move temporary guide base (TGB) into moonpool. 將臨時導向基板到園井甲板 Test pull to check connection. 試?yán)瓩z查連接 Grease TGB and

39、running tool as required. 按要求給導向基板及下入工具上黃油 Test fit TGB and running tool. 用下入工具試臨時導向基板連接 Check for junk inside shoe joint. 檢查浮鞋內有無落物 Pick up 30” conductor handling slings and shackles. 吊上下30”導管的索具和卸扣 Is slope indicator properly mounted? 水平儀是否裝好? Ensure subsea TV is in good condition. 確保水下電視處于良好的狀態 P

40、lace BOP stack on the test pump. 將防噴器組放在試壓樁上 Check condition of all 30” casing connectors. 檢查所有30”套管接頭的情況 Replace O-rings as required. 按需要, 更換O性密封圈 Attach slope indicator below camera position. 在攝像機下面裝上水平儀 Inspect and repair diverter. 檢查并修理轉噴器 Prepare spud plate and wireline to check water depth. 準備

41、測深板和鋼絲繩測量水深 Record all pressure tests on a chart recorder. 用試壓表記錄試壓記錄 Visually inspect all sealing element. 目視檢查所有密封件 Check and tighten all bolts. 檢查并上緊所有螺栓 Bleed off surface accumulators. 地面管線排空氣 Check for leaks. 檢查有無泄漏 Lift BOP stack and replace wellhead connector AX ring. 吊起防噴器組并更換連接器AX密封圈 Functi

42、on test wellhead. 對井口頭進行功能試驗 Fill kill and choke valves with seawater. 將壓井閥和阻流閥注滿海水 Pressure test to 500psi then bleed off test pressure. 試壓到500psi, 然后放掉壓力 Reduce hydraulic control manifold pressure to 5200 kpa. 將液壓控制管線壓力減少到5200千帕 Switch to alternate control pod. 把閘門開關倒到控制面板 Guidelines are slacked o

43、ff. 導向繩松了 Slack off drill pipe and release running tool. 放松鉆桿并卸開下入工具 Run subsea TV to observe bit entering the TGB. 下水電視觀察鉆頭是否進入臨時導向基板 Dont rotate until hole opener passes through the TGB. 在擴眼器通過臨時導向基板前不要旋轉 Position permanent guide base (PGB) below rotary table. 在轉盤下安放永久導向基板 Monitor riser level via

44、trip tank. 用計量罐來控制隔水管內的液面 Pressure test to 5000psi. 試壓5000psi Pick up test mandril and place in BOP. 吊起試壓防噴器芯子并裝入防噴器組 Safety and Firefighting 安全與消防 Get a Work Permit before you can start the hot work. 辦理作業許可證才能進行動火作業 Welding is not allowed. 不準動焊 Put on your (safety) helmet. 戴上安全帽 Its a high voltage

45、area. 這是高壓區 Thats against the rule. 這是違章作業 Dont walk under the crane load. 不要在吊物下走動 The repairing is under way. 正在檢修 Keep your hands clear! (Keep you hands off! Do not touch!) 不要亂動 Wear and secure your safety belt. 戴上并系好安全帶 Life jacket must be worn when working outboard or overhead. 舷外或高空作業要穿救生衣 Hav

46、e your breathing apparatus near you. 保持放毒面具在附近 Its a drill. 這是演習 It was a BOP drill. 這是防噴演習 Get in the lifeboat in order. 按順序進入救生艇 Put on life jacket! 穿好救生衣 Abandon the vessel! 棄船 Sound the abandonment alarm! 發出棄船警報 Go to the helideck! 去飛機坪集合 Aboard the lifeboat. 登上救生艇 Aboard the supply boat to shor

47、e! 乘拖船上岸 Check life saving apparatus periodically. 定期檢查救生設備 Its for fire fighting. 這是消防用的 Start the fire pump. 啟動消防泵 This rope is too small. 這根繩子太細了 It should be function tested. 需做功能測試 A warning notice should be set up. 要掛警告牌 Do you have an emergency program (contingency plan)? 你們有沒有應急計劃? It must b

48、e ready in an emergency condition. 必須始終保持良好的應急狀態 Will the typhoon hit our rig? 臺風要襲擊我們的平臺嗎? We will have to evacuate the rig. 我們要撤離平臺 Personnel on board (POB). 在船人員總數 Sound fire alarm. 發消防警報 This is a fire drill. 這是消防演習 conduct abandon ship drill. 舉行棄船演習 Release the boat hooks. 釋放救生艇吊鉤 Board the lif

49、e boat. 登救生艇 Remove the rust and paint with anti-corrosive primer. 除銹后上防銹底漆 Three rafts are located near life boat station port side. 在左舷救生艇站附近還存放有3個救生筏 Wear work vests when working below the cellar deck. 在圓井甲板面下面工作時須穿工作救生衣 The station bills need to be updated. 應急部署表須更新 Check the expiry date for all

50、 foam extinguisher. 檢查所有泡沫滅火器的過期時間 Close all the water-tight doors. 關閉所有水密門 Safety procedure shall be followed at all the times. 在任何時候都應遵守安全程序 Anchor wires should have a Spelter type socket at anchor side. 拋錨繩靠錨的一端應使用鋅壓頭 Colour code all the connection at the loading station. 在供給站管線接頭處用顏色表明各管線 Verify

51、 that a high level alarm is installed on the sludge tank. 確認污水艙安裝有高位警報 Dont switch on during drilling operation. 鉆井作業期間不能合閘 Provide two independent means to start the emergency generator engine. 應急發電機柴油機應有兩套獨立的起動方法 Have the boom pennant wires of port crane re-certified. 重新認證左舷吊車扒桿變幅繩 Clean the inter

52、nals of the emergency switchboard. 清潔應急配電盤內部Helicopter and Supply Vessel 直升機與供應船Load out Contractors riser at Zhanjiang anchorage. 在湛江錨地把承包商的隔水管裝上平臺 Offload casing. (從供應船上)卸套管 Load (offload or unload) the boat. 裝(卸)船 Get the food container loaded on the boat. 把食品集裝箱裝上船 The helicopter will land on ri

53、g soon. 直升機很快就要在平臺降落 Tell the base to get (or send) a chopper here. 通知基地派飛機來 Helicopters are not allowed to land here. 飛機不能降落 Report the weather condition to the pilot. 向飛行員報天氣 Inform the boat come to standby. 通知拖輪過來待命 Call the boat to come along port side. 通知拖輪過來靠左舷 We will take the personnel baske

54、t. 我們乘坐吊籃Repair and Maintenance 檢修Have an overall check. 進行全面檢查 MPI the brake linkage system. 對剎車連接系統進行磁粉探傷 Demonstrate that the make-up cathead can pull 7000 lbs. 證明上扣貓頭能拉到7000磅 Determine the origin of the air leak and rectify this. 找出漏氣的地方并處理 Adjust the brake band equalizer beam properly. 適當調整剎帶平衡

55、梁 Note that the 3000 hour inspection on TDS is due. 注意頂驅的3000小時保養時間已到 Check sheave rope pocket wear with a 1 3/8”+1 1/32 template. 用1 3/8”+1/32”量規檢查繩槽磨損的情況 Repair the handrails on the crown. 修理天車臺的欄桿 Function test the anti-freefall brake on monthly basis. 每月對天車防碰裝置進行功能試驗 Get me a spanner, please. 請遞

56、給我一把扳手 Renew brake rim because of excessive wear. 更換磨損嚴重的剎車鼓 Clearly mark safe working load (SWL) on the air winch below the rig floor. 表明鉆臺底下氣動絞車的安全工作負荷 Measure the master bushings for wear. 測量主補心磨損情況 Have BOP ram opened up for internal inspection. 打開防噴器閘板進行內部檢查 Install a ground cable on the triplex pump motor. 給三缸泵馬達安裝接地線 We need a 48” pipe wrench. 我們需要一把48”的管鉗 Strike it with a sledge hammer. 用大錘打 We want a triangle file. 需要一把三角銼刀 Tighten up the screw. 緊一下螺絲 Check it with a level. 用水平尺量一下 Put some en