發電機檢測中英文對照

1、發電機的檢測(中英文對照 )1. INSPECT GENERATOR BRUSH HOLDER ASSEMBLY檢查發電機碳刷裝置(a) Using vernier calipers,measure the exposed brush legth. 。用游標卡尺測出露在外面的碳刷的長度Standard exposed length:標準長度9.5 to 11.5 mm (0.374 to 0.453 in.)9.5 to 11.5 mm (0.374 to 0.453 in.)Minimum exposed length:最小長度1.5 mm ( 0.059 in.)1.5 mm ( 0.05

2、9 in.)If the exposed length is less than the minimum, neplace the generator brush holder assembly.如果碳刷長度小于最小值，替換發電機的碳刷裝置。2. INSPECT GENERATOR REGULATOR ASSEMBLY檢查發電機調節器裝配(a) Using an ohmmeter, check the continuity between terminals F an B（ a）使用歐姆表，檢查F 與 B 之間的是否連通。Standard:標準 .When the positive and n

3、egative poles between terminals F and B are exchanged, there is continuity in one direction but no continuity in the other direction.當 F 和 B 之間的正極和負極被交換時，有在一個方向是連通的，但是在另一個方向的沒有連通的。If the continuity is not as specified, replace the generator regulator assembly.如果不是規定的連通值，替換發電器調節器裝配(b) Using an ohmmet

4、er, check the continuity between terminals F and E.（ b）使用歐姆表，檢查F 與 E 之間是否連通。Standard:標準：When the positive and negative poles between terminals F and E are exchanged, there is continuity in one direction but no continuity in the other direction.當 F 和 B 之間的正極和負極被交換時，有在一個方向是連通的，但是在另一個方向的沒有連通的。If the co

5、ntinuity is not as specified, replace the generator regulator assembly.如果不是規定的連通值，替換發電器調節器裝配3. INSPECT GENERATOR DRIVE END FRAME檢查發動機定子線圈(a) Check the stator coil for open circuits.檢查定子線圈的開路。(1)Using an ohmmeter, check the resistance between the coil leads.（ 1）用歐姆表，檢查電阻線圈之間的電阻。Standard resistance:標準

6、電阻：Below 1 低于 1If the result is not as specified, replace the generator assembly.如果不是規定電阻值，替換發電器定子線圈 裝配(b)Inspect the stator for ground.檢查定子線圈是否接地。(1) Using an ohmmeter, check the resistance between the coil lead and drive end frame.使用歐姆計，檢查定子線圈與發動機殼體的電阻、Standard resistance:標準電阻：10 K or higher10K 或更

7、高If the result is not as specified, replace the generator assembly.如果不是規定電阻值，替換發電器定子線圈 裝配(c) Inspect the bearing.（ c）檢查軸承。(1) Make sure that the bearing is not rough or worn.軸承是否粗糙或磨損過度。If necessary, replace the generator assembly.如果有必要， 替換發電器裝配。4 INSPECT GENERATOR HOLDER WITH RECTIFIER 4 檢查發電機整流器(a

8、) Using an ohmmeter, check the continuity among terminals P1, P2, P3 and B, andamong P1, P2, P3 and E.使用歐姆計，檢查P1、 P2、 P3 和 B 之中和在P1、P2、 P3 和 E 之中是否連通Standard:標準When the positive and negative poles among terminals P1, P2, P3 and B are exchanged, there is continuity in one direction but no continuity

9、in the other direction.當 P1、P2、P3 和 B 之中的正極和負極交換時，有在一個方向是連通的，但是在另一個方向沒有連通。When the positive and negative poles among terminals P1, P2, P3 and E are exchanged, there is continuity in one direction but no continuity in the other direction.當 P1、P2、P3 和 E 之中的正極和負極被交換時，有在一個方向的連通的，但是在另一個方向沒有連通。If the cont

10、inuity is not as specified, replace the generator holder with rectifier.如果不是規定的連通值，將替換發電機整流器。5. INSPECT GENERATOR ROTOR ASSEMBLY5 。檢查發電機轉子裝配(a) Check the generator rotor for open circuits.一）檢查發電機轉子開路。(1) Using an ohmmeter, measure the resistance between the slip rings.（ 1 ）用歐姆表，測量的滑環之間的電阻。Standard r

11、esistance: 1.7 to 2.1 at 20oC(68oF)標準電阻：在 20oC (68oF)的情況下1.7 到 2.1If the resistance is not as specified, replace the generator rotor assembly.如果不是規定電阻值，替換發電器轉子 裝配(b)Check the generator rotor for short circuits.（二）檢查發電機轉子的短路。(1) Using an ohmmeter, check the resistance between the slip ring and genera

12、tor rotor assembly.（ 1）用歐姆表，檢查滑環和發電機轉子之間的電阻。Standard resistance:標準電阻：10K or higher10K 或更高If the result is not as specified, replace the generator rotor assembly.如果不是規定電阻值，替換發電器轉子 裝配(c)Inspect the slip rings.（ c ）檢查的滑環。(1) Make sure that the slip rings are not rough or scored.（ 1 ）滑環不否粗糙或磨損過度。If rough or scored, replace the generator rotor assembly.如果 粗糙或磨損過度，替換發電器電動機滑環 裝配(2) Using vernier calipers ,measure the slip ring diameter.（ 2 ）用卡尺，測量滑環的直徑。Standard diameter:標準直徑：14.2 to 14.4 mm (0.559 to 0