注塑常用術語英文表達

1、1.霧氣 Moisture Streaks2.玻纖安排不均 Glass Fiber Streaks3.困氣 Gas Trap Effect4.銀絲紋 Sliver Marks5.結合線 Weld Line6.水波痕 Water Wave Effect7.黑點 Dark Sport8.頂出印 Visible Ejector Marks9.變形 Deformation During Demolding10.填充不足 Short Filling11.冷料流痕 Cold Slug12.進膠口點不良 Dull Spots Near The Sprue13.噴射痕 Jetting14.表面起層 Flaki

2、ng Of The Surface Layer15.浮泡 Entrapped Air16.過熱變色 Burnt Streaks17.龜裂 Stress Crack18.縮水痕 Sink Marks19.真空氣泡 Density Bubble20.披鋒 Flash21.擦傷印 Scratch MarksGlass fiber rich surface/glass emergence on the surface22 尺寸過大 Over dimension23尺寸過小 Under dimension 24 翹曲 Warpage/warped 25 收縮 Shrinkage/shrink 26 縮影

3、 Sink marks 27 打不滿 Short shot/short molding 塑料模具mould of plastics 注塑模具injection mould 沖壓模具die 模架mould base 定模座板Top clamping plate Top plate Fixed clamp plate 水口推板stripper plate A板A plate B板B plate 支承板 support plate 方鐵 spacer plate 底針板 ejector plate 面針板 ejector retainer plate 回針 Return pin 導柱 Guide p

4、in 有托導套 Shoulder Guide bush 直導套 Straight Guide bush 動模座板Bottom clamp plate Moving clamp plate 基準線datum line 基準面datum plan 型芯固定板core-retainer plate 凸模固定板punch-retainer plate 頂針ejector pin 單腔模具single cavity mould 多腔模具multi-cavity mould 多澆口multi-gating 澆口gate 缺料starving 排氣breathing 光澤gloss 合模力mould cla

5、mping force 鎖模力mould locking force 擠出extrusion 開裂crack 循環時間cycle time 老化aging 螺桿screw 麻點pit 嵌件insert 活動鑲件movable insert 起堊chalking 澆注系統feed system 主流道 sprue 分流道runner 澆口gate 直澆口direct gate , sprue gate 輪輻澆口spoke gate , spider gate 點澆口pin-point gate 測澆口edge gate 潛伏澆口submarine gate , tunnel gate 料穴col

6、d-slug well 澆口套sprue bush 流道板runner plate 排飛槽vent 分型線（面）parting line 定模stationary mould，F(xiàn)ixed mould 動模movable mould, movable half 上模upper mould， upper half 下模lower mould， lower half 型腔cavity 凹模cavity plate，cavity block 拼塊split 定位銷dowel 定位銷孔dowel hole 型芯core 斜銷angle pin, finger cam 滑塊slide 滑塊導板slide

7、guide strip 楔緊塊heel block, wedge lock 拉料桿sprue puller 定位環locating ring 冷卻通cooling channel 脫模斜度draft 滑動型芯slide core 螺紋型芯threaded core 熱流道模具h(yuǎn)ot-runner mould 絕熱流道模insulated runner mould 熔合紋weld line （flow line） 三板式模具three plate mould 脫模ejection 換模腔模具 interchangeable cavity mould 脫模劑release agent 注射力量sh

8、ot capacity 注射速率injection rate 注射壓力injection pressure 差色劑colorant 保壓時間holdup time 閉模時間closing time 定型裝置sizing system 陰模female mould，cavity block 陽模male mould 電加工設備Electron Discharge Machining 數控加工中心CNC machine center 萬能鐵床Universal milling machine 臥式刨床Horizontal planer 車床Engine lathe 平面磨床Surface grinding machine