發電機安全培訓

1、Confidential2013-09-181迅迅得機械（珠海保稅區）有限公司得機械（珠海保稅區）有限公司為了您的安全Confidential2013-09-182 警警告標志和標牌告標志和標牌 1.在我們所有的發動機上有一些關于安全的標志。請你們花一些時間親自去熟悉這些安全標準的位置和內容。2.在安裝現場所有的安全標準都應清晰可見，如果看不清文字和圖樣，就應擦洗和更換。擦洗標牌時要用抹布，水和肥皂。不要用溶劑或汽油等，這些溶劑和汽油會松懈標志的粘著物質，使標準掉下來。3.如果標牌已損壞，丟失和看不清，你就應該必須另換一個。4.在你閱讀并理解操作和保養手冊中的說明和警告之前，不允許操作發動機和

2、在發動機上工作。不按照說明去做或忽視警告都會造成發電機組的損壞或人身傷亡事故。Confidential2013-09-183 危危險事項險事項1. 在保養或進行發電機組維修之前，應在啟動開關或操作桿上懸掛“不準操作”或類似的警告標牌。2. 對發電機組正在進行保養或維修時不允許未經許可的人員靠近發動機。并將發電機組控制屏的緊急停機按鈕按下，發電機輸出開關應在OFF（關斷）位置。3. 根據工作條件的需要，進入發電機組安裝現場應戴上安全帽，穿戴好防護服需要時應佩戴防護眼睛和其它保護用品。4. 如果時在一個密封的地方運轉發動機時應佩戴防護耳朵的裝置，以防損壞聽力。5. 工作現場不要穿著過于肥大的防護服

3、和佩戴首飾，這些都有可能掛在操縱桿或發動機的其它零部件上。6. 確認所有的防護或蓋罩在發動機上固定就位。7. 使用所有清洗劑時要小心。不要將保養溶液放在玻璃容器內，因?yàn)椴Ａ萜饕讚p壞。8. 千萬不要試圖修理自己不懂的東西，不要用你不知道那如何使用的工具或設備。Confidential2013-09-184除非另有規定，在進行所有的維修保養項目時應進行以下操作除非另有規定，在進行所有的維修保養項目時應進行以下操作1.停止發動機的運轉，當發動機在運行時不要對發動機本體進行修理或調整發動機的被驅動設備。2.進在發電機組上懸掛警告標志，將發電機組的緊急開關壓下。3.行維修保養電氣系統之前斷開啟動蓄電池

4、。4.不要修理自己不懂的東西。5.采用適當?shù)墓ぞ吒鼡Q或修理損壞的設備。6.只允許在發電機組的控制面板上對發動機進行啟動或停機。決不能短接啟動馬達接線柱或蓄電池，因?yàn)殡娏髂芘酝òl(fā)動機空擋啟動系統，損壞電氣系統。7.在修理燃油系統后啟動發動機時，一旦發動機發生超速，馬上關閉發動機的燃油供給切斷發動機的進氣，使發動機停車。Confidential2013-09-185壓縮空氣和水壓縮空氣和水1.壓縮空氣可以造成人身傷害。當用壓縮空氣進行清洗時請務必戴上防護面罩，穿好防護服及防護鞋。2.清洗設備時的空氣壓力必須低于205千帕（30磅/平方英寸）。3.當清洗冷卻系統時，任何時候都要戴上防護眼鏡。帶有壓力

5、的水流能導致碎屑噴出來，造成人身傷害。Confidential2013-09-186液體的穿透力液體的穿透力 當檢查泄漏，必須用一塊薄板或紙板壓力下泄漏的液體，即使從針孔中泄漏也能穿透人體器官，造成嚴重傷害或死亡。Confidential2013-09-187石棉材料石棉材料1.當處理含有石棉纖維的零部件時要特別小心，避免吸入可能產生的粉塵。如果吸入這些粉塵將會危害健康。如果沒有辦法避免石棉粉塵時應戴好防塵口罩。Confidential2013-09-188對于管子、管路或軟管有下列情形時都要引起安全的注意：對于管子、管路或軟管有下列情形時都要引起安全的注意：1.末端接頭移位、損壞或泄漏2.軟

6、管外皮擦破或割開，加強鋼絲外露。3.軟管外層鼓抱。4.軟管彎曲部分扭曲或壓扁。5.金屬夾子嵌入軟管皮外。Confidential2013-09-189管路、管子和軟管管路、管子和軟管 1.保養維修時應仔細檢查所有管子、管路或軟管。不要彎折或敲擊高壓油管。決不允許使用彎折或損壞的管子、管路或軟管。修復松動或損壞的燃油管、機油管或軟管，泄漏將會引發火災。Confidential2013-09-1810防止?fàn)C傷防止?fàn)C傷1.不要接觸運轉中的發動機任何部位。在發動機進行維修保養之前應先讓發動機冷卻下來。2.在斷開或卸下任何管子、接頭或相關零部件之前，應釋放存在于氣體、機油、燃油或冷卻系統中的全部壓力。C

7、onfidential2013-09-18111. 打開散熱器的端蓋時注意!2.運轉中和運轉后，不要立即打開散熱器的端蓋。運轉中和運轉后冷卻水處于高溫狀態，打開端蓋時蒸汽和熱水的噴出會造成人員的燙傷事故。要等發動機冷卻至常溫后及壓力釋放后用布包裹住散熱器端蓋緩慢擰松。另外使用后要確認檢查散熱器的端蓋是否確實擰緊。Confidential2013-09-1812冷卻液冷卻液 1.為了防止?fàn)C傷不要爬上在運轉或未冷卻下來的發動機去拆卸加注冷卻水的加注蓋子。在工作溫度下發動機的冷卻水是熱的并有壓力。散熱器和所有通向加熱器或發動機的管路內，都有熱水。當壓力釋放很快時，熱水將會變?yōu)檎羝?.接觸熱水或蒸汽

8、能造成嚴重的燙傷。在排放前，應使冷卻系統部件冷下來。只能在發動機熄火后加注口蓋冷卻到可以用手?jǐn)Q開時，方可檢查冷卻水液面。3.冷卻水中可能會含有防銹劑或防凍液。為了防止人身的傷害避免于皮膚和眼睛接觸，更不能飲用。Confidentialwww.schmid-THANK YOU FOR YOUR ATTENTION!2013-09-1813Please feel free to contact us if you have any questions:Forename Surname | Job Title | Organizational UnitPhone +49 7441 538-123 |

9、 Mobile +49 172 7091-123surname.foschmid-ConfidentialThe information contained in this presentation is for background purposes only and is subject to amendment, revision and updating. This presentation may imply forward-looking statements that are based on managements current views and involve risks

10、, assumptions and uncertainties which could cause actual results, performances or events or other circumstances to differ materially from those expressed or implied by the forward-looking statements. Forward-looking statements can be identified by reason of context, including without limitation, sta

11、tements referring to risk limitations, operational profitability, financial strength, performance targets, profitable growth opportunities and risk adequate pricing, as well as the words may, will, should, expects, plans, intends, anticipates, believes, estimates, predicts, or continue, potential, f

12、uture, or further, and similar expressions. Statements contained in this presentation regarding past trends or activities or other circumstances should not be taken as a representation that such trends or activities or other circumstances will continue in the future. SCHMID is not obligated to updat

13、e or revise any statements contained in this presentation. In particular, you should not place undue reliance on forward-looking statements, which speak only as of the date of this presentation.This information is being provided to you without any warranty or guarantee, express or implied, statutory

14、 or otherwise. Furthermore, SCHMID and/or any of its respective affiliated companies, officers, employees, advisors or agents shall not be liable or responsible in any other way or form for this presentation and its contents. By use and your acceptance of this information, you hereby agree to this disclaimer.Nothing in this presentation is intended to create or amend any legally binding relationship between SCHMID and the recipient hereof. Any legally binding relationship or any amendment of a legally binding relationship between SCHMID and the recipient hereof in connectio