維修手冊(cè)ad2816af-1610

1、SETUP INSTRUCTIONSAF-1610Automatic Document FeederNOTES Before setting up, be sure to unplug the power cord of the machine. Keep all packing materials out of the reach of children.Printed in ChinaAF-1610 Unpacking1. Check that the following items are available.1. Automatic Document Feeder12. Setup I

2、nstructions1 Installation of the Automatic Document Feeder1382U019AA1. Remove the Original Cover.* Only the specific areas, for which the copier is equipped with the Original Cover as stan- dard. 8 122. Position the Automatic Document Feeder.2. Remove the Protective Tape.1382U018AC4980U021AA1382U020

3、AA1382U030AA1382U021AA1382U023AA* To remove the Automatic Document Feeder, insert a tool into the round hole shown below and unhook the locking tab.3. Connect the hookup cable connectors of the Automatic Document Feeder.1382U022AA4. Tighten the fixing screw finger-tight. Height Adjustment1382U024AA1

4、. Check the clearance between the document scanning glass surface and the protrusion on the Duplexing Document Feeder side.* Raise and lower the Automatic Document Feeder and make the above check while the Scanner stays lit as a predrive sequence.OK5. Connect the power cord to a power outlet.6. Pres

5、s the main power switch on the I (ON) position. * If there is a clearance, adjust the height by following the procedure given below.NG 4980U016AB1382U025AC1382U026AA2. Turn the adjusting screws at the hinges of the Automatic Document Feeder so that the protrusion contacts the document scanning glass

6、.* Turning direction of the screwTurn the screw clockwise to raise the Auto- matic Document Feeder.Turn the screw counterclockwise to lower the Automatic Document Feeder. Producing a Test Pattern 4506U008AA1382U013CA1. Call the Service mode to the Display.* For the procedure to call the Service mode

7、 to the Display, see the Service Manual.2. Press the key four to show the FUNCTION mode.1382U011CA4506U022AA6. Press the Yes key. (Tray 1)* To select Tray 2, press the key. (Only when the PF-125 is mounted)1382U009CA4506U022AA3. Press the Yes key.1382U010CA1382U013CA4. Press the key.1382U008CA1382U0

8、01CB1382U008CA4506U022AA7. Press theorkey to select Pattern 1.8. Press the Yes key.1382U012CA4506U022AA5. Press the Yes key.1382U014CA1832U015CBtest pattern 4647D019AA9. Press the Start key.* The copier will automatically produce a test pattern. (Use the test pattern as the test chart.)10. Press the

9、 Panel Reset key to show the initial screen. Checking and Adjusting Skew Feed1. Draw a short line at each of positions (A) andAB(B) on the test pattern, each being 100 mmAdjustments If dimension (a) is longer than dimension (b),100mm100mm1382U031ABaway from the centerline.ab4647D019AAloosen the shou

10、lder screw shown in the illus- tration using a coin and slide the Automatic Document Feeder to the front.ba1382U027AA4647D019AA2. Load the test pattern in the Automatic Document Feeder and make one 1-sided copy five consecutive times.NOTELoad the test pattern lengthwise.3. Check to see if the dimens

11、ions (a) and (b) meet the following equation.Requirement: a b = 1.0 mm* If the requirement is not met, adjust the tilt.1382U028ABab4647D019AA If dimension (a) is shorter than dimension (b), loosen the shoulder screw shown in the illus- tration using a coin and slide the Automatic Document Feeder to

12、the rear.1382U029AA4. After the adjustment has been properly made, tighten the shoulder screw that has been loosened. Checking and Adjusting the FD Zoom Ratio1. Load the test pattern in the Automatic Document Feeder and make a full-size copy.NOTELoad the test pattern lengthwise.1382U027AA4688U208AA4

13、506U022AA5. Press the Yes key once to show the PRN MAIN REGIST screen.C4647D019AA2. Measure dimension C on the sample copy.* If dimension (C) is longer or shorter than that on the test pattern, perform the following pro- cedures to make an adjustment.1382U005CB1382U013CA6. Press the key six times. 3

14、. Call the Service mode to the Display.7. Press the Yes key.4506U008AA* For the procedure to call the Service mode to the Display, see the Service Manual.1382U004CA4506U022AA4506U008AA1382U013CA4. Press the key once to show the Adjust mode. 4688U211AA4506U022AA8. Press the Yes key.4688U212AA9. Using

15、 the or key, change the setting value. If the measurement of dimension C is greater than the specifications, decrease the setting value. If the measurement of dimension C isshorter than the specifications, increase the setting value.(Refer to the following table for the setting val- ues.) CD Registr

16、ation Adjustment1382U027AA1. Load the test pattern in the Automatic Document Feeder and make a full-size copy.NOTELoad the test pattern lengthwise.2. Fold the copy in half, correctly aligning both edges as shown.Setting ValueDetailSetting ValueDetail9598.0%101100.4%9698.4%102100.8%9798.8%103101.2%98

17、99.2%104101.6%9999.6%105102.0%100100.0%* Default setting value: 100 (100%)10. After the setting value has been entered, press the Yes key.1382U002AAcreaseD (center line)3. Check the crease and D (center line) on the copy. 4506U022AA1382U006CB1832U015CB11. Load the test pattern in position and press

18、the Start key.12. Check the copy.4647D026AAEF1382U017AA4. If the positions deviate, change the setting value by following the steps of 5 and onward to make the appropriate adjustment.4506U008AA5. Call the Service mode to the Display.* For the procedure to call the Service mode to the Display, see th

19、e Service Manual.1382U003CA4506U022AA9. Press the Yes key.4506U008AA1382U013CA6. Press the key once to show the Adjust mode.4688U211AA4506U022AA10. Press the Yes key.7. Press the Yes key once to show the PRINT MAIN REGIST screen.11. Using the or key, change the setting value. If D on the copy deviat

20、es on the E side, increase the setting value. If D on the copy deviates on the F side, decrease the setting value.(Refer to the table of next page for the setting4688U208AA4506U022AA4688U214AA1382U013CAvalues.)8. Press the key seven times.1382U005CB1382U013CAGSetting ValueDetailSetting ValueDetail90

21、-10 (-5.0 mm)101+1 (+0.5 mm)91-9 (-4.5 mm)102+2 (+1.0 mm)92-8 (-4.0 mm)103+3 (+1.5 mm)93-7 (-3.5 mm)104+4 (+2.0 mm)94-6 (-3.0 mm)105+5 (+2.5 mm)95-5 (-2.5 mm)106+6 (+3.0 mm)96-4 (-2.0 mm)107+7 (+3.5 mm)97-3 (-1.5 mm)108+8 (+4.0 mm)98-2 (-1.0 mm)109+9 (+4.5 mm)99-1 (-0.5 mm)110+10 (+5.0 mm)1000 FD Re

22、gistration Adjustment1. Check to make sure that dimension G falls within the range specified below.* Default setting value: 100 (100%)4647D026AA Requirement: G 20 3.0 mm* If dimension G falls outside the specified range, adjust as necessary.2. Call the Service mode to the Display.* For the procedure

23、 to call the Service mode to the Display, see the Service Manual. 12. After the setting value has been entered,press the Yes key.4506U008AA4506U022AA3. Press the key once to show the Adjust mode.1382U006CB4688U211AA1832U015CB13. Load the test pattern in position and press the Start key.14. Check the copy.4506U008AA1382U013CA4688U208AA4506U022AA4. Press the Yes key once to show the PRINT MAIN REGIST screen.AF-1610 9 1382U005CB1382U013CA4506U022AA1382U007CA4506U022AA5. Press the key eight times.6. Press the Yes key.Setting ValueDetailSetting ValueDetail90-10 (