外文翻譯--機器人化多功能護理床研究與探討

Robotic nanomanipulation multi-function nursing bed research and discussion Translators XXX Abstract: the humanized design is an important concept of modern design, it emphasizes ergonomics design products, ecology, from the Angle of aesthetics, which reflects the perfect technological people-oriented thoughts. The nursing bed was based on the idea of design, it can not only realize carried back, lift the thigh, curved crus and adjust sitting position, and the function of Pro/E design through 3d entity modeling software is simulated and simulation analysis, further guidance and the rationality of design are verified. To meet the increasing family care requirements, the robot multiaxial coordinated control technique is applied in nursing bed control, developed a multi-function nursing bed robotic nanomanipulation. This nursing bed through each bed panel coordination between the movement, the single move or linkage ways various pose, and through the voice or keyboard to control the movement than appearance. Nursing bed control system consists of master control module and auxiliary control module two parts. One master control module adopts single-chip microcomputer control, such already can reduce costs, and can ensure the nursing bed operation flexibility and reliability； Auxiliary control modules including speech recognition and voice playback two parts function. The actual usage proved was developed nursing bed. This paper the practicability and effectiveness of medical paper nets to share with you! Keywords: robotic nanomanipulation nursing bed； Control system； General cut； speech microcontroller Summary: now, both developed and developing countries are facing more and more serious, the problem of aging population. Old people, the physiological function of degradation due to poor health, generally consumed a lot of medical resources, increase the burden of the hospital. In every country in the world in active seek out new health service mode, providing higher quality, more reliable and more accepting and cheap health services. So the construction of modern distance monitoring system, has the very good prospects for development. This paper studies a community-oriented robotic nanomanipulation based health intelligent monitoring system of multi-function type, of the patients physiological parameters for continuous, long time, automatic, real-time detection, and the analysis and processing after realizing automatic alarm, automatic recording category, but also through the network for remote monitoring medical personnel the timely discovery of the patients progress, at any time to take necessary care and emergency measures. With the rapid development of social economy, the peoples standard of living rises ceaselessly, life expectancy rising longevity, the citys population is gradually entered the aging. According to statistics, in Chinas current population 1.32 billion, aging populations reach, and at an annual growth rate of 3.2%. One empty nester family total of all older family in some big cities, 25 8% in the larger ratio, such as Beijing, Shanghai 34% for 30%, guangzhou 34.8% in yesterday, tianjin for o. the aging of the population of social medical service system put forward higher request, and establish a community as the core of the health monitoring and disease precontrol information system has great practical significance o. elderly because the older, the body gradually reduce active, resistant to disease has decreased, and the disease in chronic diseases primarily. For chronic disease and paralytic character, besides the treatment with drugs and injection, physical way outside the nursing also indispensable. Correct and appropriate care can greatly enhance the patients body activity, reduce the complications of chronic disease. For many produced by regular medication, concerned, proper monitoring and correct nursing, need not hospitalizations. Especially for those who long for a variety of reasons impossible patients treated in hospital, the elderly and disabled people speaking, equipped with necessary nursing equipment and utensils particularly important compared to ordinary people. 癱瘓病 , chronic patients, people with disabilities and bed time longer and more long, thus developing a kind of comfortable, nursing complete function, cost-effective nursing bed, will has a broad market prospect? . At present, China is building community on public health service system, if will development of the nursing bed and community, hospital medical system connection, realize medical and nursing, health care, medical treatment, disease precontrol etc integration, can reduce the pressure, more reasonable hospital, effectively use existing resources for hospital 4. Meanwhile, through the hospitals, communities two information system establishment and connections, can greatly improve our public health event to deal with emergency response speed and processing power. In view of this, according to our social medical service development present situation and the practical demand, put forward a kind of multiaxial coordination based robot control techniques and speech recognition technology is muti_function nursing bed concept, successfully developed the robotic nanomanipulation multi-function nursing bed, and on this basis developed based on the nursing bed medical monitoring system of the club. This article mainly discusses the structure of robotic nanomanipulation nursing bed and control system are discussed. Graph one common nursing bed structure 1 robotic nanomanipulation nursing bed structure In the structure of robotic nanomanipulation nursing bed design, the main consideration the following son points: (1) the nursing bed should be able to realize all kinds of the nursing posture pose requirements； (2) all activities of bed panel swing Angle should comply with the medical care for both human comfort； and (3) nursing bed body reliability, stability and safety requirements, should accord with medical care (4) bed body size have certain space limits； (5) to consider nursing bed in the room moving simplicity and medical auxiliary devices (such as hanging liquid frame and book table) in nursing bed f: can be installed sex. The developed machine humanizing nursing bed bed surface structure as shown in figure 1 shows, to realize J, seven basic nursing bed of posture pose demands that a flat, carry back, flexor/leg, SLR, left/right turn, sitting up and solution then, seven panel is independent of each other. Through the coordination between each bed panel, using single movement or movement way to realize nursing bed linkage of all kinds of pose of posture pose. Nursing bed with corresponding bed panel action such as table l.3. Each bed panel swing Angle is as follows: the backplane (posture), o. 10 750； Backplane (left/right emancipated), o. + 65. ； The left/right hip board, O. + 75. ； Thigh board, o. A + 35. ； Crus board, a 55 o + 35. ； Solution will cover and O. A + 90. 2 Robotic nanomanipulation nursing bed of the control system in order to facilitate nursing bed of intelligent control, timely r solution of the current working state nursing bed nursing bed, upon the law to set necessary processes the number of sensors ?. By analyzing the data, sensor transmission control system can real-time understand, control panel of motion, bed of different agencies to prevent the mutual interference or ask to overshoot driven motor bed body, unnecessary casualties caused damage. Control system overall structure as figure2shows. In bed in the control mode pose posture, besides using popular keyboard buttons input methods outside, in order to facilitate the weak and sick, but also increased the speech input mode + operators through the voice commands to manipulate nursing bed. Due to the common types of control chip difficult to complete the voice commands, because the recognition of the nursing bed the control system is divided into two major modules. The first part primarily control module, it consists of a single-chip microcomputer control system structure, used to implement the nursing bed system, including the main control keyboard/voice control commands to accept the position signal and sensor input, and the output motor control signal etc, the second part as auxiliary control module, mainly for voice recognition and playback, it will come from the operators voice control command into electrical signals, then through code conversion, transported to the master control module, and accept the electrical signals to independent control module, will these control instruction convert audio signals of operator can understand. 2.1 robotic nanomanipulation nursing bed master control module master control module at runtime receive signals from the keyboard/speech recognition circuit analysis and processing signal, through, will control signal through external interface conveying to speech playback circuit, signal by voice playback circuit will be transformed into voice signal, provide voice feedback signal, make handlers understand nursing bed real-time dynamic； On the other hand, master control module according to various signal command, control different motor running, so as to realize the lot that users period nursing bed functions? . Master control module mainly include the following each subroutine: (1) keyboard input. The keyboard is nursing bed input control commands by one of the ways the keyboard input, by encoding commands sent to the primary panel by serial. (2) dc motor of the motor control. Nursing bed in accepting the keyboard or speech input signal after, started for the corresponding action to achieve nursing bed. This requires the expected function for installation in the main control panel can the nursing bed eight dc motor both the positive and negative direction of motor control. (3) sensor signal input. Position sensor motor sports location information feedback to control system, control system according to the feedback is returned to the current signal judgment motor sports location and condition, and then calling the corresponding procedure motion control 2.1.1 keyboard control circuit keyboard on the control board for user operation except r equipped with the keys outside, still configuration display the nursing bed the working state of indicator. Considering the keyboard and the communication and the main panel control cPu L / 0 mouths limited resources, so by a separate microcontroller keyboard to treat various task. Because the keyboard (2 x 6) and indicator light (8) required many I / 0 mouths resources, and chooses 89c2051 microcontroller only 15 L / 0 mouths, L/o u resources are limited, therefore in the SCM L / 0 mouths resource allocation, the single-chip computer keyboard panel serial communication between the main control board； Meanwhile, considering control cable is a certain length to increase the reliability of communication, communication, adopt the 232 level, so the hardware circuit MAx232 chips for added a convert. 2.1.2 dc motor level control of the nursing function is nursing bed by dc motor to execute, motor drive nursing bed to complete the various movements, in order to achieve various nursing pose, include: (1) the backplane elevate/drop； (2) left/right turn physique increase/decrease； (3) thigh board increase/decrease； (4) crus board increase/decrease； (5) flat open/close； bedpan (6) lie low postures realize/reset； (7) sitting postures realize/reset； (8) SLR postures realize/reset； (9) bended leg postures realize/reset. Above all appearance conversion between and finish all through eight dc motor FanZhuanLai to realize, so is the main control board must be able to receive commands to eight dc motor after on E reversal, namely can realize motor control negative in nursing bed to electrify control the hardware circuit design, for each motor has adopted two blades double throws on power control. The relay to 2.2 robotic nanomanipulation nursing bed auxiliary control module 2.2.1 speech recognition voice control technology is one of the existing control mode of advanced control mode, it is natural and convenient control mode, good affinity, the characteristics of applicability. Will voice control technology is introduced into the nursing bed under control, will greatly convenient users, particularly in those loss or partly losing activity, ability of self-dependence of patients, voice control and can help them enhance self-confidence, reduce dependence on others, add life courage and confidence in nursing bed users. The characteristics of the speech input commands, used in the study of the beauty of sENsORY company RSc364 little voice chip as recognition core chip. By training and realize Rsc364 chip speech recognition function, system L/o level is TrL level, which can be conveniently and other system for data transmission. Rsc364 chip inside integrated A speech recognition needs A variety of functions, it can complete speech recognition process of anti aliasing low-pass filter, sampling/keep, A/D conversion and voice recording Rsc364 chip in complete functions such as speech recognition task, will voice control signal output to SCM by chip Po and mouth. According to the PSc364 P1, the output state in the Lord with voice recognition chips control by A 74Lsl48 j Duan between expanding in tablet 74Lsl48 fracture, voice command input eight feet of the chip, connect Pl input mouth； Rsc364 Expansion of single chip J Gs meet in P3.2； SCM fracture P1.3 P1. O mouth and speech recognition chips J J 4 Po Po seven connections. When a voice command input, a mouth wipes the P1 output low level, Gs u lose I low-level startup microcontroller external interruption of single chip, the interrupt handlers from P1.0 P1.3 mouth when read people data. Laws 2.2.2 voice playback master control circuit, after receiving orders in control motor running, but also to voice playback son module lose J 【 J voice control signal by auxiliary control module. To the current users provide voice feedback. Speech with the main function modules put the son is: nursing bed receive user commands, in nursing bed function action before the speech information broadcast corresponding action, remind users do physical preparation, this kind of humanized design further improved nursing bed by the affinity of IsD4003_08 chip. Speech playback as the principal chip. IsI) 4003 series work pressure is 3 V, tuen mun recording a single chip 8min for 4 - time?. Chip adopt cMOs technology, containing oscillator, prevent confusion filter, Smoothing filter, audio amplifiers, since the action pixels and high-density multilevel flashing storage arrays, operation orders at through serial communication interface input. 3 robotic nanomanipulation nursing bed nursing bed robotic nanomanipulation control program control mode is a simplified robot control system startup way. After the first test nursing bed, then test each pose, switch state of each key-press test again, if one of the keys pressed nursing bed, then makes the corresponding action and start speech playback program told the operator, through the control speech recognition is like that, if speech recognition module identification, operator a directive, likewise, nursing bed complete corresponding action. 4 closing the robot multiaxial coordinated control technique is applied in nursing bed, may to the robotic nanomanipulation nursing bed. The developed under effective control of the robotic nanomanipulation nursing bed as shown in figure 4 shows, it can achieve more bits of adjustment, and USES the posture voice commands and keyboard input two modes for control, easy and flexible. Moreover, the master control module USES a microcontroller, making the system operation r. flexible reliable, low cost. Currently developed nursing bed has in some hospitals trial, reflect good. Future research will set wipes on how to further improve the flexibility, coordination and system function of human development system, etc. 機器人化 多功能 護理床 研究與探討 翻譯人 xxx 摘要： 人性化設計是現代設計的一個重要理念 ,它強調在設計產品時 從人體工學、生態學、美學等角度達到完美 ,體現了科技以人為本的思想。該護理床的設計正是基于這種理念 ,它不僅能夠?qū)崿F(xiàn)抬背、抬大腿 ,曲小腿和調整坐姿的功能 ,并將設計通過 Pro/E 三維實體建模軟件進行模擬和仿真分析 ,進一步指導和驗證設計的合理性 。 為滿足目前日益提高的家庭護理要求，將機器人的多軸協調控制技術應用于護理床的控制，研制了一種機器人化的多功能護理床該護理床通過各個床面板之間的協調運動，采用單動或聯動方式來實現各種位姿，并通過語音或鍵盤來控制進行多位姿的運動護理床的控制系統由主控制模塊和輔助控制模塊兩部分 構成其中主控制模塊采用單片機進行控制，這樣既可降低成本，又可保證護理床操作的靈活性和可靠性；輔助控制模塊包括語音識別和語音回放兩部分的功能實際使用效果證明了所研制的護理床的實用性和有效性本文由 醫學論文 網與您分享！ 關鍵詞 ：機器人化護理床；控制系統；語音識剮；單片機 概述： 目前，無論是發達國家還是發展中國家，均面臨著越來越嚴重的人口老齡化問題。老年人由于各項生理機能退化，健康狀況普遍不佳，消耗大量醫療資源，增加了 醫院的負擔。世界各國均在積極探求一種新的健康服務模式，提供更高質量、更可靠、更容易被接受且成本低廉的健康服務。因此現代遠程監護系統的構建，具有很好的發展前景。本文研究了一種面向社區的基 于 機器人化 多功能 式智能健康監護系統，用來對病人的生理參數進行連續、長時間、自動、實時檢測，并經分析、處理后實現多類別自動報警、自動記錄， 而且可以 通過網絡遠程監護便于醫護人員及時發現病人的病情變化，隨時采取必要的護理與急救措施。 隨著社會經濟的迅速發展，人民生活水平不斷提高，人口壽命不斷延長，城市人口正逐步進入老齡化據統計，在我 國現有人口中，老齡人口達 1 32 億，并且還在以每年 3 2的速度遞增其中空巢家庭占所有老齡家庭總數的 25 8，在一些大城市中該比例更大，如北京為 34，上海為 34 8，廣州為 30，天津?yàn)?36 5 “o人口的老齡化對社會醫療服務體系提出了更高的要求，建立以社區為核心的健康監控和疾病預控信息化系統具有很大的現實意義 ”o老年人由于年齡偏大，肌體的活性逐漸降低，對疾病的抵抗力日益減弱，且疾病多以慢性病為主對于慢性病人和癱瘓病人而言，除了配合藥物和針劑的治療外，物理方式的護理也必不可少正確、適當?shù)淖o(hù)理 可以大大增強患者肌體的活性，減少并發癥的產生對于許多慢性病患者而言，通過定期服藥、適當監護和正確護理，可以不必長期住院特別是對那些因種種原因不可能長期住院治療的患者、老年人和殘疾人士而言，配置必要的護理設備和用具尤為重要 “。相比于普通人，慢性病人、癱瘓病人和殘疾人士的臥床時間更長、更久，因此開發一種舒適、護理功能齊全、性價比高的護理床，將具有廣闊的市場前景 ”?目前，我國正著力于建設社區公共衛生服務體系，如果將所開發的護理床與社區、醫院醫療體系連接，實現醫療、護理、健康監護、醫療救治、疾病預控等的一體 化，可大大減輕醫院的壓力，更為合理、有效地利用現有的醫院資源 ”4同時，通過醫院、社區兩種信息化系統的建立和連接，可大大提升我國應對突發性公共衛生事件的響應速度和處理能力有鑒于此，筆者針對我國社會醫療服務的發展現狀及現實需求，提出了一種基于機器人多軸協調控制技術和語音識別技術的多功能護理床的概念，成功研制了一種機器人化的多功能護理床，并在此基礎上研制了一套基于該護理床的社醫監護系統本文主要對該機器人化護理床的結構及控制系統進行探討 圖一 常用的護理床結構 1 機器人化護理床的結構 在進 行機器人化護理床的結構設計時，主要考慮了以下兒點： (1)護理床應能夠?qū)崿F(xiàn)護理所需的各種體位的位姿要求； (2)各個活動床面板的擺動角度應符合醫療護理要求并兼顧人體的舒適性； (3)護理床床體的可靠性、穩定性和安全性要符合醫療護理要求； (4)床體的尺寸有一定的空間范圍限制； (5)要考慮護理床在房間內移動的簡易性以及醫護輔助裝置 (如吊液架和書飯桌 )在護理床 f：的可安裝性所研制的機器人化護理床的床面結構如圖 1所示，它實現 J，對護理床的 7 個基本體位的位姿的要求，即平躺、抬背、屈伸腿、抬腿、左右翻身、坐起以及解便， 7 個面板是相互獨立的通過各個床面板之間的協調運動，采用單動或聯動方式來實現護理床所需的各種體位的位姿護理床的位姿與相應的床面板動作如表 l 所示各床面板的擺動角度如下：背板 (坐姿 )， o。一十 750；背板 (左右翻身 )， o。+65。；左右臀部板， O。 +75。；大腿板， o。一 +35。；小腿板，一 55 o +35。；解便蓋板， O。一 +90。 2 機器人化護理床的控制系統為了便于對護理床進行智能控制，及時 r 解護理床的當前工作狀態，律護理床的脒身上需安置必要數目的傳感器 ”?通過分析傳感器傳輸來的數據，控制系統 可以實時了解、控制床面板的運動狀態，防止不同機構問的相互干涉或是驅動電機超調對床體、人員造成的不必要傷害控制系統的總體結構如圖 2所示在床體位姿的控制方式方面，除了采用通行的鍵盤按鈕輸入方式外，為了方便體弱病殘者，還增加了語音輸人方式 +操作者可以通過語音命令來操縱護理床由于普通類型的控制芯片難以完成語音命令的識別，岡此將整個護理床的控制系統分為兩大模塊第一部分為主控制模塊，它由一個單片機控制系統構成，用于實現護理床系統的主體控制，包括接受鍵盤語音控制命令和傳感器位置信號的輸入，以及輸出電機控制信號等 ，第二部分為輔助控制模塊，主要進行語音的識別和回放，它將來自操作者的語音控制命令轉化為電信號，然后經過編碼轉換，輸送至主控制模塊，同時接受來自主控制模塊的電信號，將這些控制指令轉換為操作者可以理解的聲音信號 2 1 機器人化護理床的主控制模塊主控制模塊在運行時接收來自鍵盤語音識別電路的電信號，經過分析處理，將控制信號通過外部接口輸送到語音回放電路，由語音回放電路將電信號轉化為聲音信號，提供語音反饋信號，使操作者隨時了解護理床的實時動態；另一方面，主控制模塊根據各種信號命令，控制不同的電機運轉，從而實現用戶 所期掣的護理床的功能 ?主控制模塊主要包括以下各子功能： (1)鍵盤輸入鍵盤輸入是護理床輸入控制