注塑常用術語英文表達

1、1.霧氣moisture streaks2.玻纖分配不均glass fiber streaks3.困氣gas trap effect4.銀絲紋sliver marks5.結合線weld line6.水波痕water wave effect7.黑點dark sport8.頂出印visible ejector marks9.變形deformation during demolding10.填充不足short filling11.冷料流痕cold slug12.進膠口點不良dull spots near the sprue13.噴射痕jetting14.表面起層flaking of the surf

2、ace layer15.浮泡entrapped air16.過熱變色burnt streaks17.龜裂stress crack18.縮水痕sink marks19.真空氣泡density bubble20.披鋒flash21.擦傷印scratch marksglass fiber rich surface/glass emergence on the surface22 尺寸過大over dimension23 尺寸過小under dimension24 翹曲warpage/warped25 收縮shrinkage/shrink26 縮影sink marks27 打不滿short shot/

3、short molding塑料模具mould of plastics注塑模具injection mould沖壓模具die模架 mould base定模座板 top clamping platetop platefixed clamp plate水口推板stripper platea 板 a plateb 板 b plate支承板support plate方鐵spacer plate底針板e(cuò)jector plate面針板e(cuò)jector retainer plate回針return pin導柱guide pin有托導套shoulder guide bush.直導套straight guide bu

4、sh動模座板 bottom clamp platemoving clamp plate基準線 datum line基準面 datum plan型芯固定板core-retainer plate凸模固定板punch-retainer plate頂針 ejector pin單腔模具single cavity mould多腔模具multi-cavity mould多澆口 multi-gating澆口 gate缺料 starving排氣 breathing光澤 gloss合模力 mould clamping force鎖模力 mould locking force擠出 extrusion開裂 crack

5、循環時間cycle time老化 aging螺桿 screw麻點 pit嵌件 insert活動鑲件movable insert起堊 chalking澆注系統feed system主流道sprue分流道 runner澆口 gate直澆口 direct gate , sprue gate輪輻澆口spoke gate , spider gate點澆口 pin-point gate測澆口 edge gate潛伏澆口submarine gate , tunnel gate料穴 cold-slug well澆口套 sprue bush流道板 runner plate排飛槽 vent分型線（面） parti

6、ng line定模 stationary mould ， fixed mould動模 movable mould, movable half上模 upper mould ， upper half下模 lower mould ， lower half.型腔 cavity凹模 cavity plate ， cavity block拼塊 split定位銷 dowel定位銷孔dowel hole型芯 core斜銷 angle pin, finger cam滑塊 slide滑塊導板slide guide strip楔緊塊 heel block, wedge lock拉料桿 sprue puller定位環

7、 locating ring冷卻通 cooling channel脫模斜度draft滑動型芯slide core螺紋型芯threaded core熱流道模具h(yuǎn)ot-runner mould絕熱流道模insulated runner mould熔合紋 weld line（ flow line ）三板式模具three plate mould脫模 ejection換模腔模具interchangeable cavity mould脫模劑 release agent注射能力shot capacity注射速率injection rate注射壓力injection pressure差色劑 colorant保壓時間holdup time閉模時間closing time定型裝置sizing system陰模 female mould ， cavity block陽模 male mould電加工設備electron discharge machining數控加工中心cnc machine center萬能鐵床 universal milling machine臥式刨床 horizontal planer車床 engine lathe平面磨床surface grinding mach