DIeband設備說明書

1、專業好文檔為您整理 謝謝使用 更多精彩內容請關注本站2.3Workholder Indexing Adjustment for SDCPThe next step is to setup the Indexer and Workholder Module which is the coresystem for substrate transfer and indexing.What will happen if indexer is not set properly?It might have serious impact on machine operation. As substrate

2、cannot be smoothly transferredto the designated position, it may lead to substrate transfer error, substrate jamming, and PRS1. Change dispense and bond anvil blockson workholder according toerror (Pattern recognition error).different package requirements.1. Adjust Bond Optics OffsetAlign bond optic

3、s center with the vacuum holecenter on anvil blockTurn the screw located at the back of bondoptics for X-direction adjustmentKey in value in Optics Offset Y-Go to : SetupIndexer & WorkholderOptics Offset YCODECOMMAND3Setup3Indexer & Workholder5Optics Offset Y專業好文檔為您整理謝謝使用 更多精彩內容請關注本站專業好文檔為您整

4、理謝謝使用 更多精彩內容請關注本站2. Adjust Track Width-Go to: SetupIndexer & WorkholderCODECOMMAND3SetupTrack Width Offset3Indexer & Workholder4TrkWid/Downset OffsetKey in values to compensate the track widthoffset after Start ConversionAlign bond pad center with optics center in Y directionso that the bond

5、 pads can be sucked firmly by the vacuum holesFine adjust position until the substrate can be moved smoothly along the track3. Adjust TBond Exchange OffsetWe adjust the Indexer Clamp and Moving WindowClamp Position by adjusting the Exchange Offset-Go to: SetupIndexer & WorkholderIndexer Position

6、sExchange OffsetTBondCODECOMMAND3Setup3Indexer & Workholder9Indexer PositionsExchange OffsetTBondNote: ToadjusttheFirstDistance,bondpads should be alignedwiththeanvilblock4. Adjust TBond First Distance-Go to: Setup Indexer & Workholder IndexerPositions First Distance DispAdjust Dispense Firs

7、t Distance by joystickCODECOMMAND3Setup3Indexer & Workholder9Indexer Positions1 First Distance1 TBondNote: ToadjusttheFirstDistance,bondpads should be alignedwith theanvil block專業好文檔為您整理謝謝使用 更多精彩內容請關注本站專業好文檔為您整理謝謝使用 更多精彩內容請關注本站5. Adjust Disp First Distance-Go to: Setup Indexer & Workholder I

8、ndexerPositions First Distance DispAdjust Dispense First Distance by joystickCODECOMMAND3Setup3Indexer & Workholder9Indexer Positions1 First DistanceNote: ToadjusttheFirstDistance,bondpads should be alignedwiththeanvilblock6. Adjust Bond Exchange OffsetWe adjust the Indexer Clamp and Moving Wind

9、owClamp Position by adjusting the Exchange Offset-Go to: SetupIndexer & WorkholderIndexer PositionsExchange OffsetTBondCODECOMMAND3Setup3Indexer & Workholder9Indexer PositionsExchange OffsetTBondNote: ToadjusttheFirstDistance,bondpads should be alignedwiththeanvilblock7. Adjust Bond First Di

10、stance-Go to: Setup Indexer & Workholder IndexerPositions First Distance BondAdjust Bond First Distance by joystickCODECOMMAND3Setup3Indexer & Workholder9Indexer Positions1 First Distance0 Bond專業好文檔為您整理謝謝使用 更多精彩內容請關注本站專業好文檔為您整理謝謝使用 更多精彩內容請關注本站i?Definition of First Distance PositionFirst Dist

11、ance position at dispense/ bond area is the position of substrate stopped at dispense/bond area respectively after indexing. It can also be interpreted as the position at whichdispensing/ bonding starts.stWhy do we have to align the 1 pad center with the center line of the anvil block?The purpose of

12、 it is to align the vacuum holes located at the anvil block with pad columns. Thismakes sure that pads can be held securely by vacuum during production.8. Adjust Track Sensor SensitivityThere are totally 4 sensors on track which are shown belowAdjust the sensitivity by 2-point methodSensorChannel Nu

13、mberInput JamChannel 1LF exist on trackChannel 2LF OrientationChannel 3Output JamChannel 4專業好文檔為您整理謝謝使用 更多精彩內容請關注本站專業好文檔為您整理謝謝使用 更多精彩內容請關注本站Turn “SW1 ” ofsensor amplifier until the targeted channel number displayed onLEDPress SW2“ ” until RUN“” is displayed and blinksTurn “SW2” until SET“” is displa

14、yed and blinksSelect 2P“” and presshet knob to accessUnblock the sensor, press SW2”“to confirm the setting until 2” is displayed“Manually put a leadframe to block the sensor, press“SW2 ” again to confirmthesettingTurn “SW2” until RUN“” is displayedPress the knob again to finish the settingNote:Manua

15、lly place a substrate to block the sensor and compare the values shown on theamplifier before and after the sensor is blocked. Positive and negative values should be notedrespectively for a proper setup9. Adjust Anvil Block Vacuum Sensor Sensitivity-Select the Channel by pressingand-Press theto edit the C1 and C2 valueWe can set the value of C1 and C2 are equal then this value will become thethreshold value for the vacuum level of anvil blockIf vacuum level is higher than that value, it will give out a HIGH signal for anvilvacuum.If vacuum level i