手搖電阻二極管成型機說明.

1、UserGuideManual,Motor Drive Vertical Mount FormerBT-100F BT-201F手動,電動帶式電子零件成型機使用說明書 深 圳 市 新 比 特 電 子 科 技 有 限 公 司Tel27349620 27382501 Faxttp:/ Email:sdx 非常感謝并恭喜您擁有本公司BT-100F手動電子零件成型機，BT-201F電動電子零件成型機。在開始使用之前，請檢查包裝中以下項目是否完整。1、 本體2、 把手3、 零件成品盒4、 帶裝零件支架安裝您的機械：1、 將手柄裝在機械本體上。2

2、、 把機械置于桌邊并固定于其上。3、 把帶裝零件固定架裝于本體的邊上（在本體之兩邊均有雙孔可選擇）4、 把成品盒置于機械的下方?，F(xiàn)在您可以開始設定您的機械了。操作程序：1、 把帶裝零件滑過進料軌道（28），并注意不要太緊，把零件本體置于成型齒輪（22）右邊（如圖Fig4）并先試彎一個看是否符合您的規格。2、 調整零件腳距先松開成型齒輪（22）上的固定螺絲，調整成型齒輪（22）與成型彎刀（23）之間的間隙，使其達到所需要的腳距（調整完后記得鎖緊固定螺絲）。3、 調整零件腳長度先松開切斷齒輪（221）上的固定螺絲，然后調整所需要的長度（調整完后記得鎖緊固定螺絲）。4、 調整零件肩高零件本體（301

3、）距離成型齒輪（22）約1mm左右，視本體大小而定，距離越大彎出來高度越高（以不傷到零件本體為原則）現在您的機械可以開始使用了BT-100F順時鐘方向轉動把手，您會看到零件成型彎腳后一個個掉入成品盒中，撿幾個檢查一下，如果規格不符，請照上述調整方式修正，如果規格符合即可正式生產。BT-201F先把調速器（162）轉到零，插上電源并打開馬達開關（161）慢慢加快調速器（162）到適當速度，并檢查成型后之規格，如符合即可正式生產。經過使用一段時間之后，如果您發現機械所切出來的腳有毛邊時，請把切斷刀（21）拆下來加以研磨，或向本公司購買備品，不要忘了定期給機械加潤滑油及清理，如有不清楚之處，請聯絡經

4、銷商或本公司客服部，我們很樂意為您服務。1Your machine comes complete with the following items in the list below.Make sure that you have evetything betore trying to set up your unit.1. Main Body2. handle3. Parts Bin4. Tape Reel Holder BaySetting Up Your Machine1. Assemble the handle to the main body 2. Put the unit alon

5、g the side of the bench and fix it onto the bench.3. Assemble the tape reel holder on the machine.There are two sets of holes on both sides of the base that you can choose to mount it.4. Put the parts bin under the machine.Now it is ready for adjustment.Operation Procedure1. Sliding the taped compon

6、ents into the plastix Feeding fuide(28),Please note to make it freely not too tight.Then engaging the lead of components to the forming wheel(22)and put the body to the right side of the forming wheel as illustrared in FIG-5.Cranking the handle to test the forming condition.2. Adjusting the Pitch of

7、 the components.Release the fised screws in the forming wheel(220,Adjusting the distamce between the forming wheel(22)and Bending Plate(23)to the desired specification(Pleasedont forget to right the screw released.)3. Adjusting the length of the components.Release the fixing screws of the cutting Di

8、sc and adjusting the distance to meet the requirement(tighten the ssrew released.)4. setting the Shoulder Height of the componentsOne(!)mm is a normal distance between the body of components to the forming wheel(22).More distance will get more height in the shoulder of the components(Basing on the p

9、rinciple of no damage of the body)Your Machine Is Ready For Running Now*100F Cranking the handle of the machine clockwise slowly.You will see some components that are cut and drop into the parts bin.Take some and check.Please re-adjusting the machine according the procedure if failed to meet specifi

10、cation.Otherwise the machine is ready for mass production.*201F Turning the speed regulator(162)to Zero(0)position before tutn on the ON/OFF Power Switch().Then increasing the speed gradually when the power is ON unat proper speed is reached.Take some of the parts formed and check the specification.

11、Re-adjusting the data according to procedure listed or the machine os ready for mass production.If the cutting edge of the lead is not good as before after a long time operation or burr is fouvd, please dismantle the cutting blade and re-sharpen it Dont forget your regular lubrication and maintenanc

12、e.If further service is needed.Please call our agent or contact us directly.2Spare Parts List零件表Part No.Description品 名14Parts Bin成品盒16Side Wall®右主機板161Power Switch電源開關162Speed Regulator調速器163Main Body圓形本體17Side Wall(L)左主機板171Bearing Ring,Main Shaft主軸培林座172Base腳座21Cutting Disc Assembly切刀210Shaft,Cutting Dise切刀軸22Forming Wheel成型齒輪221Cutting Wheel Assembly切斷齒輪222Main Shaft主軸23Bending Plate成型彎刀231Bending Plate Blick成型刀座232Screw,Bending Plate彎刀固定螺絲233Shaft,Bending Plate彎刀導桿25Frame支架26Motor馬達26AHandle把手260Motor Gear馬達齒輪261Main Shaft,Motor馬達主軸262Frame,Motor馬達支架28Feeding Guide帶裝進料軌道2