DHT11程序代碼--精選文檔

1、/現象是循環顯示溫度和濕度各顯示三秒(小數位顯示0)/若需將dht11.c和其他的硬件結合使用,只需在需用到溫濕度值的文件加下面聲明/extern int wendu, shidu;(wendu是溫度值,shidu是濕度值,比實際的溫濕度值擴大了十倍)/一、/文件名保存為main.c/*/除了dht11的接口外,其他的電路原理圖與天祥的C51板對應/現象是循環顯示溫度和濕度各顯示三秒#include "dht11.h"#include <reg52.h>sbit DULA = P26;/數碼管位定義sbit WELA = P27;static unsigned

2、char flag;/中斷計數標志static unsigned char code array= /數碼管編碼 0x3f,0x06,0x5b,0x4f,0x6, 0x6d,0x7d,0x07,0x7f,0x6f ;extern int wendu, shidu;static void InitTime(void);void Delay_1ms(unsigned int ms);static void SMG_Display(unsigned int value);int main(void) unsigned char mark = 0; /先等上電穩定 Delay_1ms(1000); /

3、因為讀一次數據dht11才會觸發一次采集數據. /即在先使用數據時采集一次數據 ReadTempAndHumi(); /因為在兩次采集數據需一定的時間間隔,這里還可減少 Delay_1ms(3000); /設定定時器 InitTime(); while(1) /三秒讀一次溫濕度 if(flag = 60) flag = 0; mark+; /* /讀溫濕度,可檢測函數調用是否失敗, /函數返回OK(1)表示成功,返回EROR(0)表示失敗 /OK和EROR是在dht11.H中定義的宏 */ ReadTempAndHumi(); if(mark % 2 = 0) /顯示溫度 SMG_Displa

4、y(wendu); else /顯示濕度 SMG_Display(shidu); return 0;/設定定時器static void InitTime(void) TH0 = (unsigned char)(65535 - 50000) >> 8); TL0 = (unsigned char)(65535 - 50000) ; TMOD = 0X01; TR0 = 1; ET0 = 1; EA = 1;/數碼管顯示函數static void SMG_Display(unsigned int value) unsigned char ge, bai, shi; ge = value

5、 % 10; shi = value % 100 / 10; bai = value % 1000 / 100; WELA = 1; P0 = 0XFE; WELA = 0; P0 = 0XFF; DULA = 1; P0 = arraybai; DULA = 0; Delay_1ms(2); WELA = 1; P0 = 0XFD; WELA = 0; P0 = 0XFF; DULA = 1; P0 = arrayshi; P0 |= 0x80; /*顯示小數點*/ DULA = 0; Delay_1ms(2); WELA = 1; P0 = 0XFB; WELA = 0; P0 = 0XF

6、F; DULA = 1; P0 = arrayge; DULA = 0; Delay_1ms(2);/中斷函數void timer(void) interrupt 1 TH0 = (unsigned char)(65535 - 50000) >> 8); TL0 = (unsigned char)(65535 - 50000); flag+;/*/ 二、保存文件名dht11.h（保存時必須命名為dht11.h）/*/*/#ifndef _dht11_H_#define _HDT11_H_/設定標志(static unsigned char status)的宏值#define OK

7、1#define EROR 0extern void Delay_1ms(unsigned int ms);/函數的返回值表示讀取數據是否成功 OK表示成功 EROR表示失敗extern unsigned char ReadTempAndHumi(void);#endif/*/*/三、保存的文件名是dht11.c/*/*/*/單片機時鐘為11.0592M#include "dht11.h"#include <reg52.h>/請根據自己的dht11接的IO口來改動位定義sbit dht11 = P20;/防止在與硬件通信時發生死循環的計數范圍#define NU

8、MBER 20#define SIZE 5static unsigned char status;/存放五字節數據的數組static unsigned char value_arraySIZE;/*可在其他的文件引用溫濕度值,實際是溫度的整數的10倍如dht11讀回的溫度是26,則wendu = 260, 濕度同理*/int wendu, shidu;static unsigned char ReadValue(void);extern void Delay_1ms(unsigned int ms) unsigned int x, y; for(x = ms; x > 0; x-) fo

9、r(y = 124; y > 0; y-); static void Delay_10us(void) unsigned char i; i-; i-; i-; i-; i-; i-;/*讀一個字節的數據*/static unsigned char ReadValue(void) unsigned char count, value = 0, i; status = OK; /設定標志為正常狀態 for(i = 8; i > 0; i-) /高位在先 value <<= 1; count = 0; /每一位數據前會有一個50us的低電平時間.等待50us低電平結束 wh

10、ile(dht11 = 0 && count+ < NUMBER); if(count >= NUMBER) status = EROR; /設定錯誤標志 return 0; /函數執行過程發生錯誤就退出函數 /26-28us的高電平表示該位是0,為70us高電平表該位1 Delay_10us(); Delay_10us(); Delay_10us(); /延時30us后檢測數據線是否還是高電平 if(dht11 != 0) /進入這里表示該位是1 value+; /等待剩余(約40us)的高電平結束 while(dht11 != 0 && coun

11、t+ < NUMBER) dht11 = 1; if(count >= NUMBER) status = EROR; /設定錯誤標志 return 0; return (value);/讀一次的數據,共五字節extern unsigned char ReadTempAndHumi(void) unsigned char i = 0, check_value = 0,count = 0; EA = 0; dht11 = 0; /拉低數據線大于18ms發送開始信號 Delay_1ms(20); /需大于18毫秒 dht11 = 1; /釋放數據線,用于檢測低電平的應答信號 /延時20-

12、40us,等待一段時間后檢測應答信號,應答信號是從機拉低數據線80us Delay_10us(); Delay_10us(); Delay_10us(); Delay_10us(); if(dht11 != 0) /檢測應答信號,應答信號是低電平 /沒應答信號 EA = 1; return EROR; else /有應答信號 while(dht11 = 0 && count+ < NUMBER); /等待應答信號結束 if(count >= NUMBER) /檢測計數器是否超過了設定的范圍 dht11 = 1; EA = 1; return EROR; /讀數據出錯

13、,退出函數 count = 0; dht11 = 1;/釋放數據線 /應答信號后會有一個80us的高電平，等待高電平結束 while(dht11 != 0 && count+ < NUMBER); if(count >= NUMBER) dht11 = 1; EA = 1; return EROR; /退出函數 /讀出濕.溫度值 for(i = 0; i < SIZE; i+) value_arayi = ReadValue(); if(status = EROR)/調用ReadValue()讀數據出錯會設定status為EROR dht11 = 1; EA = 1; return EROR; /讀出的最后一個值是校驗值不需加上去 if(i != SIZE - 1) /讀出的五字節數據中的前四字節數據和等于第五字節數據表示成功 check_value += value_arayi; /end for /在沒用