電氣儀表工程安裝調試記錄文稿

1、 表H-421母線安裝記錄Bus installation record項目：Project裝置：Unit工號：Section名稱Name施工日期Date電壓等級VoltagekV圖號Drawing No.母線型號、規格Bus model and spec.套管、絕緣子型號Bushing insulator model1、一般安裝檢查：General installation inspection序號No.檢查調整項目Inspection and adjustment item安裝檢查結果Inspection result1母線型號、規格、材質核對Bus model, spec, and ma

2、t. Inspection型號 規格 材質 Model Specification Material2絕緣子、穿墻套管檢查Insulator and lead-in insulator型號規格 油位、密封絕緣 Model Oil level, seal Insulation3母線支架制作安裝Bus support fabrication and installation規格 安裝尺寸 防腐 Spec. Dimension Anti-corrosion4母線安裝檢查Bus installation排列、相色 彎曲倍率 伸縮節 Arrangement, color Curve radius Exp

3、ansion joint5連接螺栓、墊圈檢查Bolt and washer inspection規格 熱鍍鋅 露出長度 Spec. Galvanization Left length6母線接觸面Bus contact area inspection光潔平整 搪錫 電力復合脂 Smooth. Enam. Polymer7硬母線焊接檢查Rigid bus welding inspection焊工合格證號Weldor No.8軟母線、組合母線安裝Flexible and bine bus installation2、母線接觸面連接緊密檢測：Bus contact. Tightness inspect

4、ion螺栓規格（mm）Bolt spec.實測力矩值（N.m）Actual torque螺栓規格（mm）Bolt spec.實測力矩值（N.m）Actual torque螺栓規格（mm）Bolt spec.實測力矩值（N.m）Actual torque最小值Min.最大值Max.最小值Min.最大值Max.最小值Min.最大值Max.3、軟母線弛度：Flexible bus sag inspection軟母線名稱Flexible bus name設計弛度（mm）Design sag實測弛度（mm）Actual sag4、母線相同、對地最小距離檢測：Bus phase and phase to

5、earth min. Distance measure母線類別Bus type主母線Main分支母線Branch實測最小相間距離（mm）Min. Phase to phase distance實測最小對地距離Min. Phase to earth distance備注：Remarks結論：Conclusion技術負責人Check施工人Operator表H-422蓄電池充（放）電記錄Storage battery charging/Discharging record項目：Project裝置：Unit工號：Section名稱Name型號Model出廠日期Manuf. Date電壓VoltageV

6、容量capacityAh電池總數Number of battery電解液Electrolyte電解液化驗單或合格證號Electrolyte report or certification No.蒸餾水化驗單或合格證號Distilled water report or certification No.注入時電解液溫度Electrolyte temp. at filling電解液比重Specific gravity of electrolyte開始注入時間Filling start time結束時間End time初充電First charging充電開始時間Charging start tim

7、e結束時間End time單獨補充充電的電池編號Separately charged cell No.放電Discharging放電開始時間Discharge start time結束時間End time放電電流Discharge current放電容量Discharging capacity為額定容量的%（換算到25時）% of rated capacity （at 25）充（放）電特性曲線圖：（充放電記錄見附表）Charging/Discharging characteristic curve備注：Remarks結論：Conclusion技術負責人Check施工人Operator表H-42

8、3蓄電池充（放）電記錄附表Attached table for storage battery charging/Discharging record項目：Project裝置：Unit工號：Section名稱Name型號Model出廠日期Manufacture date電壓VoltageV容量CapacityAh電池總數Number of battery時間Time充（放）電電壓（V）Charge/Discharge voltage充（放）電電流（A）Charge/Discharge currentNoNoNoNoNoNoUDTUDTUDTUDTUDTUDT技術負責人Check施工人Opera

9、tor日期Date表H-424電機抽芯檢查記錄Motor loose-core inspection record項目：Project裝置：Unit工號：Section名稱Name位號Tag. No.檢查日期Inspection Date型號Type額定容量Rated capacitykW額定電壓Rated voltagekV額定電流Rated currentA接法Connection絕緣等級Insulation class轉速Rotation speedr/min轉子結構Rotor structure防爆等級Explosion proof class出廠編號Manufacturer No.制

10、造廠Manufacturer防護等級Prevention class檢 查 容Installation contents標記Mark備 注Remark鐵芯軸頸無傷痕銹蝕No Damage & corrosion on surface of core shaft滑環和換向器無傷痕、銹蝕No Damage & corrosion on surface of mutator and slip-ring 繞組絕緣層完好，綁線無松動Winding insulation coating and fixing inspection繞組連接正確，焊接良好Winding connection a

11、nd welding inspection繞組電阻檢測合格Winding resistance inspection定子槽楔無斷裂凸出及松動，端部槽楔牢固Stator slot wedge inspection轉子平衡塊緊固，平衡螺絲鎖車Rotor balance block and bolt fixing inspection風扇完好，方向正確Fan inspection磁極及鐵軛固定良好Magnetic pole and hub fixing inspection勵磁繞組緊固Exciter winding fixing inspection 鼠籠式電機轉子導電條和端環焊接良好，澆鑄無裂紋R

12、otor conductor and end link of squirrel-cage motor軸承滾動體與、外圈轉動靈活無松動、卡澀Bearing rotating flexibility inspection加入軸承的潤滑脂已填滿部空間的三分之二Internal space of bearing is filled with lubrication grease電機機部清潔無雜物Motor internal cleanliness inspection結論：Conclusion技術負責人Check施工人Operator表H-425電機干燥記錄Motor drying record項目：

13、Project裝置：Unit工號：Section名稱Name位號Tag. No.干燥日期Drying Date型號Type額定容量Rated capacitykW絕緣等級Insulation class定子電壓Stator voltageV轉子電壓Rotor voltageV制造廠Manufacturer定子電流Stator currentA轉子電流Rotor currentA出廠日期Manuf. Date接線Connection轉速Rotation speedr/min出廠編號Manufacturer No.干燥方法簡述Brief discription of drying method干燥

14、開始時間Drying start time 年 月 日 時 分Date干燥結束時間Drying end time 年 月 日 時 分Date干燥過程最高溫度Max. drying temp.定子 Stator轉子 Stator干燥后絕緣電阻及吸收比Insulation resistance and absorptance after drying.測試部位Test position定子對地Stator to earth轉子對地Rotor to earth電機溫度（）Motor temperatureR15"（M）R60"（M）KR15"（M）R60"（M

15、）K備注：Remarks結論：Conclusion技術負責人Check施工人Operator表H-426電機干燥記錄附表Attached table for motor drying record項目：Project裝置：Unit工號：Section時間Time溫度（）Temp.定子絕緣電阻（M）Stator ins. resistance轉子絕緣電阻（M）Rotor ins. resistance干燥電流（A）Drying current備注Remark123456測溫點位置：nTemp. measure position1. ;2. ;3. ; 4. ;5. ;6. ;技術負責人Check

16、施工人Operator日期Date表H-427電機試車記錄Motor test run record項目：Project裝置：Unit工號：Section序號No.電機名稱或位號Motor name or tag. No.額定數據Rated data試車記錄數據Test run record data環境溫度（）Envi-ronment temp.試車日期Date容量(kW)Capa-city電壓(V)Vol-tage電流(A)Curr.絕緣等級Ins. class絕緣電阻(M)Ins. resis.電壓(V)Vol-tage空載電流(V)Vol-tage負載電流(A)No-Load curr

17、.電機溫度(A)Motor temp.軸承溫度（）Bearing temp.前Front后Rear備注：Remarks結論：Conclusion技術負責人Check施工人Operator表H-428架空線路施工記錄Overhead line stringing record項目：Project裝置：Unit工號：Section線路名稱Line name施工日期Date線路電壓Voltage線數Line number線路長度Length線路起點Start place線路終點End place施工記錄Stringing record電桿型號、規格及數量Pole model, spec. Quant

18、ity拉線材料及組數Stay material and quantity導線型號及規格Line model and spec.路燈型號及數量Road lamp model and quantity絕緣子型號及規格Insulator model and spec.路燈線型號及規格Toad line model and spec.弛度Sag耐桿號（號一號）Anchor pole (No. No.)設計弛度（mm）Design sag實測馳度（mm）Real sag環境溫度（）Environment temp.對地、交叉跨越距離測量：Line to earth and to cross-over o

19、bjects distance measurement跨越桿號號一號Cross-over pole No.-N0.被跨越物名稱Cross-over object name被跨越物對最近桿、塔的水平距離（m）The nearest distance between crossover object and pole導線對被跨越物的最小垂直距離（m）Min. Vertical distance from line to cross-over object溫度（）Temp.線中絕緣電阻（M）Line insulation resistanceAB，C，E，OBA，C，E，OCA，B，E，O相位檢查P

20、hase sequence inspection備注：Remarks結論：Conclusion技術負責人Check施工人Operator表H-429避雷、接地裝置安裝記錄Lightning conductor and earthing device installation record項目：Project裝置：Unit工號：Section名稱Name施工圖號Drawing No.1.繪圖或簡述避雷及接地裝置情況（種類、材質、規格、長度、埋入深度、數量、連接方法、尺寸及防腐等）Drawing or brief discription of the lightning conductor and

21、 earthing device (kind, material, specification, buried length, quantity, connection, dimension and anti-corrosion, etc.)2.接地電阻測量記錄Grounding resistance measurement record序號No.測試位置Measure position接地電阻（）Ground. resistance試驗日期Measure date當天及三天前天氣情況Weather of the day and three days ago備注：Remarks結論：Concl

22、usion技術負責人Check施工人Operator試驗人Tester表H-430電氣安裝記錄Electrical installation record項目：Project裝置：Unit工號：Section技術負責人Check施工人Operator表H-431交流電機試驗報告AC Motor test report項目：Project裝置：Unit工號：Section名稱Name位號Tag. No.試驗日期Test Date額定容量Rated capacity（kW）型號Model出廠編號Manuf. No.絕緣等級Insulation class定子電壓Stator voltageV定子電

23、流Stator currentA額定轉速Rated rpmr/min接線方式Connect mode轉子電壓Rotor voltageV轉子電流Rotor currentA相數Phase number防爆等級E. P. class直流電阻測量DC Resistance measure 溫度Temp. 定子繞組相別Stator phase直流電阻（）DC Resistance轉子繞組相別（）Rotor phase直流電阻（）DC Resistance各相直流電阻差別DC Resistance deviation定子Stator %;轉子Rotor %;定子繞組極性Stator wind, pol

24、ar.絕緣試驗Insulation test繞組名稱Wind name絕緣電阻（M）Ins. resis吸收比Absorp-tance交流耐壓電壓（kV）AC Withstanding voltage時間（mm）Time直流耐壓電壓（kV）DC Withstanding voltage時間（mm）Time直流泄漏電流（A）DC Leakage current定子繞組Stator wind轉子繞組Rotor wind電機軸承絕緣電阻（M）Bearing ins. resistance附屬設備檢查Auxiliary device test設備名稱Device name絕緣電阻（M）Insulati

25、on resistance直流電阻（）DC Resistance起動電阻器Start-up resistor可變電阻器Variable resistor滅磁電阻器Magnetic extinguisher備注：Remarks結論：Conclusion技術負責人Check試驗人Operator表H-432直流電機試驗報告DC motor test report項目：Project裝置：Unit工號：Section名稱Name位號Tag. No.試驗日期Test Date額定容量Rated capacitykW型號Model出廠編號Manuf. No.勵磁方式Excite mode額定電壓Rate

26、d voltageV額定電流Rated currentA額定轉速Rated rpmr/min工作率Work ratio勵磁電壓Excite voltageV勵磁電流Excite currentA1.試驗與檢查Test and inspection 環境溫度：Environment temp. 勵磁繞組的絕緣電阻及交流耐硬度試驗Excite wind. Ins. R & AC withstanding voltage testMkV min電樞的絕緣電阻及交流耐壓試驗Armtr. Ins. R & AC withstanding voltage testMkV min勵磁繞組的直

27、流電阻Excite wind DC resistance電樞整流片間的直流電阻Armtr. Back-to-back DC resistance勵磁可變電阻器的直流電阻DC R of Excite variable resistor繞組極性及其接線檢查Wind. Polar. & connection碳刷位置檢查Bruch position inspection2.發電機的空載特性Generator no-Load characteristics勵磁電流（A）Excite current電壓（V）Voltage備注：Remarks結論：Conclusion技術負責人Check試驗人Op

28、erator表H-433變壓器試驗報告Transformer test report項目：Project裝置：Unit工號：Section名稱Name位號Tag. No.試驗日期Test Date額定容量Rated capacitykVA型號Model出廠編號Manuf. No.接線組別Connection額定電壓Rated voltagekV額定電流Rated currentA阻抗Resistance%冷卻方式Cool. mode直流電阻測量：AC Resistance measure 溫度： Temp. 高壓側HV side（）（）（）（）（）低壓側LV side電阻（）Resistanc

29、eAaBbCc誤差 %Error變壓比檢查：Transformer rate inspection分接開關位置Tap position標稱變比Nominal rate高壓側電壓/低壓側電壓HV/LV實測變壓比Real rate變壓比誤差（%）Rate errorUAB/Uab（V）UBC/Ubc（V）UCA/Uca（A）ABBCCAABBCCA絕緣試驗：Insulation test項 目Item絕緣電阻及吸收比Ins. R and Absorbt R60"/R15"交流耐壓試驗AC withstanding voltage test直流泄漏試驗DC leakage tes

30、t介質損失角正切值Loose tgR60"/R15"吸收比Absorb-tance電壓（kV）Voltage時間（min）Time電壓（kV）Voltage電流（A）Currenttg（%）溫度（）Temp.高壓低壓及地HVLV/Earth低壓高壓及地LVHV/Earth絕緣油試驗：油號#；五次擊穿電壓平均值：kVIns. Oil test: oil No. , average voltage for 5 break down is接地組別或極性檢查Connection inspection備注：Remarks結論：Conclusion技術負責人Check試驗人Operat

31、or表H-434斷路器試驗報告Circit breaker test report項目：Project裝置：Unit工號：Section名稱Name位號Tag. No.試驗日期Test Date型號Model額定電壓Rated voltagekV額定電流Rated currentA開斷電流M. currentkA操動機構型號Operation mechanism操作電壓Oper. voltage出廠編號Manuf. No.導電回路直流電阻測量DC Resistance of primary circuit真空斷路滅弧室真空度檢查Vacuum insp. for vacuum breaker六氟

32、化硫斷路器氣體壓力Gas press. Insp. for SF6 breaker相別Phase主觸頭（）Main contact滅弧觸頭（）Arc-Extinguishing contact相別Phase電壓（kV）Voltage時間（min）Time相別Phase壓力（Mpa）PressureAAABBBCCC機械特性：Mech. Characteristic最低合閘電壓Min. close voltage最低分閘電壓Min. openn voltage合閘時間Close time分閘時間Open time合閘時間Close time分閘時間Open timeVVssm/sm/s線圈試驗：

33、Coil test絕緣試驗：Insulation. Test項目Item合閘接觸器Close contact合閘線圈Close coil分閘線圈Open coil相別Phase絕緣電阻（M）Ins. resis.交流試驗電壓（kV）AC test voltage時間（min）Time直流電阻DC Resis.AB絕緣電阻Ins. resis.MMMC斷路器在額定操作電壓下分合閘次，動作良好。Breaker open/closetime with rated oper, voltage and operate well絕緣油五次擊穿電壓的平均值：Average voltage for 5 bre

34、aking down iskV備注：Remarks結論：Conclusion技術負責人Check試驗人Operator表H-435電力電纜試驗報告Power cable test report項目：Project裝置：Unit工號：Section名稱Name試驗日期Test Date規格型號Spec./Model額定電壓Rated voltagekV長度Lengthm中間頭數Number of connection電纜起點Start point電纜終點End point絕緣電阻Insulation resistance相別PhaseABBCCAAEBECE絕緣電阻（M）直流耐壓及泄漏電流DC

35、withstanding voltage and leakage current試驗電壓（kV）Test voltage時間（min）Time泄漏電流Leak, curr.（A）AB，C，EBC，A，ECA，B，E相位檢查Phase inspection備注：Remarks結論：Conclusion技術負責人Check試驗人Operator表H-436電壓互感器試驗報告P T test report項目：Project裝置：Unit工號：Section名稱Name位號Tag. No.額定電壓Rated voltageV/V；V型號Model接線線別Connection準確等級Precision

36、容量CapacityVA最大容量Max. Cap.VA制造廠Manufacturer出廠編號Manuf. No.A相No.Phase AB相No.Phase BC相No.Phase C試驗日期Test date相別Phase絕緣電阻R60" R15"Insulation resistance交流耐壓AC withstanding. Voltage.介質損耗Loose tg一次對二次，輔助及地（M）Pri. To sec., Aux. and E.二次對一次，輔助及地（M）Sec. To pri., aux. and E.輔助對一次，二次及地（M）Aux. To pri. , sec. and E.電壓（kV）Voltage時間（min）Timetg（%）溫度（）Temp.ABC繞組直流電阻 溫度Wind DC R Temp.絕緣油擊穿電壓Oil break down voltage接線組別或極性檢查Connection inspection相別Phase一次線圈（）Primary coil相別Phase五次平均值（kV）Average for 5 timesABC變壓比檢查Tra