臨時用電方案(中英文)

1、道康寧（張家港）有限公司19萬噸/年有機硅聚硅氧烷項目（二期）Dow Corning 190kt/a Siloxane Project in Zhangjiagang (phase 2)(Team A區Part A& C鋼結構安裝工程)（steel structure installation engineering for Part A& C of Team A area）臨時用電方案Temporary Electricity Supply Plan編制Author: 審核Verifier: 批準Approver: 上海寶冶建設有限公司Shanghai Baoye Const

2、ruction Corp.Ltd一、 編制說明道康寧有機硅聚硅二期鋼結構工程Team A區鋼結構工程基本上全部為高強螺栓連接，現場臨時用電主要是用于極小量的焊接及打磨、飲水機等少量用電設施，計劃用電總功率約26KW。一級電箱不用配備（已與業主聯系用博格豪森路與12區之間的配電箱編號為63）。配備一個二級電箱，多個移動式小配電箱（主要是用于砂輪機）。具體電箱布置及電纜走向見電箱布置及電纜走向圖。Team A steel structure in Dow Corning Siloxane Project Phase 2 is mainly connected with high strength

3、bolt. In allusion to all construction use of power operated tools, welding machine, rotary sander, the planning for total power is about 26KW. It should not fit out the main electrical distribution container (it will use the distribution container which located between Bogehaoshen road and area 12,t

4、hat the number is 63)。It should fit out the secondary panel and many mobile distribution panels (mainly for rotary sander). Arrangement of distribution container and routing of cable meet the following schematic plan.二、電源配置走向示意圖：低壓配電的操作順序如下，送電順序：業主提供的一級電源箱寶冶二級電源箱開關箱；停電順序相反。The electrical sequence: t

5、he main distribution containerSBCs distribution container switch box;三、電纜、電箱的配置所有電箱、電纜均以“三相五線制，三級配電二級保護，一機、一閘、一漏、一箱”的原則進行配置。All distribution boxes and cables should apply three-phase five-wire system, with three class power distribution and two-step earth-fault protection. One machine can only conne

6、cts to one switch, one leakage protection equipment and one distribution container. 四、安全用電措施 security electricity supply measure1）、電工必須經專業技術培訓合格后方可進入現場進行施工。電工必須持有操作證上崗作業，嚴禁無證上崗作業。Electrician should take part in the training and be approved by the owner and engineering should have the certificate to

7、work.2）、所有進現場的配電箱、配電線、電纜、用電設備，必須預先經過檢驗、測設，合格后方可使用。不得采用殘缺、破損等不合格產品。All approach distribution, wire, cable and electricity supply equipment should pass the inspection and test. It should not allow use the sub-quality products.3）、用電系統必須按規范規定設置短路、漏電保護。 The electricity supply system should accord with th

8、e specification to set up the cutting-out and protection for leakage.4）、配電裝置必須設端正、牢固，不得拖地放置；周圍不得有雜物、雜草；進線端必須做固定連接，不得用插座、插頭做活動連接；進出線上嚴禁搭、掛、壓其它雜物。The distribution device should set up the correctitude and firm, it should not lay-aside on the ground; the round of the distribution device should not have

9、 the natural grass and sundries; it should firm lead-in end, it should not move the connection with the plug and attachment plug. The sundries should not allow hung and press on the wire.5）、移動式配電裝置及用電設備遷移位置時，必須先將其前一級電源隔離開關分閘斷電，嚴禁帶電搬運。When portable-type distribution device and the electricity supply

10、equipment move the location, it should switch off. 6）、用電設備嚴禁濺水、浸水，已經濺水或浸水的用電設備必須停電處理，未斷電時，嚴禁徒手觸摸和打撈。Splashing water and water strictly prohibited on the equipment, the equipment which already has the splashing water and water should switch off the power to deal with the water. Touch and fishing stri

11、ctly prohibited when the power is on.7）、建立技術交底制度及相應的檔案，通過技術交底提高各類人員安全用電意識和水平。建立電氣巡查、維修、拆除制度。It should establish the system for technique hand-over and relative fire to improve the consciousness of electricity supply. It should establish the system for go on a tour, maintain and dismantle.8）、動火或動電焊前應

12、對周圍環境進行檢查，如發現有易燃、易爆或電纜、光纜等敏感性物質應進行有效保護方可進行。It should be checked the surrounding environment before weld. It found the explosive, cable, fiber optic cable, ect. It should be protected to work.9）、，電焊專業人員進入作業現場，作業人員一定要穿戴好防護用品并應戴好防護鏡或防護面罩。When entry in the site, the worker should wear the protection goo

13、ds, the welder should wear the protective glasses and protective mask.10）、焊機接地要良好，防止觸電事故發生The welder earth in good condition, it should prevent the accident for electroshock.11）、焊接完后及時關閉焊機，將焊鉗放在絕緣物品上或懸掛起來，不得與構件接觸。It should switch off the weld machine; the welding tongs should put on the insulator or

14、 hang on. Dont touch the member.12)、作業區內必須配有可撲滅電器火災的滅火器，作業區不得有易燃、易爆物品，防止火災等發生。It should equip with annihilator, it should not have the tinder to prevent the fire.13）、施工場地注意文明施工，安全通道暢通，電焊線堆放整齊，保證施工現場的整潔。It should attend the civilization construction. The members and construction material should pile regular. It should clean the rubbish and keep the orderliness on site.14）配電箱、開關箱要合理設置，避免不良環境因素?fù)p害和引發電氣火災，其裝設位置應避開污染介質、外來固體撞擊、強烈振動、高溫、潮濕、水濺，以及易燃易爆物The configuration of distribution box and switch box should be suitable. Avoid damage and fire