




版權說明:本文檔由用戶提供并上傳,收益歸屬內容提供方,若內容存在侵權,請進行舉報或認領
文檔簡介
1、該文檔是極速PDF編輯器生成,如果想去掉該提示,請并:MMC 的信息與使用SIEMENS A&D CS 2004-3-10首先我們建議您siemens A&D 公司的技術支持:www4.ad.siemens.de或問題的 關鍵字 ,獲取關于在檢索窗口中鍵入相關或問題的詳細信息和手冊。圖 1 您可以在 www4.ad.siemens.de的檢索窗口中鍵入 MMC 等關鍵字 ,獲取關于MMC、PG 或(USB prommer)等的相關信息。MMC 卡是西門子新型 PLC 的程序、數據的體,目前應用于以下幾種 PLC:訂貨號名稱新型CPU 314新型CPU 315-2DP6ES76ES76ES76E
2、S76ES76ES76ES76ES76ES7314-1AF10-0AB0315-2AG10-0AB0312-5BD00-0AB0313-5BE00-0AB0313-6CE00-0AB0313-6BE00-0AB0314-6CF00-0AB0314-6BF00-0AB0613-1CA00-0AE3CPU CPU CPU CPU CPU CPU312C313C313C-2DP313C-2PTP314C-2DP314C-2PTPC7 613該文檔是極速PDF編輯器生成,如果想去掉該提示,請并:6ES76ES76ES7635-2EC00-0AE3635-2EB00-0AE3151-7*-0AB0C7
3、635 OPC7 635 OPET200S with CPU軟硬件的升級略有調整,注:以上的訂貨號會因為特性以名稱為準。1 在定購以上時,PLC 本身不帶有 MMC 卡,所以為了正常使用 PLC,您必須根據您工程項目實際需求定購一個大小適用的 MMC 卡,如果您的 PLC 上未MMC 卡,你是無法將 STEP7 中的數據下去的,同時你應當注意,不能帶電插拔MMC 卡,否則會丟失程序或損壞 MMC 卡。2 在 Simatic manager 中,選擇一個程序塊,則該塊被到 MMC 卡中,如果在窗口左邊的圖中選中 Block 文件夾進行,則所有的塊被到 MMC 卡上,MMC 中原有的信息將被覆蓋,
4、向MMC 卡讀寫數據或程序的次數不受限制。3 除過 CPU 中集成的 SFB/SFCs 塊外,MMC 當中其他的塊可被刪除。4 對某些 CPU 用新版 MMC 卡(6ES7 953-10-0AA0)替代舊版 MMC 卡(6ES7 953-00-0AA0)時需要升級 PLC 的 OPERATING SYSTEM。升級時需要使用 PG(6ES7798-0BA00-0XA0)或帶 USB 口的編程器(6ES7792-0AA00-0XA0),通過 STEP7 MANAGER 窗口中的菜單功能“PLC/UPDATE OPERATING SYSTEM”將 CPU_HD.UPD 文件寫到 MMC 卡上,CP
5、U_HD.UPD 文件可以在 www4.ad.siemens.de上得到。5 MMC 卡作為 CPU 的裝載內存(Load Memory),在為您的 CPU 選型 MMC 的時候,我們建議您所選的 MMC 卡一定要大于等于您所選定的 CPU 工作內存的大?。╳ork memory),最好比工作內存大一些,但如果您的應用中,PLC 工作時要使用大量的過程數據,歷史數據,配方數據等或工藝中存在較多的用戶程序塊、STEP7 中的應用功能塊(如FB41、FB42 等)時,建議選用 28M 的 MMC 卡,但請注意只有 314、3152DP、C7 系列的 PLC 支持 8M 的 MMC 卡。6 MMC
6、卡是裝載內存,所以不能夠在上位機中的組態軟件中直接MMC 卡上的數據值(DB 塊中的數據),組態畫面7 在西門子的 PLC 上必須使用西門子的是 PLC RAM 內存中的數據。的 MMC 卡,如下表中所列出的,不能使用數碼相機、移動或 PDA 等數碼使用的通用型MMC 卡。The order numbers for MMC cards are in the followingtable:MMC 常見問題列表QUESTION 1 : 如何確定 STEP7 中的工程項目需要使用多大空間的 MMC 卡?QUESTION 2 : MMC 卡上程序塊或數據塊的限制是什么?Micro Memory Car
7、d / S7-300Order number64 Kbytes6ES7 953-8LF11-0AA0128 Kbytes6ES7 953-8LG11-0AA0512 Kbytes6ES7 953-8LJ11-0AA02 Mbytes6ES7 953-8LL11-0AA04 Mbytes6ES7 953-8LM11-0AA08 Mbytes6ES7 953-8LP11-0AA0該文檔是極速PDF編輯器生成,如果想去掉該提示,請并:QUESTION3:如何刪除 MMC 卡上的數據或程序?QUESTIONMMC?4:31X 型 PLCMMC 卡后,STOP 燈不停閃爍,怎么辦? 或 如何格式化QUE
8、STION5:MMC 卡的 S7300 PLC 不能正常調用 SFC54 程序塊?QUESTION的?6:采用 MMC 卡的 S7300 和 C7613,635 系列 CPU 是如何完成數據保持功能QUESTION7:我如何將一些系統文件或是項目相關的文件到 MMC 上?QUESTION8:將STEP7 項目完整地保存在 MMC 卡上,該選擇多大的 MMC?QUESTION對 MMC9:我對MMC 卡的 S7300PLC 進行了加密,但我忘記了,如何才能,或刪除 MMC 卡上的?QUESTION 1 : 如何確定 STEP7 中的工程項目需要使用多大空間的 MMC 卡?Answer :確定您的
9、程序所需的MMC 卡的大小,可以按以下步驟進行:1. 在 STEP7 Manager 中打開您的 Project;2. 選中您的程序塊,點擊鼠標右鍵(或快捷鍵 Alt + Enter),打開程序塊的屬性頁面:該文檔是極速PDF編輯器生成,如果想去掉該提示,請并:3 選擇彈出窗口中的 General-Part 2 頁面:從上圖中可以看出您的某個程序塊在PLC 中占用裝載內存和工作內存的字節數。4 將您項目中所有程序塊(OB、FC、FB、DB)占用裝載內存(Load Memory Requirement)的數量加在一起:該文檔是極速PDF編輯器生成,如果想去掉該提示,請并:這里的 OB1 程序塊需
10、要占用裝載內存(即 MMC 卡)中的 248 個字節。這里的 FB101 程序塊需要占用 MMC 卡中的 4490 個字節。將 OB、FB、FC、DB(不包括 SFC、SFB、System data)所需占用的字節數加在一起:該文檔是極速PDF編輯器生成,如果想去掉該提示,請并:得到的總的字節數量在除以 1024,就可以知道您的 Project 中的程序塊需要多大的 MMC 卡空間。5 如果您已經有 Siemens 的 PLC 和 MMC,那么您可以通過裝載內存(MMC 卡)的使用情況。診斷,獲取 PLC 工作內存和在 STEP7 Manager 界面中,選中 CPU,用 CP5611 或PC
11、-Adapter 連接 PLC 的 MPI 通訊口,使用快捷鍵 Ctrl + D,彈出 PLC 的診斷信息窗口:當 MMC 卡未PLC 中時:因為 PLC 中沒有MMC 卡,Load memory RAM + EPROM 列為空,Work Memory 列中顯示當前 PLC的工作內存為 48K,EPROM 是 S7-400、舊款 S7-300 使用的裝載內存卡;在 PLC 中MMC 卡時,使用快捷鍵 Ctrl + D 彈出 PLC 的內存使用情況:該文檔是極速PDF編輯器生成,如果想去掉該提示,請并:可以看出 PLC 的內存使用情況為 0,空余 128K 裝載內存和 48K 工作內存;將您的程
12、序到PLC 當中:使用Ctrl + D 彈出 PLC 的內存使用情況:該文檔是極速PDF編輯器生成,如果想去掉該提示,請并:可以看出,您的程序在PLC 中對裝載內存和工作內存的占用情況。返 回QUESTION 2 : MMC 卡上程序塊或數據塊的限制是什么?Is there any restriction to the number of blocks I can load onto an MMC (Micro Memory Card)?ANSWER:Yes, there issize as showna limited number of blocks you can load onto a
13、n MMC depending its by the table below:Table 1:um number of blocks on an MMCTypeMLFBum number of blocksMMC 64KB6ES7953-8LF11-0AA0768MMC 128KB6ES7953-8LG11-0AA01024MMC 512KB6ES7953-8LJ11-0AA02560MMC 2MB6ES7953-8LL11-0AA06528MMC 4MB6ES7953-8LM11-0AA012672該文檔是極速PDF編輯器生成,如果想去掉該提示,請并:Please note here the
14、 applicable quantity framework for each CPU (number of blocks altogether).返 回QUESTION 3 : 如何刪除 MMC 卡上的數據或程序?How can I delete the data or program on a MMC (Micro Memory Card)?You can use the following procedure tete the block on an MMC in the CPU:1.2.The MMC to be deleted is slotted in the CPU.In the
15、 SIMATIC Manager, switch to online mode via View Online or by pressing the appropriate button.In the Online window, you select the block folder.Select all the blocks in the folder which you want tete.Click the Delete key on your PC keyboard (you can acknowledge the message that system functions cann
16、ot be deleted).3.4.5.返 回QUESTION 4 : 31X 型 PLCMMC 卡后,STOP 燈不停閃爍,怎么辦? 或 如何格式化MMC?Why does the STOP LED flash on my CPU 31xC when the MMC (Micro Memory Card) isslotted? The CPU does not behave like this with other MMCs.ANSWER:The MMC in your CPU is not formatted or contains data that cannot be interpr
17、eted bythis CPU (e.g. the configuration of a different CPU type or an operating system not compatible with the CPU).WARNING:When you format the MMC all the data that is located on the MMC is deleted!Proceed as follows to format the MMC.1.2.Your CPU requests an overall reset (slow flashing of the STO
18、P LED).Put the switch into the MRES position and hold it there until the STOP LED lights permanently (approx. 9 seconds).You must then release the switch within the next 3 seconds and then put it back into the MRES position. The STOP-LED now flashes during formatting.3.If theMMC cannot be formatted
19、as described above, then the MMC is defective.該文檔是極速PDF編輯器生成,如果想去掉該提示,請并:NOTE:It is only possible to format the MMC if there is data located on the MMC that isinvalid for the CPU. Otherwise the MMC is only initialized through the steps described.More information on the MMC is available in Entry ID:
20、8861901返 回QUESTION 5 :MMC 卡的 S7300 PLC 不能正常調用 SFC54 程序塊?Why does the SFC 54 RD_DPARM not work with the new S7-300 CPU with MMC?ANSWER: ;In the new S7-300 CPUs with micro Memory Card, SFC 54 RD_DPRARM for reading outa data record of a chosen block of the system data configured with STEP 7 has beenrep
21、laced by SFC 102 RD_DPARA.SFC 102 RD_DPARA, in contrast to the old SFC 54 RD_DPARM is an asynchronouslyexecuted system function. This means that the processing is extended over variousSFC calls.Blocks containing SFC 54 RD_DPARM can not be loaded to a new S7-300 CPU with MMC. Therefore, please replac
22、e the call fo the SFC 54 RD_DPARM by the call of the SFC102 RD_DPARA and adjust your programming logic to the asynchronous behaviour of the SFC 102 RD_DPARA an.Below, you will find a comparison of the two system functions:SFC 54 RD_DPARMSFC 102 RD_DPARAObservationsInputs-REQFunction will be executed
23、 only with REQ=1; new for SFC 102IOID-Parameter has been dropped for SFC 102; see LADDRLADDRLADDRSFC 54: any block address, specification of the E resp. A address range over IOID (B#16#54=Peripherie Eingang; B#16#55=peripherial output) SFC 102: any blockaddress; Specification of the E resp. Aaddress
24、 range over bit 15 of LADDR (most siginficant bit) Bit15=0 - peripherial input Bit15=1 - peripherial outputRECNUMRECNUMuse identicallyOutputRET_VALRET_VALuse identically; however, there are additional error numbers for SFC 102 at disposition.該文檔是極速PDF編輯器生成,如果想去掉該提示,請并:Table 1: Comparison SFC 54 and
25、SFC 102返 回QUESTION 6 : 采用 MMC 卡的 S7300 和 C7613,635 系列 CPU 是如何完成數據保持功能的?How does the remanence function of the S7-300 CPUs and C7-613 and C7-635 compactdevices work with Micro Memory Card?ANSWER:The 300theremanence characteristics described below affect the S7-300 compact CPUs, S7- modular CPUs and t
26、he C7-613 and C7-635 compact devices with MMC. We describe remanence characteristics after changes in operating mode in terms of datablocks, times, counters and markersData blocks:CPU STOP/RUN or Power OFF/ON1. Database contents of CPUs 31xC, 312, 314, 315-2DP, C7-613 and C7-635 are always remanent.
27、2. The DBs can be defined as remanent or non-remanent for the CPU 317-2DP.Therefore, a setting in STEP 7(V5.2 +SP1) is required for CPU3172DP:o An explanation for the activation or deactivation ofthe option Non-Retain in the block properties of the DB, can be found in the entry-ID: 17146856 oro a DB
28、 was created with SFC 82 CREA-DBL. While creating a DB with SFC 82 it is determined in the attributes of the DB in Bit 2, whether the DB shall get remanent or not.Note:Only 256K bytes of the main memory (512 Kbyte) can be usedfor remanent data blocks at a CPU 317-2DP! No remanent DB-BUSYBUSY=1; the
29、order has not been finished so far, there are no results at dispositionRECORDRECORDuse identically該文檔是極速PDF編輯器生成,如果想去掉該提示,請并:will be created anymore and the value 80B2 (not sufficientmain memory) will be displayed, if the main small for remanent data blocks.memory is tooMemoryreset (MRES)1.The data
30、will be reset to the values in the (initial value). These are the last currentloading memory values which wereloaded with the PG into the CPU or which were written with the SFC84 into the loading memory.All blocks of the loading memory remain unchanged. The data blocks are initialized in the main me
31、mory.2.CPU Power OFF - pull MMC - Power ON - Power OFF - plug MMC - PowerON1. The data are are the last into the CPUreset to the values in the loading memory. These current values which were loaded from the PGor written into the loading memory with SFC84.2. All blocks of the loading memory remain un
32、changed. The data blocks are initialized in the main memory.Note:If it is required to safeguard current data, those have to be savedon the MMC (loading memory). SFC84 can be used for this purpose. The frequency of the write accesses on the loading memory is critical because a MMC only allows 100,000
33、 write accesses.Markers, times and counter:These operand areas can be defined as remanent or non-remanent in the HWconfiguration under Object properties CPU remanence.CPU STOP/RUN or Power OFF/ONThese operand areas keep their values if they were defined remanent.Otherwise they lose the values and wi
34、ll be initialized with 0.Memory reset (MRES)These operand areas are deleted during the memory reset, regardless whetherthey were defined remanent or non-remanent.CPU Power OFF - Remove MMC - Power ON - Power OFF - Insert MMC - Power ONIf they were defined as remanent, these operand areas retain thei
35、r values. Otherwise they lose their values and initialize with 0. This characteristic applies if the same unchanged MMC is inserted again.QUESTION:What does Non-Retain mean in the Properties - Data Block dialog?ANSWER:In STEP 7 version V5.2 + SP1 and higher you have the option of selecting theproper
36、ty Non-Retain in Properties - Data Block in the General - Part 2 tab. You can define the remanence behavior of data blocks with this option.該文檔是極速PDF編輯器生成,如果想去掉該提示,請并:Fig. 1: Properties - Data BlockThe requirement for this option is that the CPU supports the Retain property of data blocks.A data blo
37、ck with the property Non-Retain is not stored in the remanence memory in a CPU 317 -2DP and is thus reset to the original load values at each power OFF/ON or each STOP-RUN transition of the CPU.A data block with the Non-Retain property occupies remanence memory space.RAM space as usual, but noNote:The CPU 317-2DP has a RAM of 512 KB, but only 256 KBof data can be retained返 回QUESTIO
溫馨提示
- 1. 本站所有資源如無特殊說明,都需要本地電腦安裝OFFICE2007和PDF閱讀器。圖紙軟件為CAD,CAXA,PROE,UG,SolidWorks等.壓縮文件請下載最新的WinRAR軟件解壓。
- 2. 本站的文檔不包含任何第三方提供的附件圖紙等,如果需要附件,請聯系上傳者。文件的所有權益歸上傳用戶所有。
- 3. 本站RAR壓縮包中若帶圖紙,網頁內容里面會有圖紙預覽,若沒有圖紙預覽就沒有圖紙。
- 4. 未經權益所有人同意不得將文件中的內容挪作商業或盈利用途。
- 5. 人人文庫網僅提供信息存儲空間,僅對用戶上傳內容的表現方式做保護處理,對用戶上傳分享的文檔內容本身不做任何修改或編輯,并不能對任何下載內容負責。
- 6. 下載文件中如有侵權或不適當內容,請與我們聯系,我們立即糾正。
- 7. 本站不保證下載資源的準確性、安全性和完整性, 同時也不承擔用戶因使用這些下載資源對自己和他人造成任何形式的傷害或損失。
最新文檔
- 飛行教學課件
- 掃雷教學課件
- 文庫發布:中醫講肝
- 書包小學生課件下載
- 攀鋼集團工程技術有限公司修建分公司-企業報告(業主版)
- 涂色教學課件模板圖片
- 散學典禮班會課件圖片
- 中文韓語教學課件
- 【保山】2025年云南保山市無線電監測中心招聘工作人員1人筆試歷年典型考題及考點剖析附帶答案詳解
- 【南京】2025年江蘇南京審計大學招聘90人筆試歷年典型考題及考點剖析附帶答案詳解
- GB 2758-2012食品安全國家標準發酵酒及其配制酒
- CB/T 3611-1994軸系法蘭連接螺栓鉸孔及裝配質量要求
- 紅星照耀中國1-6章練習匯編(含答案)
- 涉密表格臺賬
- PET分子影像的臨床應用新進展課件
- 桶裝水領用表
- 營運客車等級劃分及評定重點標準
- 精品解析寧夏石嘴山市大武口區20212021學年下學期三年級期末科學試題
- 最新交管b2學法減分題庫及答案
- 藍海華騰變頻器說明書
- 漿砌塊石工程施工程序、施工方法
評論
0/150
提交評論