CO脫除催化劑簡介

1、精選優質文檔-傾情為你奉上一氧化碳脫除劑 CO Removal Catalyst1. 工作原理及流程Operation and Process一氧化碳脫除催化劑可用于脫除石油氣、惰性氣體、氧氣等氣體中少量一氧化碳，還可用于烤爐、壁爐等設備用于催化燃燒未完全燃燒的CO，凈化效果極其優良。在溫度150200，空速（0.31）×104h1條件下，經其凈化后的氣體，一氧化碳含量可降至0.5ppm以下；催化劑吸氧容量可達50ml/g，可催化一氧化碳和氧反應成為二氧化碳，催化劑可以再生使用。HHGS03 catalyst works efficiently to remove CO from p

2、etro gas, inert gas, oxygen and etc, also could be used in various furnace like oven, chimney place, incinerator to treat not burst CO.This catalyst could make CO content less than 0.5ppm under temperature 150200 and space velocity at (0.31.0)×104 h-1; oxygen capacity of this catalyst could be

3、50ml/g, and catalyze reaction CO and O2 to be CO2.Reaction formula: CO+O2 CO22. 工藝特點 Operation Properties一氧化碳脫除催化劑使用前需要配氮氣加熱至180-200活化（烤爐、壁爐等本身是高溫源尾氣的則可用新鮮空氣加熱活化），然后再通入待處理氣體，溫度在200時操作最佳，在1.53.0×103h-1的反應條件下將CO氣體中的CO消除至0.5ppm以下，最高耐熱溫度為750（若可燃性氣體濃度高還需配冷卻系統，防止催化劑燒結），機械強度好，使用壽命可達3年以上。Before using,

4、CO removal catalyst should be heated up to 180200 by nitrogen (fresh air is also available for high temperature exhaust gas in oven and fireplace), in order to active its performance. The optimal operating temperature is 200, and removal CO until 0.5ppm left under operation space velocity (0.31.0)&#

5、215;104 h-1; Max temperature is 750 (cooling system is required if flammable gas is in high concentration).3. 技術指標 Technology Properties序列號No 測試項目Test item 技術參數Technology parameter載體：各種規格堇青石與復合氧化鋁Carrier: cordierite and composite alumina with various specs1 空速Space velocity 3×103h-12 起燃溫度Initia

6、l ignition temperature 100-1503 最佳操作溫度Optimal service temperature 180-2004 CO脫除率CO remova ratioService life 982 years5 壽命Service life 2 years5 CO出口濃度CO outlet content 5ppm6 堆積比重Bulk density 0.68±0.05g/mL7 抗壓強度Crushing strength 14 MPa8 涂層負載Coating component 10.0%9 活性成份負載Activity component 0.1%-0.2% (also depends on your demand)10 脫落率Expulsion ratio 1%11 外觀Appearance Usually is light yellow (would be grey after pre-reduction)12