KYN28維修手冊

1、 KYN28-12鎧裝式金屬封閉開關設備安裝使用與維護手冊江蘇銀佳企業集團有限公司JIANGSU YINJIA ENTERPRISE GROUP CO ., LTD始終安全第一Your safety first-always！在開關設備安裝使用前請先仔細閱讀本說明書 Thats why our instruction manual begins with these recommendations開關設備只能安裝在適合于電氣設備工作的戶內場所。確保由專職電氣人員進行安裝、操作和維護。必須保證現場電氣設備的聯接條件和工作規程的適用和安全性。有關開關設備的一切操作，都要遵守說明書中的相應規定。 危

2、險要特別注意說明書中標有這個危險標志的注意事項。不要超出開關設備在正常工作條件下的技術參數里規定的負載。說明書應放在所有與安裝、操作和維護有關人員能方便地拿到的地方。用戶的專職人員應對所有影響工作安全的事項負責，并正確管理開關設備。若對本說明書尚有疑問，我們將很樂意提供進一步的資訊。- 3 -目錄頁碼1.總則61.1概述61.2標準和規范61.3工作條件61.3.1正常工作條件71.3.2特殊工 特殊工作條件71.3.3注意事項82技術數據82.1電氣參數82.2耐內部故障電弧性能92.3外形尺寸和重量103結構概述123.1基本結構123.2外殼和隔板133.3開關柜內的小室133.4防止誤

3、操作的聯鎖/保護164運輸和保管204.1交付條件204.2包裝204.3運輸214.4交貨和中間保管225開關柜的現場安裝245.1安裝現場的一般要求245.2配電室平面布置基本方案245.3基礎255.3.1以配電室地板作為基礎255.3.2在混凝土地坪上的基礎框架265.4開關柜的安裝與拼接275.5母線的安裝聯接295.6電力電纜和控制電纜的聯接305.7接地銅排的聯接315.8安裝工作的收尾32目錄頁碼6 開關柜的運行376.1起動376.1.1準備工作376.1.2起動396.2開關柜的操作406.2.1斷路器手車406.2.2斷路器426.2.3接地開關436.2.4電纜室門44

4、6.2.5電氣/機械的指示/監控447維護457.1概述457.2檢查和保養467.3修理497.3.1一般性修理497.3.2更換元件497.4備件49 版權所有，禁止將本說明書的全部或部分，以任何形式提供給第三者。公司保留對提供的數據和圖解的更改權力，需更改時，不另行通知。- 49 -1 總則 1.1 概述 KYN28-12鎧裝式金屬封閉開關設備（以下簡稱KYN28-12開關柜）適用于三相交流50Hz、7.212kV單母線及單母線分段電力系統，具有“五防”功能。開關柜的可移開部分可配置真空斷路器和真空接觸器等元器件。1.2 標準和規范 KYN28-12開關柜滿足IEC298，GB3906，

5、DL404等標準。開關柜外殼的防護等級為IP4X，當斷路器室門打開、手車移開時，防護等級為IP2X。在系統的安裝和運行期間，要遵守所有相關的IEC規范及國家或地方相關的安全導則，還應考慮江蘇銀佳企業集團有限公司提供的有關資料。1.3工作條件1.3.1 正常工作條件 KYN28-12開關柜正常工作條件如下：室內環境溫度：最高溫度 +40°C日平均值不大于 +35°C最低溫度 -15°C室內環境濕度： 日平均相對濕度 95%及以下 月平均相對濕度 90%及以下Monthly average relative humidity less than 90%安裝場所的海拔高

6、度 1000m及以下Height above sea level at site less than 1000m地震烈度: 不超過8度Earthquake intensity: less than 8 degree沒有火災、爆炸危險，沒有嚴重污穢及化學腐蝕的場所。This product should not be used under conditions of fire, explosion，earthquake and chemical corrosion environments.1.3.2特殊工作條件Special service conditions對特殊工作條件，必須向制造廠咨詢

7、。制造廠與用戶應就特殊工作條件取得一致意見。The manufacture must be consulted in advance about each special service condition. Special service conditions are to be agreed on by the manufacturer and user. l 已考慮安裝場所的海拔高于1000m時，空氣介質強度的降低對絕緣水平的影響。Allow for the reduction in the dielectric strength of the air when site altitud

8、e is over 1000ml 若環境溫度超出極限值，在母線和分支母線的設計上加以補償或限制載流量。在柜內安裝通風裝置將有利于開關柜的散熱。If the ambient temperature is over top of the high-point, must consider equalizing or limiting current capacity for the design of main bus bar and branching bus bar. Installation the aerator is favor of rejection of heat.1.3.3 注意

9、事項：Matters need attention：若開關柜運行地區的濕度較高，溫度波動速度較快且幅度較大，開關柜在這種氣候環境下運行，就有凝露的危險，因此開關柜在備用和運行狀態下，用戶應保證加熱器全天侯投入！但在大電流運行中，可以不投入。If the humidity is higher on site, temperature fluctuations speed is rapidder and range is bigger, condensation phenomena will be appear for the switchgears running in this clime c

10、ondition, so user should ensure that the heater running full time on spare and running condition! But running in high-current, the heater can stop. 2技術數據 Technical data2.1 開關柜電氣參數 Switchgear technical data額定電壓kV12額定絕緣水平1min工頻耐壓（有效值）kV42雷電沖擊耐壓（峰值）kV75額定頻率Hz50主母線額定電流A630,1250,1600，2000，2500，3150，4000分

11、支母線額定電流A630，1250，1600，2000，2500，3150，4000*4秒熱穩定電流（有效值）kA16，20，25，31.5，40*額定動穩定電流（峰值）*kA40，50，63，80，100Rated voltage kV12Rated power-frequency withstand voltage(1min)kV42Rated lightening impulse withstand voltagekV75Rated frequencyHz50Rated main bus bar current A1600，1200，2500，3150，4000Rated branchin

12、g bus bar currentA630，1250，1600，2000，2500，3150，4000*4s Short-time withstand current（rms.）kA16，20，25，31.5，40Peak withstand current（peak.）kA40，50，63，80，100，125*需裝備通風裝置 with forced ventilation.*40 kA為3秒 3 second for 40kA*儀用互感器的短路容量應單獨考慮 The short-circuit capability of transformer for measure should be

13、considered by oneself.2.2 耐內部故障電弧性能 Performance bearing inside fault arcKYN28-12開關柜在設計上已考慮到開關柜內部故障電弧的問題，根據GB3906和IEC298進行了嚴格的試驗，能有效地保證設備及操作人員的安全。KYN28-12 has been considered with the problem of inside fault arc in switchgear on design. It is tested strictly according to GB3906 and IEC298, thus ensur

14、e effectively the safety of equipments and operation personnel.2.3外形尺寸和重量 Outline dimensions and weight 外形尺寸 Outline dimensions高度a （mm） 2200寬度b （mm）分支母線額定電流為1250A及以下，短路開斷電流為31.5kA及以下 800/650*分支母線額定電流為1600A及以下，短路開斷電流為40kA 800分支母線額定電流為1600A及以上 1000深度c （mm） 1350/1500Height a 2200（mm） Width b Rated bran

15、ching bus bar current up to 1250A，Rated short-circuit breaking current(rms.) up to 31.5KA 800/650*（mm）Rated branching bus bar current up to 1600A，Rated short-circuit breaking current(rms.) up to 40KA 800 (mm)Rated branching bus bar current over 1600A， 1000(mm)Depth c 1350/1500 （mm） 重量8001200kg，詳細資料見

16、表1。*配VD4斷路器可用。Weight 8001200kg，for table 1showing.*Suitable for VD4 being equipped.表1 安裝要求的尺寸及柜體重量柜內設備型式移開式移開式移開式柜深 c柜寬 b距墻距離mmmmmm150065080015008001000150010001200走廊寬度*mm100011001200安裝通道(室內通道要求)寬度長度（深）門框要求寬度高度mmmmmmmm10001500800220010001500100022001200150012002200重量（近似值）地坪承重kgkg/m280010008501000120

17、01000List 1 Dimension and weight for switchgear installationMode of devicein switchgearRemovingtypeRemovingtypeRemovingtypedepth cWidth bDistance to wallmmmmmm1500650501500800501500100050The width of Passage *mm100011001200Assemble walkwayDemand of passage indoorWidthLength（Depth）Demands of door fra

18、meWidthHeight*mmmmmmmm10001500800200010001500100022001200150012002200Mass（approximation）Weight terrace bearedkgkg/m28001000850100012001000*取決于最大柜寬Depend on the most width of the switchgear3 開關柜結構概述Structure general of switchgear3.1基本結構（圖3/1）Basic structure（Figure3/1）開關柜由固定的柜體和真空斷路器手車組成，這是它的基本結構。開關柜及

19、安裝的電氣元件見圖3/1。進線柜或出線柜是基本柜方案，并有派生方案，如母線分段柜或計量柜等。此外，尚有配置固定式負荷開關、真空接觸器手車、隔離手車等方案。開關柜靠墻或面對面安裝。結構細節和柜內安裝設備，可見訂貨文件。The basic structure of switchgear panel comprises the panel itself a removing part. The panel and main components can see in figure 3/1.Incoming-line panel or outgoing-line panel are diagram o

20、f basic switchgear panel，there are other derivative diagram，for example ,contact panel or metering panel .in addition，There are so many diagram of the switchgear panel with stationary type load switch、（SF6）VCB truck、VC truck、Disconnect truck. The panel has two maintenance modes. That is single-face

21、maintenance and double-face maintenance. The detail of structure and main components, can reference order document.3.2外殼和隔板 Enclosure and clapboard開關柜的外殼和隔板由優質鋼板制成，具有很強的抗氧化、耐腐蝕功能，且剛度和機械強度比普通低碳鋼板高。三個高壓室的頂部都裝有壓力釋放板。出現內部故障時，高壓室內氣壓升高，由于柜門已可靠密封，高壓氣體將沖開壓力釋放板釋放出來。相鄰的開關柜由各自的側板隔開，拼柜后仍有空氣緩沖層，可以防止開關柜被故障電弧貫穿熔化。

22、低壓室D裝配成獨立隔室，與高壓區域分隔開。隔板將斷路器室B和電纜室C隔開，即使斷路器手車移開（此時活門會自動關閉），也能防止操作者觸及母線室A和電纜室C內的帶電部分。卸下緊固螺栓就可移開水平隔板，便于電纜密封終端的安裝。The enclosure and clapboard of the switchgears is made up from high quality steel, have very strong function to resistant oxidation and corrosion, and its rigidity and mechanical robustness

23、is higher than common low-carbon steel board. Have been installed release of pressure plate on the top of three high-pressure chambers. When appear internal fault electric arc, air pressure heightens in high-pressure chamber, because that the doors of switchgear is already airtight coating, the pres

24、sure gas will clash out the release of pressure plat. Adjacent switchgears are isolated by its self side board, after putting the switchgears together, air buffer layer exist yet, it may prevent the switchgears from pronging and melted by electric arc. Low-voltage vault D is separate room with high-

25、pressure area. Clapboard space isolate the VCB vault B with cable vault C, even if VCB. truck is moved(here the valve is closed self-motion),can prevent the operator from touching the electrification parts of bus bar vault A and cable vault C. releasing the tighten bolt, the level clapboard is remov

26、ed, convenient for installation of cable seal terminal.3.3開關柜內的小室 Compartments in switchgear斷路器室（見附圖3/1，3/3，3/5，3/6）VCB vault (figure 3/1，3/3，3/5，3/6 showing)斷路器手車裝在有導軌的斷路器室B內，可在運行、試驗/隔離兩個不同位置之間移動。當手車從運行位置向試驗/隔離位置移動時，活門會自動蓋住靜觸頭，反向運行則打開。手車能在開關柜門關閉的情況下操作，通過門上的觀察窗可以看到手車的位置、手車上的ON（斷路器合閘）/OFF（斷路器分閘）按鈕、合分

27、閘狀態指示器和儲能/釋放狀況指示器。VCB truck is installed in VCB vault B with track, may move in the middle of the position to service and test/disconnected. While the truck move from service position to test/disconnected position, the valve can cover un-move contact in self-motion, open when moving reverse. The tru

28、ck can be operated when the truck vault door is closed, while you can watch the position of the truck, on (VCB tripping)/off(VCB closing) push knob in the truck, close and open indicator and charging/releasing indicator by inspection window. 斷路器手車 VCB truck手車可采用手動進行移動?？蚣苡珊辖痄摪迤囱b而成，上面裝斷路器和其他設備。具有彈簧觸頭系

29、統的觸臂裝在斷路器的極柱上，當手車插入到運行位置時起電氣聯接作用。手車于開關柜之間的信號、保護和控制線，用一個控制線插頭聯接。手車剛插入開關柜就固定在試驗/隔離位置，同時也可靠地聯接到開關柜的接地系統。手車的所在位置，能通過觀察窗或裝在低壓室面板上的手車電氣位置指示器看到。除真空斷路器外，手車可配真空接觸器、隔離裝置和計量設備等。The truck can be moved by manual. The structure of the truck is made of the steel, the VCB and other equipments are installed on top o

30、f it. The arm of spring bush is installed on the pillar of the VCB，When the truck is pushed on the service position, it has the effect of electrical interlocking. The signal 、protection、control line between the truck and the switchgear is connection with the pin of control line. The truck is fixed o

31、n the test position as soon as it is pushed into the switchgear, and be connection to the earth system of the switchgear. The position of truck will be seen by the lamp that is installed on the looking window or the panel of low-voltage.Beside the VCB, the Truck can be equipped the vacuum contactor

32、、isolated device and the measuring equipment.母線室 Bus bar compartment母線從一個開關柜引至另一個開關柜，通過分支母線和套管固定。矩形的分支母線直接用螺栓聯接到主母線上，不需任何聯接夾。所有母線和分支母線都用熱縮套管覆蓋。套管板和套管將柜與柜之間的母線隔離起來，并有支撐作用。對電動應力大的開關柜，一般需要這種支持。The bus bar from one switchgear to the other switchgear is fixed with the bushing and the ramus bus .The ramus

33、 bus is connection to the main bus with the bolt, it neednt any clip. All bus and the ramus bus are covered with pyrocondensation bushing. The panel of bushing and bushing are isolated between the switchgear and the switchgear. And it has the effect on supporting.電纜室（圖3/1）Cable compartment（drawing 3

34、/1）電流互感器和接地開關裝在電纜室后部。電纜室也可安裝避雷器。當電纜室門打開后，有足夠的空間供施工人員進入柜內安裝電纜（最多可并接6根）。蓋在電纜入口處的底板可采用非導磁的不銹鋼板，是開縫的，可拆卸的，便于現場施工。底板中穿越一、二次電纜的變徑密封圈開孔應與所裝電纜相適應，以防小動物進入。對于濕度較大的電纜溝，建議用防火泥、環氧樹脂將開關柜進行密封。CT and earth switch are installed on the back of the Cable Compartment. The Surge arrester is also installed on the Cable C

35、ompartment. When the truck and the horizontal panel are moved .There is enough room so that the worker install the cables (the most is 6).The bottom of panel that lie on the incoming of cable in made of the stainless steel panel，It is uncork, disassembly so that working on the local. The airplane of

36、 panel where is together secondary cable make sure as same as the installed cable prevent the small animal being into it.For the cable trench in humidity，It is suggested that the switchgear is airproofed with fireproofing mud and epoxide resin.低壓室（圖3/1、3/2） Low-voltage compartment (figure 3/1、3/2)開關

37、柜的二次元件裝在低壓室內及門上?？刂凭€線槽空間寬裕，并有蓋板，左側線槽用來引入和引出柜間連線，右側線槽用來敷設開關柜內部連線。低壓室側板上有控制線穿越孔，以便控制電源的聯接。Low-voltage components of switchgear are installed in low-voltage compartment and on door. Control wiring trunking has ample space and cover board. Nearside wiring trunking is used to introduce and educe the wirin

38、g between switchgears, starboard wiring trunking is used to lay intramural wiring in switchgear. Traversing hole for control wiring on side board in low-voltage compartment is used to connect with control power supply.3.4防止誤操作的聯鎖/保護 Interlocks/protections for preventing mishandling具備一系列的聯鎖裝置，從根本上防止出

39、現危險局面和可能引起嚴重后果的誤操作，因此有效地保護了操作人員和開關柜。聯鎖裝置地功能如下：A series of interlocks are provided to prevent mishandling, thus protecting both personnel and switchgear itself. The function of interlocks is following: Ø 斷路器和接地開關在分閘位置時，手車能從試驗/隔離位置移動到運行位置。在這種分 閘狀態下，反向移動也行（機械聯鎖）。 VCB and earth switch in the OPEN p

40、osition, you can move the truck from the test/disconnected position to service position. On this state, it is be able to move reversely yet(electric interlock). Ø 手車已完全處于試驗或運行位置時，斷路器才能合閘（機械和電氣聯鎖）。Only the truck quite in the test or service position, VCB can be closed (machine and electric inter

41、lock).Ø 手車在試驗或運行位置而沒有控制電壓時，斷路器不能合閘，僅能手動分閘（電氣聯鎖）。The truck is in the test or service position, but no given control voltage, VCB is not closed, only manual open (electric interlock).Ø 手車在運行位置時，控制線插頭被鎖定，不能拔出。The truck in the service position, control wiring plug have been locked, dont be pul

42、l out.Ø 手車在試驗/隔離位置或移開時，接地開關才能合閘（機械聯鎖）。Only the truck have been in the test/disconnected position or moved out, the earth switch is permitted to be closed (machine interlock).Ø 接地開關關合時，手車不能從試驗/隔離位置移向運行位置（機械聯鎖）。When earth switch has been closed, the truck dont move from the test/disconnected

43、 position to service position (machine interlock).Ø 可在手車和/或接地開關操動機構上安裝附加聯鎖裝置，如閉鎖電磁鐵，用戶在訂貨時應提出要求。 Some additive interlocks can be assembled on the truck and/or earth switch operating mechanism, as case electromagnet, user should provide the required information when ordering. 隔室：CompartmentA母線室

44、Bus bar compartment C電纜室 Cable compartmentB斷路器室 Truck compartmentD低壓 Low-voltage compartment主要部件：Master parts1母線 Bus bar 2絕緣子 Insulator3靜觸頭 Fixed contact4觸頭盒 Bush 5電流互感器 Current transformer6接地開關 Earth switch7電纜終端 Cable terminal 8避雷器 Arrester 9零序電流互感器 Zerosequence current 10斷路器手車VCB truck10.1滑動把手 Sli

45、p handle10.2鎖鍵（聯到滑動把手）Lock key（link to sliding handle）11控制和保護單元 Control and protection unit12穿墻套管 Wall bushing圖3/1：KYN28-12進線或出線柜基本結構剖面圖Figure3/1：Basic structural sectional view of incoming line or outgoing line主要附件：Master accessories13絲桿機構操作孔Operation hole of screw machine14電纜夾 Cable grip15.1電纜密封圈

46、Cable lock-ring 15.2連接板 Connection board16接地排 Earth bus 17二次插頭 Control wiring plug17.1聯鎖桿 Interlock lever 18壓力釋放板 Pressure-relief plate19起吊耳 Flying rings20運輸小車 Transport cart20.1鎖桿 Lock bar 20.2調節輪 Regulating wheel20.3導向桿 Guide bar 圖3/2低壓室內部視圖，端子排座可向上旋轉以便輔助開關的安裝，控制線的布線和接線Figure 3/2 Intramural view i

47、n low-pressure chamber. In order to install auxiliary switch, controlwiring and connection, the terminal foundation can be circumrotated upwards.圖3/3 斷路器室門打開，手車在試驗位置Figure 3/3 Door of the VCB truck compartment is opened, the truck in the test position圖3/4 斷路器手車在向運行位置插入Figure 3/4 Insert the VCB truck

48、 to service position21活門Valve10.3梅花觸頭Contactor4觸頭盒Bush10.4觸臂Contact arm10斷路器手車VCB truck圖3/5 斷路器手車Figure 3/5 VCB truck 圖3/6 手車移去后，活門打開時斷路器室內部視圖Figure 3/6 Intramural view of VCB compartment when the valve is open, the truck has took off17控制線插座Control wiring plug3靜觸頭Fixed contact4觸頭盒Bush21活門Valve4運輸和保管

49、 Dispatch and storage4.1交付條件 Condition on delivery 除了根據訂單檢查外，裝配好的開關柜還應遵照相應的IEC 298及GB3906有關規定進行出廠試驗，校核結構和功能的正確性。母線、緊固件和附件是單獨包裝的。The assembled switchgears are still tested for leaving factory in accordance with IEC 298 or GB3906 except that it is checked in accordance with order form, thus verifying

50、their correct structure and function. Bus bar, fastening piece and accessory are packed by oneself.4.2包裝 Packaging 開關柜的包裝按具體情況的要求作相應的調整，如航海包裝或不包裝。特別是海上運輸，即使是裝在集裝箱內，也應用塑料薄膜袋將開關柜封裝起來，放入合適的干燥劑以防受潮。The packaging of switchgear may be adjusted according to request for specific conditions, such as navigati

51、on packaging or no packaging. Especially marine transport, the switchgear must be sealed in film even though it is packed in container, put appropriate drier in packaging for guard against damp. 4.3運輸 Transport通常由單臺開關柜組成運輸單元，例外情況下，可由開關柜小組或背靠背安裝的開關柜組成運輸單元。每臺開關柜都裝有4個吊耳。（見圖5/1，5/2）Generally transport unit is formed by single switchgear. Transport unit can be formed by switchgear group or switchgears fixed back-to-back for exceptional case. Every switchgear has four lifting lugs. (see figure 5/1,5/2)開關柜應直立運輸，必須采取保護人員和器材的安全措施，用下列工具之一，才能進行裝載工作：Switchgears should be transported er