風冷冷風型空調機安裝使用說明書

1、目 錄CATALOGUE一、機組外觀和機組結構1Unit outlook and structure二、系統流程圖3system flow chart三、機組安裝4Installation四、調試18Test五、使用20Operation六、維護和保養25Maintenance七、運行圍26Run scope八、簡易故障處理27Trouble disposal一機組外觀和機組結構 Unit outlook and structure工機組外觀1回風口 air inlet2出風口 air outlet3接水管排水孔drain pan weep hole4室內外機連接口indoor & o

2、utdoor unit connection5底盤排水孔classic weep hole6電源線孔 power wire hole7壓力表 pressure gauge8控制面板control panel9室外機 outdoor unit2.機組結構 Unit structure1 .壓縮機 Compressor2 .電加熱 Electric heater3 .蒸發器 Evaporator4 .過濾網Filter9.球閥 Ball valve5 .風機Fan6 .電控箱 Electric controller7 .電機 MotorS.室外機 outdoor unit注：1.單冷機使用毛細管節

3、流(50HP以下)；For single cooling unit, capillary should be used to throttle.(below 50HP)2 .熱泵機使用膨脹閥節流,空內機室外機各安裝一個；For heat-pump unit, expansion valve is used to throttle, installing each one both in indoor and outdoor units.3 .氣液分離器安裝于室內機；Gas and Irquide separation is installed in indoor unit.以上三點示意圖上均未

4、表示.The three points above have not been shown in the sketch map.二,系統流程圖system flow chart1、風冷冷風型/電加熱型空調機工作原理Working principle of the air-cooled cooling or electric heating air conditioner蒸發器capillary毛.； 細算 管|vaporatorjointing pipe接管Tx卜ball valve球閥condenseraxial fan軸流風機A冷凝器dryer-filter panel干燥過漁器joint

5、接頭jointing pipe接管ball valve球閥-Joutside室外側inside室內側2、熱泵型空調機工作原理Working principle of the heat-pump air conditionerball valve球閥joint接頭gas and liquid separation compressor氣液分離器han室外換熱器electric heaterUo ,電V 加axial fan ;熱軸流風棚,器fpur way valveA ball valve-rT 球閥_mjoint接頭outside室外側一爾縮機一_一 一 centrifugual fan e

6、xpansion vdfve 渴心風機 filter膨張莉 過 灌 器 ' -siglc dirction valve制熱循環 heat cycle制冷循環refrigeration cycleinside室內側inside l|eat exchanger室I內I換 熱| 器1.低壓繼電器 low pressure relay2.高樂繼電器high pressure relay三,機組安裝1 .安裝空間:Installation space確保機組安裝位置周?chē)凶銐虻目臻g以備操作、維修之用，同時也要保證氣流循環 暢通，不受阻礙并且沒有短路。安裝空間尺寸參見下圖。In order to

7、ensure operation and maintenance convenient , enough space around the units must be ensured while installing . Air must flow freely without resistance and short circuit . Installation space size can be consulted as follows .型號modelABc3HP、5HPx 8HP、10HP50050012.5HP、15HP50080020HP. 24HP500800100025HP、3

8、0HP、40HP、50HP5001000100060HP. 70HP、 80HP、 100HP、11 OHP100015001500、注：假設A為無連接管側.B為連接管例。Note: assume A not to be side of connecting pipe, B to be side of connecting pipe.2 .安裝定位 Installing location應考慮電氣接線、室外機連接、排水管布置以及風管連接的方便。確保地面平整、水 平，機組安裝后傾斜度不應超過下圖要求。Must count for the convenience of electric wirin

9、g, connection of indoor and outdoor unit, arrangement of drain pipe and air duct connection while installation. Ensure ground to be flat and level, after installing/ unit gradient can not exceed the limit showed in following chart.地基應有足夠的強度。機組重量和地腳螺釘固定位置參見以下各圖。Foundation should be intended enough. U

10、nit weight and the foot screw fixed position is showed as following charts .其它注意事項:Other attentions(1)室外機組安裝位置要選擇適當，必須安裝在無日光照射、遠離熱源的地方。Indoor and outdoor unit must be installed in the place which has no sunlight illuminated and far from heat resource.(2)室外機組安裝應考慮對建筑物外觀的影響。The influence on the buildi

11、ng appearance must be considered when install the outdoor unit.(3)安裝安置應盡量選在管路短、彎曲少、高差小的地方。Installation should be situated in places where the pipe is short, bends are few and the height difference is little.(4)室外機組的位置不在地面或樓頂平面而需懸掛在墻壁上時，應制作牢固可靠的支架。While outside unit is not installed on the ground or

12、the top plane, but hung on the wall, it must use the firm support.(5)室外機組出風口不應對準強風吹的方向，上面不應有障礙物。若頂部空間不夠時， 需安裝彎曲型導風管將風導向遠處，以避免氣流短路而影響機組性能。The outside unit's air outlet couldn't be in the direction of strong breeze , and there won' t be obstacles above it . If the above space is not enough

13、, please install bending type wind duct to guide the wind to distance , avoiding that unit performance will be influenced by air flow short .(6)側出風型室機安裝在空調房時，除考慮安裝方便外，還要保證氣流合理，送風均 勻。While side air outlet model indoor unit* s installation in the air conditioner room, except considering convenient ins

14、tallation, it should ensure air flow reasonably and air supply equably.(7)任(可惜蝦，室推由叼節裝裝在室外。In any case, the inside unit should not be installed outside.3 .安裝 Installation示例圖 demonstrationa.搬運.吊裝 Handling, hoisting機組可用鏟車或吊車運輸，吊裝時應如下圖進行操作。Unit can be transported by forklift or hoistr please operate as

15、 the followingchart while hoist.必須大于60'包裝箱底架 paking box chasismust large than 60°注意事項 Attentions(1)吊裝前應檢查機體吊環是否旋緊，纜繩是否安裝牢固。Before hoisting, should ensure the organism rings tightened, the hawsers fastened. 搬運或吊裝過程中，應保持機體平衡，切勿突然升高、降低5捌烈晃動。During handling or hoisting, keep organism balance, d

16、on' t rise, drop suddenly or sway violently.b.管路布置 Pipes arrangement連接管路的布置須根據現場情況參照以下原則進行：Connection pipe arrangement must according to the site1 s condition and refer to the following principles:(1)盡可能縮短連接管長度，最好在5m以Try to shorten the length of connection pipe, best within 5m.每4、6米設1個存油彎.室外機Out

17、door unitb.室外機置于室內機之上Outdoor unit higher than indoor unit。(2)盡可能減小室外機高度差。Try to shorten the altitude difference between indoor and outdoor units.(3)盡可能減少連接管路的彎頭數。Try to reduce the joint1 s amount used for connection if possible.(4)連接管長超過20米時，需檢查系統的潤滑油是否足夠，必'要時，需適當增加。When pipe longer than 20m, in

18、spect lube whether it is enough, add it when necessary.當室外機高度不同時，參照下圖進行管路布置。If indoor and outdoor unit s altitudes are difference, arrange the pipeline according to following graph .液管(即細管)liquid pipe (thinner pipe )氣管(即粗管)gas pipe (thicker pipe )c.室外機置于室內機之下(壓縮機在室內機)Outdoor unit lower than indoor u

19、nit, compressor is in inside unit.室外機連接管的高差、管長及彎頭數按下表限制：Altitude difference, pipe length and elbow' s amount of connection pipe ofindoor and outdoor unit defined by following table :c.連接步驟 Connection steps(1)工具準備 Preparing tools一切工具、備件、材料必須準備齊全，如沖擊鉆、真空泵、氮?dú)馄?、配管工具、?冷劑壓力表等。All tools, reserve parts

20、 and materials must be prepared all in readiness, for example : Percussion drill vacuum pumpr nitrogen cylinder, pipe-fit tools, refrigerant gauge and so on .室機安裝 Indoor unit installation參照前述要求安裝固定室機。Install and fix indoor unit according to above demands .(3)室外機安裝 Outdoor unit installation參照前述要求安裝固定

21、室外機。Install and fix outdoor unit according to above demands .室外機型號 Outdoor unit modelSW-3NSW-(4X2)NSW-3RNSW-5NSW-(5X2)NSW-5RNSW-8NSW-(6X2)NSW-8RNSW-10NSW-10RNSW-13NSW-13RNSW-15NSW-15RNSW-20NSW-20RNSW-25NSW-25RNSW-30NSW-30RNSW-60NSW-70NSW-80N最大管長Max.pipe length20203030405050505050最大高度差Max.Altitude do

22、ffs.10101515202525252525最多彎頭數(90°。Max.elbow.meter6688101212121212(4)打墻孔 Drill holes in wall在墻底部打圓孔或長方形孔，以穿過連接管、排水管、電線等。Drilling round or square holes in the bottom wall to let connecting pipe, water drain pipe and wires cross .(5)管路連接 Connecting pipes申菱牌風冷系列空調機管路連接方式有兩種：小于或等于LF/LFD29N以及 LF/LFD5

23、8N. LF/LFD85N機組采用喇叭口連接，其它類型機組采用焊接方式連接。 連接時須注意以下幾點：There are two methods to connect pipes of SHENLING'1 air-cooled series air conditioner: Flared-tube connection is for units smaller than LF/LFD29N and LF/LFD58N/ LF/LFD85N. And welding connection is for the other units. The following points must

24、be paid attention to while connecting;喇叭口連接方式Way of flared-tube connection(a)盤管展開時采用反繞的方法緩慢進行,避免折扁銅管。Unfold coiled pipe slowly by way of twisting in reverse, so as not to bend the copper tube flatted.(b)管道的彎曲加工用彎管器進行，彎曲半徑較大時也可用手緩慢地彎曲。彎曲半徑過小，容易造成管子損壞，彎曲半徑限度要求不小于銅管外徑的6倍。Use tube bender to bend machine

25、ry pipe or bend by hand when the radius of curvature is larger . If the radius of curvature is too little, pipes may be miner than 6 times of the pipes external diameter.(c)松開角閥連接處螺母，卸下連接管堵頭，在喇叭處涂上冷凍油，快速地將兩者 連接起來(要求5分鐘)，喇叭口位置對好之后，再用板手緊固螺母。Loosen nut and remove the plug from eagle valve, then smear t

26、he flared with refrigerant oil and connect the two parts together quickly (in 5 minutes), when the flare' s seat well, then tighten the nut using spanner.(d)當所需要管長超過5m時，需按要求加長銅管并補充制冷劑If connecting pipe is longer than 5m, increase the length of the copper pipe and add refrigerant.焊接方式： Way of wel

27、ding connection(a)采用硬釬焊連接所有接頭。Connect all joints by braze welding.(b)銅管切割后須清除毛刺及管異物。Get rid of the bur and foreign matter in pipe after cutting the copper tube.(c)焊接時管必須充氮。Fill tube with nitrogen when welding.(6)充氮試漏Charge with nitrogen to have leakage test銅管連接之后，從接頭處制冷劑充注口(喇叭口連接式在角閥上，焊接式須打開所 有室側球閥，

28、再?gòu)氖覚C(jī)制冷劑充注口充氮)充入氮?dú)庵?.5Mpa ,用肥皂液檢查連 接管各接頭處是否有漏，若有漏，接頭必須重新處理。注意：切勿用氧氣或乙快氣試漏！After connecting copper pipe, charge with nitrogen to the pressure of 1.5MP through charging valve at the joint (the charge valve of flared connecting type is at the eagle valve, but as to welding connecting type, all indoor si

29、de ball valve must be opened, then charge nitrogen through the charge valve of indoor unit). And using soapsuds to check every joint of the connection pipe to see if there is any leakage or not, if it is, the joint must be dealt with again .CAUTIONS: Be sure not to do leakage test with oxygen or ace

30、tylene.(7)空氣排除 Air discharge充氮試漏之后，必須排除管道空氣。因系統空間較大，建議采用真空泵抽除管道空 氣，不要采用放制冷劑方法來排除管道空氣。否則由于排除不凝性氣體不徹底會造 成系統高壓升高和制冷性能下降。Air in pipes must be removed after leakage test. As the system space is a little large, vacuum pump is suggested to draw air from the pipe, not to get rid of the air by charging pipe

31、with refrigerant or because incondensable gas can not be exhausted, the high pressure of system will rise and refrigerant rating performance descend.(8)真空檢漏 Vacuum leakage test抽真空至管絕對壓力1300Pa,保持5分鐘壓力無變化，否則接頭處有漏須重新處 理。抽真空時，喇叭口連接式只需抽除管道空氣，焊接式必須開啟室側所有球閥后 (因室機充有少量氮?dú)?，所以必須連同室機一起抽，但室外機球閥不能開)，再在空調機 制冷系統的高低壓

32、兩端制冷劑充注口分別抽除空氣，不能只抽一端。Achieve the vacuum in pipe (absolute pressure 1300Pa) and keep it for 5 minutes without pressure changing/ and if it changed, there must be a leakage in joints, so the joints must be dealt with again. Only the air in pipe need to be vacuumed for flared connecting type unit. But

33、 for welding connecting type unit all indoor side ball valves must be opened (because indoor unit has been charged with a little nitrogen, pipe must be vacuumed with indoor unit together, but ball valves of outdoor side can not be opened), the draw air separately from the charging valve of the refri

34、geration system in air conditioner, when vacuuming , pay attention not to vacuumone side only.(9)放出制冷劑 Let refrigerant out空調機出廠時制冷劑貯存在室外機。放出制冷劑時應先打開制冷劑液路兩個角閥 (或球閥)，再打開另兩個角閥(或球閥)。開啟角閥時須注意，必須擰開至上死點并略 擰緊，再蓋上防漏蓋帽。球閥只需將閥桿轉90°,(閥桿上有箭頭指示流動方向)再蓋 上防漏蓋帽。所有閥都打開之后，須將原"全關"掛牌換為"全開"掛牌。Refr

35、igerant is stored in outdoor unit when air conditioner leaving factory . Open eagle valve ( or ball valve)f which is thinner pipe' s valve, in refrigerant liquid pipe of every system first when letting refrigerant out, then open other two eagle or ball valve . While opening eagle valve, the valv

36、e rod must be opened to the top dead center and tighten a little, then leak proof cup must be fitted. For ball valve, turn the rod to the eagle of 90° (there is arrow indicating turning direction) and fit the leak proof cap . After all valve opened, change the hanging plate "Close all"

37、; to "Open all”(10)復查接口泄漏 Check again the joints leakage閥門開啟之后，用鹵素檢漏儀或肥皂液在接口處復查有無泄漏。After valves opened, use halide leak detector or soapsuds to check thejoints .(11)電線連接 Connecting electrical wires用多芯電纜線連接室外機接線端子。Use multiple core cable with every conductor/ s section being to connect indoor a

38、nd outdoor terminals .注意：每臺室外機必須按序號和相對應的制冷系統的電路部分進行連接，切勿接錯， 否則空調機不能正常運行。Note : Each outdoor unit must connect with electrical branching of corresponding refrigeration system according to the number, if in disorder, the air conditioner cannot operate normally .(12)包扎 Wrapping up連接銅管包好保溫層之后(僅對焊接方式而言，喇

39、叭口方式銅管上已套好保溫管), 將銅管、電線等用塑膠帶妥善包扎并固定好。After connection copper pipe binding up the thermal insulation (only for welding way connection for flared tube connection, the pipe has been cased with insulation layer) . Then bind up pipesf wires, etc. with plastic tape and tighten them .4 .制冷劑補充 Supplementing

40、refrigerant當連接管路超過5m時，必須補充制冷劑（R22）,請用戶安裝時參照下表進行 補充。停機時補充制冷劑可從角閥冷劑充注口充入，開機時補充制冷必須從壓縮機 吸氣口(即低壓端，壓縮機較粗的接管)冷劑充注口吸入，此時冷劑罐不宜倒置，以 保證制冷劑以氣體方式吸入壓縮機，避免壓縮機發生液擊而受到損壞。When connecting pipe is in excess of 5m, refrigerant (R22) must be supplemented while user installing . Please refer to following table. When unit

41、 is not working, refrigerant can be charged from charge plug at angle valve, if the air conditioner is operating, refrigerant must be charged from the plug of compressor' s drawing side (lower pressure side, thicker connecting pipe of compressor), at this moment the refrigerant can be drawn into

42、 compressor as gas, for preventing the compressor from damaging because of liquid shocking .室外連接管長每增加lm時制冷劑補充量表Table of the quantity of supplementary refrigerant when connecting pipe in different length室外機 型號SW-3NSW-(4X2)NSW-3RNSW-5NSW-(5X2)NSW-5RNSW-8NSW-(6X2)NSW-8RNSW-10NSW-10RNSW-13NSW-13RNSW-15N

43、SW-15RNSW-20NSW-20RNSW-25NSW-25RNSW-30NSW-30RNSW-60NSW-70NSW-80N每米管 長制冷 劑量kg0.110.110.180.180.260.260.370.370.511.021.31制冷量修正系數 Correcting coefficient of cooling capacity當室外機連接管長過長或兩機高低差過大時會影響制冷能力，制冷量的修正系數參見下 表。Cooling capacity will be influenced when connecting pipe of indoor and outdoorunit is too

44、 long or the altitude difference of the two units is too large . Thecorrecting coefficient is listed in following table .制冷量修正系數 correcting coefficient of cooling capacity等效總長 equivalent total length5m10m15m20m25m30m35m40m45 m50m有低差 Altitude differenceOm1.00.980.960.940.920.900.880.860.840.82（室機低于室外

45、機時）5m1.00.970.950.930.910.890.870.850.830.81(When indoor10m0.960.940.920.900.880.860.840.820.80Unit higher than outdoor15m0.930.910.890.870.850.830.810.79Unit or indoor20m0.900.880.860.840.820.800.78Lower than outdoor unit)25m0.870.850.830.810.790.77高低差A(yù)ltitudedifference0m1.00.980.960.940.920.900.88

46、0.860.840.82（室機商于室外機時）5m1.00.980.960.940.920.900.880.860.840.82(When indoor10m0.980.960.940.920.900.880.860.840.82Unit lower than outdoor15m0.960.940.920.900.880.860.840.82Unit or indoor20m0.940.920.900.880.860.840.82Higher than outdoor unit)25m0.920.900.880.860.840.82注：等效總長指直管總長再加上彎頭及存油彎的等效長度之和。彎頭及

47、存油彎的等效長度參見下表。Note : The "equivalent total length/r is the straight tubes total length added with equivalent of the elbows and the oil-kept bends. Equivalent length of the elbows and the oil-kept bends refers to following table .彎頭和存油彎等效長度表(m)Table of equivalent length of the elbows and the oil-

48、kept bends (m)氣體連接管外徑mmGas connection pipe' s external diameter彎頭Elbow存油彎Oil-kept bends(pl5.88(5/8")0.32.0(pl9.05(3/4”)0.352.4(p22.2(7/8a,)0.403.0q>28(9/8-)0.53.7(p35(ll/8")0.554.1(p42(13/8")0.604.85 .排水管安裝Installing drainpipe接水盤排水孔和底盤排水孔接頭如下：Joints of drain pan weep hole and c

49、hassis weep hole seen as following :LF/LFD/RF8N LF/LFD68N /RF67N 螺紋接頭 G1HALF/LFD/RF8N LF/LFD58N /RF67N internal screw G"1ALF/LFD85N/RF83N LF/LFD305 外螺紋接頭 G1"ALF/LFD85N/RF83N LF/LFD305external screw G1A排水管安裝如圖所示.注意事項：Attention 排水管走管位置始終不能高過達室機排水孔位置，同時室機另一側排水孔必須用絲堵堵死。冷凝水排至下水道路中需加設U形彎（見圖）以防臭氣

50、吸入空調機。The drain pipe cannot be higher than the water outlet hole of indoor unit, and the other side' s drain water hole must be blocked with screw stopper. If condensed water is to be drained to sewer, the drain pipe must have U shaped bend so as to prevent bad smell from going into air conditio

51、ner.6 .電G接線 Electric wiring接線示意圖 wiring demonstration正確的接線按下圖所示：The correct wiring is showed in the below chart.3N780V 50Hzbreak空湖唯昭器Indoor unitllllONDCFF w ! 11 in J!：a.斷路器選用 Breaker selection 機外接線最關鍵是斷路器的選用。斷路器又稱自動空氣開關，主要是在電路條件下不 頻繁接通和分?jǐn)嗉爱?dāng)電路中發生超限的過載、短路及失壓時能自動分?jǐn)嚯娐分?。?路器分框架式和塑料外殼式兩大類?？照{(diào)機安裝一般使用DZ系列塑

52、料外殼式斷路器, 用作機組電源的接通和分?jǐn)嘀?。The key to the out-of unit wiring is the breaker selection .Breaker, which is also named automatic air-breaker switch, can be used to engage in unfrequented connection and breaking normal circuit condition . In addition, breaker can auto-break the circuit while it happened to

53、o much overload, short-circuit and under tension . Breaker can be sorted into two types : frame type and plastic shell type . Generally, the air conditioner installation adopts DZ series shell breaker, in order to connect or break the unit power .斷路器選擇的一般原則如下：General principles of breaker selection

54、:(1)斷路器的額定電壓不低于線路的額定電壓。Breaker1 s rated voltage mustn1 t lower than the circuit rated voltage .(2)斷路器的額定電流不低于通過它的計算電流。Breaker's rated current mustn11 lower than its computing current which through it. (3)斷路器的類型應符合安裝、設備性能和操作方式的要求。Breaker's type must accord with the installation, plant perform

55、ance and operation1 s demand .b.電源導線選用 Selection of supply conductor導線用于連接電路，選用一般原則如下：Conductors are used to connect the circuit, selection principle as follows : 滿足發熱條件 Satisfy heating term導線在通過計算電流時，具發熱溫度不能超過允許最高溫度。While the computing current pass through the conductor, its temperature should not be higher than maximal temperature allowed .(2)電壓損耗 Voltage loss導線通過計算電流時，其產生的電壓損耗不應超過正常允許的電壓損耗值。While the computing current pass through the conductor, the voltage loss should not b