旋轉門使用說明書

.z.JE092A系列自動旋轉門使用說明書目錄第一章JE092A系列特點和功能····································································31.1JE092A系列自動旋轉門的根本機構···················································31.2主要技術參數··············································································41.3系統特點···················································································4第二章系列自動旋轉門規格參數····································································42.1豪華兩翼旋轉門標準規格································································4第三章兩翼旋轉門的工作方式·······································································53.1JE092A的兩種工作方式·································································53.2旋轉門工作方式···········································································53.2.1旋轉門工作狀態···································································53.2.2旋轉門的操作······································································53.3平移門工作方式···········································································53.3.1平移門工作狀態···································································53.3.2平移門的操作······································································53.4平移門和轉門的切換·····································································5第四章觸摸屏的操作··················································································54.1密碼操作···················································································54.2旋轉門通電運行···········································································64.3旋轉門操作················································································64.3平移門操作················································································84.5轉門轉速調整··············································································94.6展示區的使用··············································································9第五章平安和制動裝置··············································································105.1減速防撞傳感器·········································································105.2防夾傳感器···············································································105.3緊急停頓按鈕············································································115.4殘疾人按鈕···············································································115.5電子眼·····················································································115.6平安開關··················································································12第六章兩翼旋轉門維護··············································································126日常保養····················································································12第一章JE092A系列特點和功能JE092A系列自動旋轉門具有一流的交流變頻技術，進口的關鍵部件及高強度鋁合金框架能保證旋轉門最正確的運行狀態。其所具有的旋轉門+平滑門構造為您提供多種使用選擇。67678541285412312312各局部構件名稱對應代號名稱對應代號名稱1外壁5觸摸屏位置2旋轉翼6門冠3展示區7防塵板4平滑門8雷達操作面板上從上至下各局部名稱序號12名稱急停按鈕殘疾按鈕●額定電壓220VAC±10%，50HZ●額定電流6A●額定總功率1200W●高速調節圍1-4轉/分●低速0.5-2.5轉/分●平滑門開門速度 0.3~0.7m/s(必須由專業人員調整)●平滑門關門速度 0.3~0.5m/s(必須由專業人員調整)●平滑門保持翻開時間0-10秒(必須由專業人員調整)●無極調節轉門速度，自動記憶停電前的運行模式?！?60°全方位參數設定調節?！窀呔人俣缺O(jiān)控，全程無縫隙感知輕微門體阻力，受阻立刻剎車，保證人身平安?！裨b進口傳感器全面覆蓋掃描，無平安盲區?！裰悄軠p速、急剎。根據客戶需要，設定劃分減速區和急剎區域?！裣到y(tǒng)運行時刻監控防夾平安設備，如有故障，系統強制切換至平移門狀態，保證人生平安。●所有硬件系統的故障都直接顯示在觸摸屏上，方便技術員準確判斷故障原因，保證旋轉門在最短時間恢復正常?！褶D門采用PWM完美閉環控制技術，停門平穩，準確，無沖擊力，使用壽命長。第二章系列自動旋轉門規格參數序號部位RH072-36RH072-42RH072-481外壁徑〔D〕3600420048002外壁外徑3780438049803外壁開口寬度〔TW〕1800210024004平滑門開口寬度〔LP〕1700200023005入口凈高度(H)2200-24002200-24002200-24006門冠高度3003003007總高度(TH)2500-27002500-27002500-2700第三章兩翼旋轉門的工作方式1、旋轉門工作方式：在保證通道暢通的前提下，具有良好的冷暖隔離作用?？晒?jié)約空調或暖氣能源，保持室環境溫度。2、平滑門工作方式：用于客流量很大、進出較長物品或室外環境溫度差異較小時。3.2.1旋轉門的工作狀態旋轉門的工作狀態有連續運轉、冬季停位、夏季停位、平開停位三種停位、鎖門。3.2.2旋轉門的操作觸摸屏選擇選擇模式后，轉門自動檢測沒有平安隱患時，開場旋轉正常運行?！簿唧w詳細操作見第4章〕3.3.1平移門的工作狀態平移門的工作狀態有雙向通行、單向進入、單向外出、常開模式。3.3.2平移門的操作平移門的操作受旋轉門控制器控制，不能單獨使用，只有在平移模式狀態下才能使用〔具體詳細操作見第4章〕工作方式的轉換方法：通過主菜單上的按鈕轉換?！簿唧w詳細操作見第四章〕第4章觸摸屏的操作密碼應由專人管理和操作。不得泄露。出廠默認設置密碼為：“0〞。【例】修改密碼方法〔如果只是進入使用只需要完成前兩步即可〕第一次使用本自動門前，應去除門區阻礙門運轉的物體。通電然后按下述步驟進展操作：注意：門的電源接通以后如沒有特殊情況請不要每天切斷供電電源。1、在觸摸屏顯示啟動的情況下旋轉門進入鎖門狀態：旋轉翼旋轉至鎖門位置停下，電子機械鎖將門鎖住。2、觸摸屏選擇冬季停位：無人通行時旋轉翼停在門口封閉位置，當室或室外的雷達檢測到有人通過時，門高速旋轉一周(用于室外溫差大或夜間的情況下)。3、觸摸屏選擇夏季停位：無人通行時旋轉翼停在門口敞開位置，當室或室外的雷達檢測到有人通過時，門以高速旋轉一周。4、觸摸屏選擇平開停位：無人通行是選擇門停在平移門位置，當室或室外的雷達檢測到有人通過時，門以高速旋轉一周。5、觸摸屏選擇連續運轉：無人通行時旋轉翼低速旋轉，當室或室外的雷達檢測到有人通過時，門高速旋轉一周，假設無人通過則門又以低速旋轉。平移門工作方式有四種：雙向通行、單向進入、單向外出、常開模式?！螂p向通行：當自動門處于平移門使用狀態時，旋轉至平移門處于水平位置停下后，旋轉門所有功能失效，平移門處于正常開關進出狀態?！騿蜗蜻M入：當自動門處于平移門使用狀態時，旋轉至平移門處于水平位置停下后，旋轉門所有功能失效，平移門處于只進不出狀態。◎單向外出：當自動門處于平移門使用狀態時，旋轉至平移門處于水平位置停下后，旋轉門所有功能失效，平移門處于只出不進狀態?！虺ｉ_模式：當自動門處于平移門使用狀態時，旋轉至平移門處于水平位置停下后，旋轉門所有功能失效，平移門處于一直翻開狀態?！纠吭O置成平移門狀態且平移門為雙向通行的方法旋轉門采用PWM閉環控制技術，可對旋轉門轉速進展無極調速，調速方法如下:注意：速度設置圍是10~40，調好以后點擊測試運行，速度即可生效。展示區是公司為用戶設計的用來個性化裝點自動門的區域，用戶可以根據自己的意愿在展示區中放置展品。首先用鑰匙按逆時針方向翻開展示門上的兩把鎖，然后從展示門的下橫框處輕輕向外拉開展示門，放上展品后，關好展示門，并鎖好。注意：1〕每個展示區中放置的展品重量不能超過25Kg，否則可能超過自動門的額定負荷，影響自動門的使用。2〕請保管好展示門鑰匙。第五章平安和制動裝置11225454平安裝置及其安裝位置序號種類數量1減速傳感器共42防夾傳感器共43緊急停頓、殘疾按鈕共44電子眼共85平安膠條共2111111111111111111防撞傳感器裝在環上，隨門轉動，當防撞傳感器檢測到人或物時，門會停頓旋轉，對人和垂直平安開關的接觸起緩沖作用。防夾傳感器安裝在外環上，當門旋轉時，在旋轉翼前沿與外壁開口右側立柱之間形成一平安區〔Z〕〔約700mm，可調〕，起防止擠夾行人的作用。旋轉翼轉動時，假設旋轉翼前沿在此區域運行，且傳感器檢測到人或物，則旋轉翼立即停頓轉動，待人或物離開此區域，旋轉翼恢復正常運轉。小心：以上兩種平安裝置對于距離地面400mm圍的物體不起作用，使用時請小心。在出現意外情況時，按下緊急停頓按鈕，旋轉翼立即停頓轉動；緊急停頓按鈕安裝于室開口右側外壁立柱上距地面約1200mm處。小心：緊急停頓按鈕按下后，自動門在任何情況下都停頓旋轉，并且所有的平安保護都不起作用，所以在使用時請?zhí)貏e注意平安。按下殘疾人按鈕，旋轉翼立即以設定的低速旋轉，以保證殘障人士的順利通過；殘疾人按鈕安裝于室外開口右側外壁立柱上距地面約1200mm處。注意：殘疾人按鈕僅在旋轉門工作方式下起作用。在平滑門兩側對稱安裝有8對紅外線電子眼〔如以下圖〕，可以提供以下平安保障：減速紅外線制動停頓紅外線減速紅外線制動停頓紅外線1〕旋轉門減速/制動：使用旋轉門方式時，可分別控制旋轉翼的減速/制動，防止撞傷出入的行人。減速〔高/低位〕平安設置：旋轉翼轉動時，假設有人或物遮斷“減速〞紅外線時，則旋轉翼立即減速運轉，待人或物離開時，旋轉翼恢復正常運轉速度。制動平安設置：旋轉翼轉動時，假設有人或物遮斷“制動〞紅外線時，則門立即制動停頓，待人或物離開時，旋轉翼恢復正常運轉速度。2〕平滑門防夾翻開：使用平滑門工作方式時，每側有兩組紅外線可在平滑門運行過程中起防夾的作用。這兩組紅外線是旋轉門的高位減速和低位減速紅外線。平滑門運行時，假設在這兩組紅外線檢測到人或物，則平滑門立即翻開，并保持翻開；待人或物離開后，平滑門恢復正常運行。小心：紅外線電子眼的探測區為距離地面約100mm的水平面，超過該高度的物體將不被探測，所以當您背著小孩和物體時，請注意通行平安。注意：電子眼的安裝位置和角度已在安裝時調整好，在使用過程中請不要擅自掰動，以免造成感應失效，危及平安。在旋轉翼前沿安裝有平安開關，當旋轉翼轉動時，平安開關假設被人或物擠壓，門立即制動停頓，防止擠夾和碰撞行人。待人或物離開，且平安開關復位后，門繼續轉動。注意：平安開關兩端安裝有感應器，在使用過程中應防止強烈的沖擊。同時該感應層是一種特殊的橡膠，要防止銳器損壞外表，否則以上的操作都可能造成平安開關的失靈。第6章兩翼旋轉門維護1、-清掃地面，保證旋轉翼下方?jīng)]有污物及灰塵，卡住的異物要用鑷子去除。-使用清潔劑擦洗玻璃。-使用干凈的軟濕布擦拭門體。注意：在清洗自動旋轉門的各個控制開關、感應器件時，應注意電器平安。在清洗照明燈時，請在照明燈熄滅15分鐘后清洗，以免燈玻璃由于受冷破碎。-保證各類使用說明標識、平安警示標識的完整和清晰。-檢查旋轉翼密封是