LED的使用注意事項--中英.ppt_第1頁
LED的使用注意事項--中英.ppt_第2頁
LED的使用注意事項--中英.ppt_第3頁
LED的使用注意事項--中英.ppt_第4頁
LED的使用注意事項--中英.ppt_第5頁
已閱讀5頁,還剩9頁未讀, 繼續免費閱讀

下載本文檔

版權說明:本文檔由用戶提供并上傳,收益歸屬內容提供方,若內容存在侵權,請進行舉報或認領

文檔簡介

1、1,LED的使用注意事項 LED USING INSTRUCTIONS 報告人:莫輝職位:臺灣億光電子業務員 Email:mheverlight-電話2,LED的使用注意事項 LED USING INSTRUCTIONS,概述:general: LED加工的注意事項 LED processing instructions LED焊錫的注意事項 LED soldering instructions LED使用電路的注意事項 LED using circuit instructions 其它 others,3,LED的使用注意事項 LED USING INSTRUCTIO

2、NS,現狀說明:越來越多的客戶抱怨LED經客戶使用後有缺亮、色澤不均、亮度不均等不良狀況,經對不良品進行分析,有大多數為客戶在測試及應用上不當而產生之不良,建立此檔案引導客戶正確使用LED。 present problems: more and more customers complained led have the problems of lack of brightness , inequable colour and lustre , inequable brightness. We found that the majority customer testing and using

3、 our product in a wrong way after we test the abnormal products , so we establish this profile to lead customer using LED correctly.,4,LED的使用注意事項 LED USING INSTRUCTIONS,LED加工的注意事項led processing instructions A、LED在剪腳時建議采用自動機臺進行剪腳,且保持刀片峰利,以防止扭距應力拉扯膠體與支架,產生應力破壞LED內部結構。Using the machine to cut ,and shou

4、ld keep blade sharp to protect epoxy and leadframe from twist pressure, which may make damage to the leds inside structure. B、建議LED成形加工時在焊錫前,如在焊錫後立即進行加工,此時LED膠體內部還存在一定的溫度,若用手碰觸或外力碰觸到膠體,因膠體特性會產生應力拉扯斷第二焊點 。Do the figuration processing before soldering ,if do it before soldering immediately , there wou

5、ld be temperature inside the epoxy, and if touching or outside force on the epoxy, the pressure would pull the second soldering point to crack. C、支架成形形狀需要與PCB上的間距一致,以防止LED在插在PCB上有拉扯的狀況。The leadframe figuration shape should be consistent with the space on the PCB, in case that there is a pull when LE

6、D insert in the PCB.,5,LED的使用注意事項 LED USING INSTRUCTIONS,LED加工的注意事項led processinginstructions D、LED在折腳加工時,建議固定LED PIN腳後進行加工,以防止應力的產生。 When curving , we suggest that processing after fix up PIN, in case of pressure . E、需離膠體2毫米才能折彎支架。 Keep 2mm from epoxy in order to twist lead frame. F、圖示如下:refer to p

7、ictures,6,LED的使用注意事項 LED USING INSTRUCTIONS,LED加工的注意事項 LED processing instructions,7,LED的使用注意事項 LED USING INSTRUCTIONS,LED焊錫的注意事項 LED soldering instructions A、LED無鉛焊錫波峰焊條件(焊錫位置距膠體距離最小為3mm),曲線圖如下:the condition of wave soldering (the soldering point should keep 3mm from epoxy at least) , as the pictur

8、e:,8,LED的使用注意事項 LED USING INSTRUCTIONS,LED焊錫的注意事項 LED soldering instructions B、LED手焊條件:hand soldering conditions: 烙鐵溫度300度(MAX),時間3S(MAX),建議使用恆溫烙鐵。Iron temperature 300(max), time3s(max), constant temperature is better. C、LED不支持REFLLOW焊錫。 LED don not support REFLLOW soldering. D、LED避免在高溫下碰觸其膠體與PIN腳,以

9、防止應力拉扯斷第二焊點。Avoid touching epoxy and PIN under high temperature, in case that pressure pull the second soldering point to crack.,9,LED的使用注意事項 LED USING INSTRUCTIONS,LED焊錫的注意事項 LED soldering instructions E、禁止LED在高溫下加工。Reforming under high temperature is forbidden. F、 建議客戶在經波峰焊後加裝風扇,以利散熱,需等LED冷卻後(最好為室

10、溫後),再進行下一工序加工。We suggest that installing a fan after wave soldering to dispel heat ,do not do the next process until led cool (room temperature is better),10,LED的使用注意事項 LED USING INSTRUCTIONS,LED使用電路的注意事項led using circuit instructions A、建議LED使用時,需串電阻作業,以防止大電流或大電壓燒損晶片,有部分客戶投訴亮度不均及色澤不均,均為大電流或大電壓燒損所致。如

11、下電路: In order to protect chip from burning which due to high current or voltage, a resistance is needed when using LED, some customers complained that inequable colour and lustre or inequable brightness, which all because of high current or high voltage. As the picture,11,LED的使用注意事項 LED USING INSTRU

12、CTIONS,LED使用電路的注意事項led using circuit instructions B、舉例說明:examples G晶片在未串電阻的情況下,給電壓2.2V,其電流為100mA以上,其發光顏色已趨的於橙色,時間過長會燒損晶片,如下圖片:the color of chip G is orange when there is no resistance and voltage is 2.2V,current is 100mA, the chip would be burned during a long time.,有加電阻Haveresistance,未加電阻NO resista

13、nce,12,LED的使用注意事項 LED USING INSTRUCTIONS,其它 others A、靜電注意事項:instructions on static 針對要求防靜電之機種,要確實做好防靜電措施,以下為藍光晶片靜電燒損圖片(晶片只部分發光): Concerning to the prevent static machines ,make sure the prevent static measures is done , the blue chip burned as the picture. (part of chip give out light ),13,LED的使用注意事

14、項 LED USING INSTRUCTIONS,其它others B、針對我司有進行分光分色之材料,不同等級請客戶不要進行混用,以 防止亮度及色澤差異。According to the materials which could distinguish light and color , customers could not mix the different rank material, in case that brightness and color and lustre go wrong . C、當用化學品清洗膠體時必須特別小心,因?yàn)橛行┗瘜W(xué)品對膠體表面有損傷并引起褪色如三氯乙烯、丙酮等??捎靡掖疾潦?、浸漬,時間在常溫下不超過3分鐘。Be care when cleaning epoxy with chemical, because some chemical may cause damage to the surface of epoxy and even to fade .washing a

溫馨提示

  • 1. 本站所有資源如無特殊說明,都需要本地電腦安裝OFFICE2007和PDF閱讀器。圖紙軟件為CAD,CAXA,PROE,UG,SolidWorks等.壓縮文件請下載最新的WinRAR軟件解壓。
  • 2. 本站的文檔不包含任何第三方提供的附件圖紙等,如果需要附件,請聯系上傳者。文件的所有權益歸上傳用戶所有。
  • 3. 本站RAR壓縮包中若帶圖紙,網頁內容里面會有圖紙預覽,若沒有圖紙預覽就沒有圖紙。
  • 4. 未經權益所有人同意不得將文件中的內容挪作商業或盈利用途。
  • 5. 人人文庫網僅提供信息存儲空間,僅對用戶上傳內容的表現方式做保護處理,對用戶上傳分享的文檔內容本身不做任何修改或編輯,并不能對任何下載內容負責。
  • 6. 下載文件中如有侵權或不適當內容,請與我們聯系,我們立即糾正。
  • 7. 本站不保證下載資源的準確性、安全性和完整性, 同時也不承擔用戶因使用這些下載資源對自己和他人造成任何形式的傷害或損失。

評論

0/150

提交評論