ST-16020-6--產品規格書--PT--中性2(1)2

1、產品規格書產品名非晶硅太陽能電池品牌名稱制造商產 地產品規格160*20*1.1 mm產品型號16020-6產品規格書參數表Specificati onParanm eter Specificati on1、Name & Model名稱、型號1. 1: Name 名稱SOLAR CELLS1 . 2： Model 型號16020-62、性能參數項目參數2.1尺寸160*20*1.1 mm公差：土 0.2mm2.2開路電壓最小值2.5 V典型值3.0 V2.3短路電流最小值55 uA典型值60 uA2.4負載特性最小值2.0 V典型值2.2 V2.5工作溫度-545 C2.6保存溫度、溫

2、度-2060 C濕度 <75%2.7使用照度范圍0100000Lux2.8測試條件FL 200Lux、25 C注：1、產品出廠時以：“工作電壓為檢測標準200LukA-p jjA3、工作電壓Vop和工作電流lop測試原理圖:被 測 電 池4、產品圖TF 面1.1 irm±Q. 1 ktST-I6020-6jll-IIUSDUIfELlsaiwrwi-wSriHlI -blHWdlnkuaiEih_LR1W13I9-|!-91AP Ri1 A Ho IFwjVbjuihiiri占戌電科占w二曰ttEUBUlME|!IL4I1SIBn業 |=7 "M MT. IT可:此

3、FFXIKLKTVbi 】IV附加說明-Additi onal in struct ions5、Outgoing inspection 成品檢驗5. 1 Inspection method 檢驗規定Outgoing inspections shall be based on random sampling, Normal inspxtion by single sampling based on MIL-STD-105D shall be applied.成品檢驗采取隨機抽樣方案，抽樣方安按MIL-STD-105D執行5. 2 Outgoing inspection results shall

4、 be usually tested by the inspection result table. 成品檢驗結果將以測試報 告表/合格證形式提供6、 Regulation for product solder:成品可焊性檢驗規那么6. 1 Purpose 目的Let the product including the condition for lead-free soldering be standard and ensure the sodering quality of product in the factory out of the factory。標準公司產品可焊性試驗作業，確保

5、入庫出廠產品可焊性質量，包括滿足無鉛焊錫焊接條件。6. 2Range 范圍It is adequste for all the soldering product of the ccompany.適用于本公司所有產品的可焊接性試驗作業。6. 3 Stadard of the employment 引用標準Q/SMC-001-2000,?Standard for the corporation producing Solar Cell of dm light and amophous silicon ?。 Q/SMC-001-2000,?弱光性非晶硅太陽能電池產品企業標準?。6. 4 Defin

6、ition 定義SolderingThe ability and intensity of the soldering between the lead-free tin and the products copperunder the rating condition.可焊性產品電極材料銅漿的焊接強度、能力6. 5 Condition of soldering ecperiment 可焊接性試驗條件6. 5. 1 Soder: It is fit for the lead-free tin and other rosin tin.焊接材料：無鉛焊錫或含松香的其它焊錫 絲6. 5. 2 Sol

7、dering temperture: 260 C- 330C .焊接溫度：260 C- 330C .6. 5. 3 Soldering length should be less than 3 secinds.焊接時間：w 3 秒鐘。6. 5. 4 Condition of Iron: The same temperatiure and pow should be less than 30W. 烙鐵要求： 恒溫、 功率w 30W。6. 5. 5 Soldering time: Repeat that not more than twice.焊接次數：重復不得超過2 次6. 6 Standard

8、 for regular soldering ecperiment for one piece of the product.可焊性試驗合格片標準 6. 6. 1 Soldering dot must be or of und and it must cover more than 2/3 of each copper.焊點光滑圓潤， 焊點面積占銅漿2/3以上為合格片。6. 6. 2 Tensile test: Pulling must be more than 0.5 Kg 拉力測試：拉力?0.5Kg6. 7 Standard for regular soldering ecperiment for each group of the product.可焊性試驗產品合格批標準。6. 7. 1 Operative frequency: Batch.實施頻度：每批。6 . 7 2 Probaive method: Sample and visualzation.檢驗方法：抽樣、目測。 6 . 7 . 3 Sample number: 10pcs.抽樣樣本數：10pcs.6 . 7 . 4 。按 6.5.1 和 6.5.2 步驟進行焊接和拉 力試驗。6 .