KT型可曲撓橡膠接頭

1、KXT型可曲撓橡膠接頭KXT flexible rubber joi ntPage27材料表 Table of Materials序號SerialNo部位Prti on材料Material1主體Mai n極性橡膠polarizedbodyrubber2內襯Li ning尼龍簾布Nylon cordfabric3L架 I骨架Frame硬鋼絲 hard steel wire4法蘭Fla nge軟鋼 Mild steer技術條件 Tech ni cal Con sition型號ModelKXT-( I)KXT-( n)KXT-(川)工作壓力 MPa( kg.f/cm2 )Worki ng press

2、ure2.0(20)1.2(12)0.8(8)爆破壓力 MPa( kg.f/cm2 )Bursti ng pressure6.0(60)3.5(35)2.4(24)配套法蘭 MPa( kg.f/cm2 )support ing flange1.6(16)1.0(10)0.6(6)真空度 Vacuity KPa(mmHg)100(750)86.7(650)53.3(400)適用溫度Applecabletemp. °C-20C - 80C （普通型）+80C -135C （特殊配方）適用介質Applecable media空氣、壓縮空氣、水、海水、熱水、弱酸Air.Compressed

3、air. Water.Sea Water. Hot Water.Weak acid.Etc接頭兩端可任意偏轉，便于自由調節軸向或橫向位移。Both ends of the joi nt ca n be arbitray deflected for freeadjustme nt of axial or lateral displaceme nt.注：DN20C 300KXT- 型工作壓力為1.5MPa(15kgf/cm2)爆破壓力為4.5MPa(45kgf /cm2)普通型產品只能在 80C以下，如需135C以下需指明，更換橡膠配方，包括耐油、耐酸堿等。壓力較高及沖擊力較大時宜采用限位拉桿裝置

4、。Note: The working pressure of Model DN200 300KXT-(1)is 1.5MPa (15kgf/cm2) and the bursting pressure is 4.5MPa(45kgf/cm2). Ordinary type products can only be used under 80°C if temperature is higher than 135°C, please show clearly . ingredient of the rubber will be changed Restricting pull

5、 rod is necessary . when pressure is high and impulse is great公稱通徑、長度、位移數值與法蘭主要數據表Table of Main Parameters of Nominal Core Diameter， Length，Displacement Value and Flange螺栓孔螺栓孔中心圓橫向位螺栓偏轉角度公稱能徑長度數直徑直徑軸向位移移An gle of安裝間距DiameteDiameter ofLateraNominal coreLen gthNo.oAxial dispdeflectioin stallatior ofbo

6、lt holeldiameterl(mm)flace nmen t(mm)nn space < mmboltcen terdisplabolt(a 1 + a 2)holecirclen D1cndo(mm)(mm)eme nt1(mm寸in)伸長Strec h壓縮Compression(mm)32(11/4)95417.5100699150440(11/2)95417.51106109150450-2105417.5125710101504(21/21115117.51451150I80-3135130817.5160815121504100-4150135817.5180101913

7、1504125-5165160817.52101219131504150-61801858222401220141505200-81902008222951625221505250-1023024012223501625221506300-1224026012224001625350-1426516224601625400-1626516265151625450-1826520265651625500-202652026620162522222222221506150715071508600-24265700-28260/320800-32260/340900-36260/3701000-40

8、260/4001200-48260/42028203025228243016252282433162522833162522828361625228324118262497251508401009501001050100116010013801001400-56300/4503642159020282610091600-64300/50040481820253530100918005004448202025353010010200055048482230253530100102200-8858052422390253530100102400-9661056422600353010010注：1、

9、表中法蘭標準采用 689119PNI.OMPa對應配對法蘭應是閥門法蘭或符合6B/T9115.1 2000(RF)法蘭，安裝間距是指軟接頭法蘭與管道上法蘭安裝后的間隙，并保持均勻一致，以防拉脫。 2 、其他標準或非標準法蘭需另訂協議，指明標準或提 供圖紙及有 關數據，本廠可定制生產。3、公稱通經較大時(>700)建議采用大翻邊球體產品。4、懸空給水使用DN 200以上產品，管道必須有固 定支撐或固定托架，否則產品應安裝防拉脫裝置。Note:1 、 FImIge standard is GB9119 PNI.0MPa；TIie matcIfiIN fImge siIotdd be vaIv

10、e fImIge or oiIier fImIges according with GB/T9115.12000(RE)The instaIIation space refers to the gap between soft joint fIange and pipe fIange andit shouId be maintained uniform to avoid puIIing or shedding 3、 For fIanges of other standards or non-standarditis necessary to be agreed upon separateIy pIease speciy standard of furnish diagram and reIative parameter,we wiIImanufacture accordingIy 3、 sphericaI products with wide fIanging are suggested wheninside nominaI diameter is greater than or equaI to 700 4、 Use those products exceeding DN200 w